This project was completed by the Historic American Engineering Record (HAER), a long-range program to document historically significant engineering and industrial works in the United States. Heritage Documentation Programs of the National Park Service, U.S. Department of the Interior administers the HAER program. The SS Cape Inscription documentation was prepared under the direction of Todd Croteau (HAER Maritime Program Coordinator) for the Maritime Administration (MARAD) in Wesley Hale wrote the historical report under the supervision of Justine Christianson, HAER Historian. Jarob Ortiz produced the large- format photographs. Drawings were prepared by Onairis N. P rez and Cristina I. Montenegro-Torres in SS CAPE INSCRIPTION HAER No. CA-2333 (Page 3) Part I: Historical Information A.
Physical History 1. Date of Construction: The keel was laid down on July 1, and launching took place on May 24, The completed vessel was delivered to States Steamship Company (States Line) on April 27, 2. Designer/Naval Architect: The Maritime Administration s C7 Lancer-class vessels were the first purpose-built container ships and proved successful as the civilian merchant sector shifted to containerized cargo. States Line wanted four modified Lancer-class type vessels, designated C7-S-95a. Henry Company of New York was involved in developing this design, which featured an aft cargo ramp to facilitate more flexible cargo- carrying capabilities. James J. Henry, president of the company, was well known for his work in developing containerized cargo ships.2 3.
Builder: States Line ordered the four C7-S-95a vessels from Bath Iron Works of Bath, Maine, in 4. Original Plans and Construction: The specifications for the C7-S-95a vessel type developed by Henry Company stipulated a welded-steel hull with a cast-steel or welded-steel stern frame and internal steel bulkheads. The vessel would be comprised of four decks divided into four cargo holds. Break-bulk cargo would be stored in hold 1, which would be loaded by the twin 15-ton cranes located over hatch 1 on the A deck. The remaining three holds would be used for carried-on cargo, loaded via a stern door and ramp (the major difference from the C7 Lancer-class design).
This stern ramp, consisting of three sections for a total length of would attach to the hull by hinges and operate via a hydraulic mechanism. It would be located at an approximately 40-degree angle to the centerline on the starboard side of the vessel. Access between the cargo holds would be facilitated by internal fixed ramps generally measuring 24' wide and sloping about 7 degrees. The following chart shows the capacities of the holds. 1 Naval Vessel Register - CAPE INSCRIPTION (AKR available at accessed August 16, 2 James J. Henry, 73, Designer of Containerized Cargo Ships, New York Times, November 4, Jim Shaw, What Ever Happened to States Line? Pacific Maritime Magazine, June 1, available at accessed August 2, 3 Shaw, What Ever Happened. SS CAPE INSCRIPTION HAER No.
CA-2333 (Page 4) Hold/Ramp Bale (cubic feet) Area (square feet) Hold 1 Hold 2 Ramps Hold 3 Ramps Hold 4 Ramps A Deck Total (holds) Total (ramps) Grand Total The propulsion would consist of a cross-compound double-reduction geared turbine and two steam generators driving a propeller through line shafting.4 Crew and passenger accommodations were placed in the superstructure.
The cargo-carrying and handling equipment included two diesel 50,000-pound, low-profile straddle carriers to handle steel, lumber, and other types of long cargo; two 32,000-pound forklift trucks with 96" forks; six 22,000-pound low-profile forklift trucks with 48" forks; one riding-type sweeper with a gasoline motor; one four-wheel drive jeep; and an electric vehicle capable of carrying one person (much like a small golf cart).5 The general design of the class consisted of four cargo holds with compartments on four decks, as well as room on the main deck for containers. The A deck was located at above baseline, the B deck at above baseline, the C deck at above baseline, the D deck at above baseline, and the E deck (or tank top) at above baseline.
Cargo could be loaded through the stern ramp or the original twin Hagglunds cranes, each with a lifting capacity of 15 tons. The forward cargo hatches allowed cargo holds 1 and 2 to be loaded by the 15-ton cranes. The hatch covers opened accordion style by hydraulic mechanisms, allowing operation by a single crew member. The remaining compartments in the vessel were accessed by a series of hydraulic ramps that could be lowered and raised as necessary to facilitate the movement of cargo between decks. Once the holds were filled, the ramp covers could be lowered flush with the deck, providing more surface area on which to store cargo and vehicles.
Cargo hold 4 was at the stern of the ship, just above the machinery spaces where the vessel s twin General Electric steam turbines drove the single-screw propeller. Two Babcock and Wilcox boilers capable of pressure of pounds/square inch (psi) provided the steam for the turbines. A Bird Johnson Company KaMeWa bow thruster designed to produce pounds of thrust aided the ship s propulsion.
4 Experiments were done on a skewed propeller to reduce vibration at the request of the Henry Company by the Naval Ship Research and Development Center of Bethesda, Maryland, in See Boswell and Kader, The Design of a Skewed Propeller for the States Steamship Company Roll-On, Roll-Off Cargo Vessels, prepared for Bath Iron Works Corporation, Ship Performance Departmental Report, August 5 Henry Co., Inc., Specifications for Combination Ro/Ro Container Ship for States Steamship Company, April 4, SS CAPE INSCRIPTION HAER No. CA-2333 (Page 5) The MA Design C7-S-95a plan dated November has a different layout of the superstructure than what was built and notes different superstructure deck elevations above the baseline of the vessel.
The top of the superstructure, for example, is noted as above baseline on the plan but a capacity plan with later annotations shows it as above baseline. These changes may have been the result of States Line deciding to accommodate a limited number of passengers between States Lines ports. The plans show the galley and cook s stores on the ship s centerline on the A deck. The officers and passengers would take their meals in their own mess on the starboard side of the vessel, while the crew would take theirs on the port side. Cabin spaces for kitchen crew would flank the machinery casing, which was in the forward centerline of the superstructure. The fan room for cargo hold 2 would protrude just forward of the superstructure on the cargo deck.
The cabin deck, located at above baseline, would have accommodations for twelve passengers as well as the offices and staterooms for the engineering officers. At the aft end of the cabin deck would be the lounge with an area where passengers could enjoy refreshments, look out the large windows facing the vessel s stern, or step onto the verandah. Next the upper deck, elevated above baseline, would have accommodations for the radar technician, captain, and chief mate. The staterooms for two cadets and the Second and Third mates would be on this deck as well, just below the navigation bridge deck.
The bridge (at above base line) would house the wheelhouse, gyro room, and chart room, and would be slightly elevated from the navigation bridge deck at The ship s radar and navigation equipment would be installed on top of the deckhouse.6 5. Modifications: Cape Inscription retains most of the original design features but has undergone several modifications throughout its years of service. The twin 15-ton cranes were replaced with a single 30-ton crane capable of lifting the forward pontoon-style hatch cover that had replaced the accordion-style one when the hydraulics malfunctioned.
Both the cranes and hatch covers were replaced at some point in the early The air- conditioning units on the bridge have been replaced several times due to problems caused by the heat when the vessel was stationed in the Middle East. The bridge electronics have also been swapped out several times to keep them current and up to date. For the same reason, the radar and navigation gear has also been replaced with newer, more accurate models. The two lifeboats that once flanked the superstructure were replaced by a single stern drop boat davit in that features a motor-propelled lifeboat capable of carrying seventy people.7 6. Names: For the short time States Line owned the vessel it was called SS Maine.
After the company went bankrupt in Whitney National Bank (now Hancock Bank) seized the ship and leased it to Lykes Brothers Steamship Company, who renamed it SS Tyson 6 Maritime Administration, Design C7-S-95a, Cargo Vessel for States Steamship Company, M.A. Plan No. Capacity Plan, Bath Iron Works Corporation, B.I.W. Plan No. submitted May 22, Office of Ship Construction, Maritime Administration, Department of Commerce, States Steamship Company, Single Screw Cargo Vessel, MA Design C7-S-95a, November M.A. Plan No. C7-S-95a-S9-0-1. 7 Edmund O Shea (Chief Mate of Cape Inscription), interviewed by Wesley Hale at Long Beach, California, August 2, SS CAPE INSCRIPTION HAER No. CA-2333 (Page 6) Lykes. In the Maritime Administration acquired the vessel and renamed it SS Cape Inscription.8 B.
Historical Context States Steamship Company ordered the Maine-class roll-on/roll-off vessels (comprised of SS Maine, Arizona, Nevada, and Illinois) in an effort to improve business. The failing company had been slow to adapt to the growing use of containers in international shipping. Lumber merchant Charles Dant had founded the States Steamship Company in as the Columbia Pacific Steamship Company to handle the lumber being exported from the Columbia River to Asian and European markets. Dant leased several World War I-built steamers to make his company commercially viable and competitive against the sailing schooners in operation at the time.
Columbia Pacific Steamship Company had expanded beyond the Columbia River loading ports by the prompting the name change to States Steamship Company or States Line, as it was familiarly known.9 States Line lost many ships during World War II, and Dant rebuilt his fleet using a combination of Liberty, Victory, and wartime C3 cargo vessels until he could afford to purchase new ships. During the and he ordered three classes of ships, the first of which was the C4-S-1u type, which included California, Oregon, Washington, and Hawaii. This class served States Line until the when they were chartered to Prudential-Grace Lines as gas prices rose during the oil crisis, and the Vietnam War began winding down.
Without government contracts to support them and the global market shifting to containerization, the C4-S-1u type vessels quickly became obsolete.10 The second class built for the States Line was the cargo ships, including Colorado, Montana, Idaho, Wyoming, and Michigan, all of which were delivered in the late after containerization had firmly taken hold as the primary means of shipping. These were some of the largest general cargo vessels constructed at that time, measuring long and 82' wide with a bale capacity of cubic feet. They were fast as well, with a service speed of 21 knots. The class was a modified version of the C4 Mariner class and featured automated boilers, advanced pilothouse controls, and bow thrusters.
Though the Colorado class possessed an extremely versatile design, they were built too far after containerization to prove useful, and after the government contracts during Vietnam dried up, they too became obsolete.11 Unfortunately for States Line, it possessed a fleet of obsolete and inadequate ships that used too much gas and cost more money to operate than they brought in through their voyages. In an effort to save its business, States Line contracted the Maine class MARAD designation C7-S-95a. These were modified C7 Lancer-class vessels that featured an aft cargo ramp to handle a variety of cargo types but were also still purpose built to carry containers.
Bath Iron Works of Bath, Maine, built the class, comprised of SS Maine, Arizona, Nevada, and Illinois, in the early These vessels were long with beams of and operational speeds of 23 knots furnished by the two General Electric steam turbines. They were delivered to 8 Shaw, What Ever Happened. 9 Shaw, What Ever Happened. 10 Shaw, What Ever Happened. 11 Shaw, What Ever Happened. SS CAPE INSCRIPTION HAER No. CA-2333 (Page 7) States Line with accommodations for twelve passengers in six staterooms on the cabin deck.
The States Line operated SS Maine along the Pacific trade routes for the short time it was in service with the company.12 Despite their successful and versatile design and popularity as passenger charters, the Maine- class vessels were not enough to save States Line from financial ruin. In December the company filed for bankruptcy, and its fleet was sold. SS Maine was originally sold to Whitney National Bank, which then leased the vessel in February to the Lykes Brothers Steamship Company, who eventually purchased it. Lykes Brothers renamed the vessel Tyson Lykes and operated it in the trans-Pacific trade. In the Maritime Administration acquired Tyson Lykes and placed it in the Ready Reserve Force where it was renamed SS Cape Inscription. C.
Operational History As part of the Ready Reserve Force SS Cape Inscription can be activated for use by the Military Sealift Command on short notice. Initially used to transport goods for private shipping companies, Cape Inscription later participated in military exercises and missions for the In the vessel participated in Operation Bright Star 90, a joint training exercise held every two years with U.S. and Egyptian forces. The exercise was designed to strengthen the ties between the U.S. and Egyptian militaries and improve readiness and interoperability between U.S., Egypt, and other participating forces.
13 In August Cape Inscription and the other seventeen roll-on/roll-off (Ro/Ro) vessels in the Ready Reserve Force were activated for service in Operation Desert Shield, which at the time was the largest buildup of military forces since the Vietnam War. The U.S. Navy specifically requested deployment of the Ro/Ros because they were suited to deploy military vessels in a forward staging area.14 In Cape Inscription participated in Operation Uphold Democracy, the U.S. mission to reinstate the government of Jean-Bertrand Aristide. Aristide was the first popularly elected president in Haitian history but was overthrown in a military coup by Lt. Gen. Raoul Cedras. President Bill Clinton deployed U.S. military forces to Haiti to intervene on behalf of Aristide.
The mission was completed without any bloodshed, and the activated vessels returned to port.15 Throughout its service history with the Ready Reserve Force, Cape Inscription has participated in various training exercises and relief missions and has supported numerous military operations. As a roll-on/roll-off vessel, it proved especially useful in rapid deployment operations such as Desert Storm and Enduring Freedom. The vessel is frequently 12 Further research into company records would be necessary to determine the types of goods Maine/Tyson Lykes transported along its routes in service to the States Line and Lykes Brothers. 13 Lt. John Ripley, Reservists Shine in Bright Star, The Navy Reservist 32, no. 5, (May 14 Samuel K.
Skinner, MARAD 90: The Annual Report of the Maritime Administration for Fiscal Year (Washington, DC: U.S. Department of Transportation, April vii, 54. 15 Intervention in Haiti, Milestones: Office of the Historian, U.S. Department of State, available at accessed June 23, SS CAPE INSCRIPTION HAER No. CA-2333 (Page 8) used in military exercises designed to make deployment of military supplies as efficient as possible. Part II. Structural/Design Information A. General Description 1. Overall: Cape Inscription is a roll-on/roll-off container ship with a loading ramp at the stern. It has a streamlined profile with ample deck space for containers that can be loaded into the cargo holds via the forward 30-ton crane or by the stern ramp.
Crew quarters are in the deckhouse at the stern of the vessel, while the rest of the ship s space is comprised of cargo holds. 2. Decks: Since the ship was designed to optimize cargo-carrying capacity, much of the space below deck was designed to hold containers and vehicles. The fore peak compartments contain the bosun s stores, chain locker, and machinery for the windlass and bow thruster above the salt-water ballast tank. The anchor windlass and forward cargo cranes are in the forward section of the A deck. The section amidships is largely designated for containers and features port and starboard fan enclosures that provide ventilation to the lower decks. A ramp enclosure is positioned on the port side amidships.
Containers and vehicle cargo can be stacked on top of the enclosure to maximize deck space. Inside the superstructure on the A deck are the crew and officers mess, the galley and cook s stores, and accommodations for eight members of the galley crew. The cabin deck is located one level above A deck and contains accommodations for the able-bodied seamen and unlicensed engineers. The boat deck also contains the bosun s storeroom, the crew lounge, and the crew laundry facilities and storage areas. The cabin deck originally had staterooms for twelve passengers, but once the Maritime Administration acquired the vessel, the staterooms were used by military personnel or extra crew.
The chief and assistant engineers offices and staterooms are on this level, along with laundry facilities and a stern-facing lounge. In the original design, passengers and crew would have accessed the lifeboats from this deck, but with the addition of a stern drop boat davit, the port and starboard lifeboats have been removed. The master s office and stateroom is on the upper deck, as well as the quarters for the chief mate and radio operator. Cabin spaces for two cadets, relief officer, and pilot are located on the upper deck, all of which wrap around the central machinery casing and emergency generator room. Just above the upper deck is the navigation bridge deck, which houses the wheel house and chart room.
The bridge provides ample height for the crew to see over the tops of any containers stacked on the deck. The ship s radar equipment is located on the house top in front of the exhaust funnel. 3. Cargo Holds: Cape Inscription has four cargo holds divided into twelve compartments across four decks. Hold 1 is the forward most hold and has two compartments one each on the B and C decks. Cargo is placed into this hold through a x 27' hatch on the A and B decks. Hold 1 has a bale volume of cubic feet on the B deck and SS CAPE INSCRIPTION HAER No. CA-2333 (Page 9) cubic feet on the C deck. Hold 2 has compartments on all four decks, with cubic- feet capacity on the A deck where containers are loaded with the ship s crane.
Access to the lower decks of hold 2 is achieved through watertight hydraulic ramps that rest flush with the deck above. The layout of hold 3 is identical to that of hold 2, with four compartments across all decks and access ramps to each. Hold 4 is located directly above the ship s machinery spaces, and as a result, it can only store cargo on the B and C decks. B deck has a bale capacity of cubic feet and is accessed by a ramp leading upward from C deck. Except for the containers loaded by the ship s crane, all cargo passes through hold 4 on the C deck since that is where the ship s stern ramp is located.16 4. Crew Accommodations: Cape Inscription was designed to accommodate a crew of forty-three with space for twelve passengers.
The officers were housed in the upper deck while most of the deckhands stayed on the boat deck. After MARAD acquired the ship, the passenger staterooms on the cabin deck were reserved for the transportation of troops and other military personnel as required. The galley and mess areas are on the A deck within the deckhouse. 5. Safety: The ship is equipped with a stern boat drop davit for lowering a seventy-person motorized lifeboat measuring Several other floatation devices are distributed throughout the ship. B. Mechanical Features 1. Engine Plant: Cape Inscription has twin General Electric cross-compound double reduction geared steam turbines driving a single-screw propeller.17 2. Boilers: Two Babcock and Wilcox high-pressure boilers produce pounds of steam per hour per boiler.
The boilers are original to the ship. 3. Electrical System: Two DeLaval electric turbines operating at shaft revolutions per minute generate the ship s electricity. 4. Cargo-Handling Arrangement: Most of the ship s cargo is loaded via the stern cargo ramp. A single 30-ton cargo crane loads the cargo through the forward hatch into hold 1 and stacks containers onto the A deck. 16 Division of Naval Architecture, U.S. Maritime Administration, RRF Loading Characteristics Pamphlet, SS Cape Isabel, January 17 Engineering Operating Manual, Cape Inscription, C7-S-95a, Thorner-Lawrence Associates, Inc. Chesapeake, VA, SS CAPE INSCRIPTION HAER No. CA-2333 (Page 10) Part III. Sources of Information A. Primary