Litchfield County, Connecticut - Chapter with an unread heading (no. 12 of those read), 1881
From History of Litchfield County, Connecticut, published 1881. 7,663 words, reproduced complete and unedited. Source changes inside the text are labelled in place.
Contents
2 sectionsThe section headings the book prints inside this chapter. Each one jumps to where it begins.
The text
7,663 wordsMachine-read from scans of History of Litchfield County, Connecticut, published 1881. Nothing has been corrected: fixing what looks like a misspelled name is how an invented one gets published. Source changes are marked where they occur.
Chapter with an unread heading (no. 12 of those read)
Wooden-wake. - The saw-mill was, of course, the first utilization of water-power in this as in most other primitive communities. The location of the earliest of these has already been noted. Besides supplying the home demand for lumber, they early turned out a limited supply of white-wood boards and clap-boards, which were sledded over winter snows to Hartford and other distant towns. Whiteash sweeps, oars, and materials for ship-blocks were also got out and carried to Hartford and Wethersfteld for up-and-down river navigation of the Connecticut.
Dish-mills for making wooden bowls, trenchers, and mortars followed as accessories to the saw-mills. They used up the slabs from the saw-mill logs by cutting them into disks, which wei'e centred and turned in coarse lathes to the convex surface of the outer dish. With a curved turning-tool, the outer dish was separated from the disk, and then smaller ones were turned off .successively until the disk was exhausted. The slabs from which these disks were made were wider and thicker than were taken from logs when lumber increased in value. The trenchers and mortars were turned by a similar process. The maker or peddler of these articles packed them into a strong bed-tick, in which they were carried on the back of a horse, along the narrow bridle-paths, to the earlier-settled towns, where they were bartered for "store-pay." At least four of these mills were located along the lake stream, and as many others iu various parts of the town, in the last century, two of which - one at the Meadow Street crossing of the lake stream, and the other opposite the old lean-to mill-house on Lake Streets-were in operation as late as 1805.
Cheese-Boxes, Scale-Boards. - Early in this century John McAlpine erected and carried on a shop on the stream at the foot of the burying-ground hill, in Old Winchester, for making scale-boards, used for separating cheeses from each other when packed in casks for distant markets. As he enjoyed a monopoly of the manufacture in the centre of the dairy region of Connecticut, the demand for his article was extensive until the practice of packing each cheese in a separate box was adopted. This change necessitated the manufacture of round boxes, with covers, of sizes fitted to the various diameters and thicknesses of the cheese. This mode of packing went into vogue between 1820 and 1830, and was universally adopted as early as the latter year. One of the earliest manufiicturers of this article in Winchester was Silas H. McAlpine, whose shop on the Naugatuck branch is believed to be still in operation. Another establishment on Hall meadow, now owned by Nelson D.
Winchester
Ford, has been and is still in operation. These works were built in 1845 by Harvey Ford, father of the present proprietor, who ran it about ten years, and then put it into the hands of his two sons, one or both of whom have conducted the business until the present time. For the first five years there were from ten thousand to fifteen thousand boxes made up each year; since then some less, with variation from year 'to year. At present, and for the past few years, in addition to the cheese-box business, tliere is quite a business done in the saw-mill in coarse lumber. Another establishment was carried on in Winsted by Cook & Bacon, from 1842 to about 1846, in a shop adjoining the lake stream saw-mill.
Grist-Milh. - The two early grist-mills of the town have been already noted. The first was built by David Austin in 1771, near the lake outlet; the second, supposed to have been originally built by Elias Balcomb about 1776, stood on the, west side of Still River, immediately south of the stone bridge. It was owned and operated for many years by Ensign Jesse Doolittle, and was carried off by a flood about 1800, and was rebuilt by Samuel and Luther Hoadley about 1844.
Both these mills had three run of stones and were carried by permanent water-power. The Austin mill was rebuilt by the Rockwell Brothers about ISIO, and was finally burned down and abandoned in ISiJo. The Hoadley mill was abandoned by Riley Wiiiting about 182-'), and the brick-clock factory (burned down in 1870) was erected on its site.
Three or more feed-mills have come into existence witliin a few years: one owned by John G. Wetmore, opposite the Clarke house, another owned by Wing Persons, on Lake Street, and a third owned by Frederick Woodruff, on North Main Street.
Scythe- Works. - Until the closing part of tlic la.st century the scythe was, in this country, stri<-tly a hand-made tool, wrought out in smiths' shops by sledge and luunmcr, and ground on a stone turned l)y a hand-crank, or hung on the shaft of a flutterwheel, without gearing or other appliances. The Harris family, of Pine Plains and Salisbury, learned the trade of a negro slave purchased by their immediate progenitor from a former master who had taught him the trade.
The first establishment in the country for welding, drawing, and plating the scythe under trip-hammers by water-power, and grinding it on a geared stone, was erected by Robert Orr, of Bridgcwater, Mass., during or after the Revolution. The second establisliment of this nature was erected by Col. Robert Boyd, near the west bank of tlic Hudson, between New Windsor Landing and Newburg before 1790. Benjamin Jenkins, from Bri<igcwntcr, was foreman, and James Boyd, of New Windsor, was an apprentice in these works. They became brothersin-law, and in 1792 came to Winsted and erected the third establishment in the country on the site of the Winsted Manufacturing Company's present works on Still River. In 1802 they built another establishment on the site of the Winsted Hoe Company's platingshop on Lake Street, and soon after separated, Mr. Jenkins taking the original works on Still River, - from whom they have passed by successive conveyances to the present owners, - and Mr. Boyd taking the Lake Street works, and carrying them on, individually or with partners, until near the close of his life, in 1849.
77(6 Winsted Manufacturing Company was chartered May 6, 183-5. The annual production at beginning of lousiness was about five thousand dozen scythes, but the present annual production is ten thousand. Thirtythree men are employed. The present officers of the company are John T. Rockwell, President ; Joseph H. Norton, Agent and Treasurer; and Allen H. Norton, Secretary.
Merrit Bull, an early apprentice of Jenkins & Boyd, erected a scytlie-shoj) in 1802 or 1803, on the site of the present stone-shop, at the crossing of the lake stream by Meadow Street, which he managed until his death, in 1824, when the works went into the hands of S. & M. Rockwell, and formed the startingpoint of the large and prosperous establisliment built uj) and managed by the successive tirms of Rockwell & Hinsdale, Hinsdale & Bcardsley, Elliot Beardsley, and the Beardsley S<-ythe Company. This company was incorporated July 12, 1851, and the following were the first otTicers: Francis Brown, President; Elliot Beardsley, Agent, Secretary, and Treasurer. The present oflicers are Philo G. Sheldon, President; Edwaril P. Wilcox, .\gent, Secrotarr, and Treasurer. Number of hands employed, thirty-five; ca|>acity per month, one thousand dozen ; value of annual product, sixty thousand dollars.
Halsey Burr, an apprentice of Mr. Jenkins, built a scythe-shop in 1S14, near the site of F. Woodruff i^ Sons' feed-mill, on North Main Street, which he carried on in a small way until a few years before his death.
In 1831, Wheelock Thayer, previously a partner and acting manager in the scythe business of James Boyd ife Son, erected the scythe-works on Mad River, now owned by his daughter, and carried on by the Thayer Scythe Company.
The process of manufacturing scythes luut been from time to time greatly improvc<l by the invention of new machinery. The first of these in date and importance was a spring die, with attachments to tlie trip-liaramer for holding the back and setting down and smoothing the web of the scythe, - a very slow and laborious process when performed with the hand-hammer. The next improvement was, by a series of light tilt-liammers, to shape and tiuish the point; the next was a machine for turning and finishing the heel ; another was for spinning the straw rope for binding up the scythes in dozen packages, by a machine similar to the Dutch wheel and flyer for spinning linen. Most of these improvements have originated in Winsted.
Scythe-making was - with the exception of wooden ware - tlie earliest factory work carried on in Winsted, and has been uninterruptedly prosecuted to the present day, little impeded or accelerated by protective tariffs. The three establishments now in operation have a capacity for making two hundred and fifty thousand scythes per annum, and rarely fail of turning out tliat number.
Bar Iron and Blistered Steel. - Bar iron had been made directly from the brown hematite ores of Salisbury, Kent, and Amenia from time immemorial. In Litchfield County bloomery-forges stood on most of the available water-courses in nearly all the western towns. Tiiey furnished iron for three rolling- and slitting-mills, - one in Canaan, anotlier in Litchfield, and the third in Washington, where the iron was rolled and slit into rods for nail-making. These mills worked up only a small portion of the iron manufactured. Besides domestic uses of all kinds, it was largely made into anchors, which were sent to the seaboard.
Nearly all of these bloonieries, and all of the slitting-mills, have long since disappeared ; and their sites would mostly be forgotten did not the cinderheaps and imperishable charcoal-brays indicate their location. i
In 1795, Jenkins & Boyd, in company with Thomas Spencer, .Jr., erected the first forge in Winsted, on the water-]30wer of the Lake Street grinding-works of the Winsted Manufacturing Company.
In 1803 the Rockwell Brothers removed and put up their Colebrook forge on the site of Timothy Hulbert's present iron-works on the lake stream.
In 1808, James Boyd erected another forge on Mad River, immediately opposite the Clarke House ; and in that or the following year the Rockwell Brothers built another forge on the lake stream, below and adjoining the Connecticut Western depot grounds.
In 1811, Reuben Cook, in company with Ru-ssell Bunce and Charles Seymour, of Hartford, built the old Cook forge on Still River, where the axle-works of R. Cook & Sons now stand.
All of these forges manufactured refined bar iron from the best quality of Old Salisbury Ore Hill pig iron, for the supply of the United States armory at Springfield, which required the best iron the country could produce. If there was the slightest defect in the quality, the finished gun-barrel would reveal it by defective polish or failure to stand the proof of a double-test charge. Only a limited portion of the iron made could be brought up to these crucial tests by the best-skilled workmen. Iron of a slightly inferior grade was required for scythes, wire rods, and fine machinery. A still lower grade answered for the ordinary uses of country blacksmiths.
In the process of refining, the cinders drawn off through the tent-plate retained a percentage of iron nearly equal to the ordinary hematite ores. This was worked over in a chafery or bloomery fire, and produced a strong coarse iron, which was worked into tires, axle and crow-bar patterns, and plow-moulds, or into heavy shafting, saw-mill cranks, etc. Each forge had in connection with it a drafting-shop, with lighter hammers, to draw down the bars into rods and shapes of all kinds in demand, and especially to work up the refuse iron by welding to each piece an equal layer of blistered steel, and drawing the united masses into sleigh-shoes.
The iron and scythe business constituted the staple manufacturing business of Winsted until near 1840, when the government had settled its policy of importing its gun-iron from Norway ; the English had introduced better and cheaper iron of every form and size than heretofore; when the puddling process of ironmaking had grown up in more favored localities; when wood and charcoal had advanced in price, while transportation of raw material and manufactured articles - always a heavy burden - could no longer be endured. Under all these discouragements the iron manufacture rapidly died out. The lower Rockwell forge on the lake stream was converted into a scytheshop about 184-5. The Boyd forge, opposite the Clarke house, breathed its last about the same time. The upper forge on the lake stream lingered on until about 1850. The middle forge on the lake stream was sold by Elliot Beardsley to Timothy Hulbert in 1853, and was changed into a forge for puddling scrapiron, and is now conducted by the Hulbert Iron Company. The Cook forge, on Still River, about 1850 confined its operations to working scrap-iron into axle-drafts for finishing in the Cook Axle Company's works, of which the forge became a component part.
The consumption of bar iron in Winsted, instead of decreasing with the decadence of its home manufacture, has steadily increased. The new brands of Norway iron were found cheaper and better for scythes, hoes, and other articles than the costly home-made refined iron, and came into general use in our hardware manufactures. The scythe manufacture increased. The hoe manufacture was introduced, and soon consumed more iron than the whole scythe interest had required in 1830, and other new hardware manufactures took the place of the iron-forge.
Blistered Steel. - The first cementing steel-furnace in Western Connecticut was erected before 1800, in Colebrook, by the Rockwell Brothers, under the supervision of Mr. Jencks, an ingenious iron and steel worker from Taunton, Mass., which has been perpetuated to the present time, though rarely operated of late years. It was found that the Salisbury iron was deficient in the ingredient, whatever it is, that produces an edge-tool quality in steel. The steel produced has an elastic qualit}', fitting it for carriagesprings, hay- and manure-forks, and similar articles, and before 1850 was largely used for these manufactures, and likewise for sleigh-shoes and for general blacksmith work. Since 1850 the steels made from Swedish and Russian irons have nearly superseded the domestic irons, excej^t those recently made from spathic ores.
The second steel-furnace in this region was put up early in this century by Col. Abram Burt, in Canaan, Conn., and continued in operation but a few years. The third was erected in Winsted by James Boyd & Son, in 1832, on the site of Thompson's bakery, south side of Monroe Street, adjoining the bridge. It was designed for converting their own iron into steel, which they were then largely supplying to fork-manufacturers ; but was soon abandoned by reason of inducements held outby the Colebrook concern, making it more advantageous to have their iron converted there than to do it themselves.
Ciif NaUn. - Shingle-nails were cut from old hoops and headed by hand for the First Congregational meeting-house in 1800. The cutting-machine is supposed to have been worked by hand. Another machine for cutting shingle-nails from hammered strips of iron, by water-power, was started by .Tames Boyd about 18(18, and soon abandoned.
In 1810, Jesse Byington rented water-jiower from the old Jenkins scythe-shop proprietors, and erected a nail-factory a little south of the Winsted Manufacturing Company's scythe-works, in whicli he used a newly-inventc<l macliinc for cutting nails more accurate and uniform in size than \i\ the old hand machines, but without heading them. Before and during the war of 1812 he employed more men jis cutters and headers than were employed in any other branch of business in the place. After the return of ])eace, in 1815, and the introduction of the combined cuttingand-hcading macliine, Mr. Hyington's business broke down, and lias never since been resumed in any Ibrm.
Axes, - A.\e-making as a trade, distinct from otlier smith-work, was introduced here l)y Elizur Hinsdale in 1804 or 1805. He first had his shop on Lake Street, near the lake outlet, and in 18(l(i erected a shop on the site of the Foundry and Machine Company's works, wliicli he sul)se<|ucntly enlarged to a triphammer and grinding-works adapted siieciuliy to his business, which he prosecuted until near the close of 1819, when he failed, and the business wa.s abandoned.
About 1828, after the Collins a.\o-factory went into operation at Collinsville, Natiiaiiiel B. (iaylord, tlicn owner of the old Jenkins scylhc-works, entered into the business of axe-making under the supervijiou of
Marcus Morgan, an original worker in the Collins establishment. Mr. Morgan soon after purchased the works and prosecuted the business until 1832, when he sold out, and the Winsted Manufacturing Company now occupy the premises.
Iron M'ire. - In 1812, Samuel and Luther Hoadley and James Boyd erected a wire-factory on the west wing of the clock-factory dam, the first, or one of the first, erected in the country for breaking down iron wire from the rod and drawing it down to any size from a half-inch to a hair's diameter. The rods, of the very best Salisbury iron, were hammered down to a half-inch square, and then rounded by trip-hammer swaging-dies, and then, after successive annealings, were drawn down by " rippers," as they were called, to a size whence they could be further reduced by a continuous drawing around an upright block. It was the ripping operation, by self-acting pincers seizing the point of the wire at the plate, drawing it about eighteen inches, then letting go and sliding back and taking a new hold at the plate, and drawing another length, which was then new in this country. At that period there were few, if any, rolling-mills in the country that rolled out round rods suitable for wiredrawing.
The business was profitable, and was vigorously prosecuted until the close of the war, when foreign competition paralyzed it, and compelled its abandonment.
Lcnther. - In the last century, tlie regular shoemaker - as distinguished from tlic cobbler and catwhii)per^was also a tanner. He had his vats, uniler cover, in or out of doors, in which he tanned his own and his neighbors' skins, and made them into boots and shoes on the same premises with his tan-vats. Of these tanneries there were in the last century three or more in Old Winchester, to which the traveling currier jjcriodically resorted, and curried, or smoothed and softened, the sides of leather when taken from the vats. The oak bark, then solely used for tanning, had its outer surface sliaved off, and was then pounded or crushed under a heavy circular stone attached to a tenfoot shal\, .stationary at one end, ami rolled round a circle by a draft-horse, the bark being distributed along the circular track, and kept there by a man or boy with a rake. Two of these, owned respectively by the Wade and Blake families, continued in operation, by water-power and modern improvements, until about IS.'iO. Both are now abandoned. There was a like establisliment in Winsted, erected and owned by Elias Loomis, at the close of the last century, at the foot of " Dish Mill Hill," where the WoodrutV tannery now stands, which was abandoned many years before the present works were erectc<l.
About 1800 it was practically ascertained by trial that hemlock bark pos,se.s.ted the astringent and other properties requisite for tanning, and, in consequence, the business was thenceforward conducted on a larger scale in the Green Woods region.
Col. Hosea Hinsdale and Col. James Shepard came to Winsted in 1802, and erected a large tannery on Spencer Street, where now is the iash-pond of Engene Potter. The business was successfully prosecuted here by Col. Hinsdale until 1851, when he sold out to J. S. and J. T. Rockwell, and the business is now conducted by the latter.
In 1807, Col. Shepard solil out his interest to Col. Hinsdale, and, in company with Asahel Miller, erected the original tannery, on the site of the present tannery of George Dudley & Son. This establishment was owned and managed successively by Shepard & Miller, Abicl Loomis, and Alanson Loomis, until purchased by George Dudley in 1832.
In 1820 another tannery was erected by Horace Kanney, at the corner of North Main Street and the Cook bridge, taking its water-power from the west wing of Cook's dam, which was successively owned and managed by Kanney & Hawley, Norman S])encer, Jonathan K. Richards, Charles B. Hallett, and others, and was abandoneil as a tannery in 18.')7.
In 1821, Horace Ranney erected another tannery, on the site of the present Woodrutf tannery, on North Main Street, now owned by George Dudley & Son, which was successively managed by Lewis & Foster until 1834, by James A. Ayraiilt until 1841, since which it has been owned and managed by Frederick Woodruff until his sale to Dudley & Son, it having during his ownership been carried away by a flood, and afterwards rebuilt and enlarged.
The tannery business of Winsted has, since 1850, been confined to preparing sheep- and calf-skins for book-binding and similar purposes, and has become one of the prominent branches of our manufactures. The skins are imported from England, after having been split into two or more thicknesses, salted, and packed in hogsheads ready for the vat. The bark is finely ground in a mill in the second story of the building, and passed to a large receiving vat, where it is soaked in water until the tanning principle is extracted, when the liquor or tea, as it is termed, is drawn off into a line of receiving vats, and the exhausted bark is thrown out. A paddle- or flutter-wheel is fixed over each vat, and connected by gears with a line of shafting propelled by water-power. A sufficient number of vats are filled with the hemlock tea ; the right number of skins are thrown into each vat, and the flutter-wheels are set in motion and operate on the surface of the liquid, creating a current which keeps the skins in constant movement, and perfects the tanning process without hand-labor. The tanned skins are then smoothed, trimmed, assorted, and packed for market, the whole process requiring less than three weeks' time.
This branch of business was originated in Winsted by George Dudley, before 1850, in the works he purchased from Alanson Loomis in 1832. In 1853 he rebuilt and enlarged his works, and added two threestory buildings for dyeing the skins when tanned. In
In 1851, J. S. & J. T. Rockwell, previously engaged in this branch of tanning in Colebrook, erected the four-story tannery on the site of the Hinsdale premises. These works are now owned by John T. Rockwell.
Woolen Clotlis. - Joseph Piatt is believed to have been the first clothier in the town. He built a clothier's shop and fulling-mill in the Danbury Quarter between 1783 and 1787. The establishment had a brief existence. It is not mentioned in any deed on record, and its precise locality is unknown.
The first clothier in Winsted was Mr. Daniel Marshall, whose shop stood on Lake Street, as it then ran, nearly opposite the house at the corner of Lake and Rockwell Streets, and the fulling-mill in the rear on the lake stream. Mr. Marshall died in 1794, and Daniel Wilcox became the owner until his sale of the premises to the Rockwell Brothers, in 1813. A carding-machine was added to the establishment about 1804. The Rockwell Brothers, in 1813, erected additional buildings, and began the manufacture of broadcloths and satinets. The business was enlarged and vigorously prosecuted during the continuance of the war of 1812, and moderately thereafter until 1830, in the hope of making it a paying business, but with doubtful success. In 1835 the works were burned down, and never rebuilt.
About 1816 another clothier's works was erected by Ansel Wilson, on the site of the Strong Manufacturing Company's new factory. Chester Soper purchased this establishment about 1830, and a few years after erected a woolen-mill on the premises, in which be manufactured broadcloths until about 1838. The works were afterwards carried on by John Thornton and others until 1845, when the woolen business was abandoned and the building afterwards used for making joiners' tools.
Another clothier's works, built about 1814 on the Naugatuck branch in Old Winchester, and carried on by Alva Nash and others until 1828, when it was converted into a woolen-mill for making broadcloths and satinets by John M. Galagher, who failed within a few years, and was succeeded by Isaac Bird, who continued the making of satinets until the establishment went into the hands of the Winchester Centre Manufacturing Company, in 1854. This company confined its operations to making woolen knittingyarn until the establishment was burned down about 1860, and was never rebuilt.
The Home Manufacturing Company, a joint-stock concern, was organized in 1846, and the same year erected the factory building on Mad River now occupied by the New England Pin Company, and went into the manufacture of broadcloths and doeskins. It labored under the disadvantage of having no stockholders acquainted with the business, and was unfor- tunate in selecting overseers of the manufacturing department. No profits were realized, and in 1850 the concern was wound up. The establishment was sold to Anson G. Phelps, who operated it, in connection with his woolen-mills at Wolcottville, until 1852, wlien it was purchased by the Hartford Pin Company.
The William L. Gilbert Clock Company. - The manufacture of clocks, of which this establishment is an outgrowth or enlargement, was commenced here in about 1807, by Riley Whiting, for the manufacture of wooden clocks, for which Connecticut was formerly so famous. The manufacture of brass clocks wa.s begun in 1825. The first company organized was that of Clarke, Gilbert & Co., then William L. Gilbert c% Co., later the Gilbert Manufacturing Company, and the present company, the William L. Gilbert Clock Company, which was organized in 1871 with a capital of one hundred thousand dollars, with William L. Gilbert president, and I. B. WoodrufT secretary and treasurer.
In 1871 the works of the company were destroyed by fire, but by the energy and enterprise of the proprietors they were immediately rebuilt. The reputation of the goods of this house was such that the demand required more extensive facilities for their production before the works were destroyed by fire; consequently, availing themselves of the opportunity of making improvements in rebuilding, tiic new premises were much enlarged, making them more commodious and far better adapted for tiie desired purpose. The establishment is supplied with all modern improvements, and is complete in all its appointments. They manufacture a large variety of clocks, and at present are making a specialty of fine regulators, set in elaborately and richly-carved cases. The clocks produced by this company are unexcelled for beauty of design, style of finish, quality of material and workmanship, and real merit as timekeepers. The salesrooms of the company arc located at New York City, Chicago, 111., and Gla.sgow, Scotland, and are under the management of Mr. tJeorgc B. Owen, who has been connected with (and interested in) this business since 1866. Mr. I. B. AVoodruff, the secretary and trea.surer, has been connected with and closely identified in the management of the business since 1851, a period of thirty years, during which tlie factories h.ive never been closed except for purposes of inventory and repairs.
Car<U. - -Vt the beginning of the war of 1812, two establishments for making hand- and machine-cards were started, one by Coe, Miller & Co., in the Shcpnrd & Miller tannery, and the other by the Iloadley Brothers, in their grist-mill. Both companies used one set of machines for cutting and bending the teeth, and another set for pricking the leather, and tlic teeth were inserted in the leather by children at their homes.
Other machines shaped and turned the handles, on which the hand card-leathers were fastened by tacks. Two causes put an end to this branch of manufacture, - one, the return of peace in 1815 and the influx of cheaper cards from England, and the other, the invention by Mr. Levi Lincoln of a combined machine, which in one operation pricked the leather, cut and bent the teeth, and stuck them through the pricked leather.
Wagons and Carriages. - There were, doubtless, wheelwrights and wagon-makers in Old Winchester at an early day, but the compiler has no knowledge of them. Randall Covey had a wagon-maker's shop at the Centre from 1817 to 1821.
Joseph Mitchell was probably the first wheelwright in Winsted. His house and shop, now torn down, were directly opposite the residence of Sheldon Kinney, on Main Street. He made cart-wheels and bodies from the beginning of the century, or earlier, to about 1830.
Selden Mitchell, son of Joseph, above, made light wagons in the basement in rear of the Kinney house above mentioned from 1809 to about 1820.
In 1813, Shubael Crow and Ebenezer R. Hale erected a carriage-maker's shop on the site of John T. Rockwell's tannery, in whicli wagons and chaises were made until after 1830 by Crowe & Hale, Crow & Bandie, Henderson & Ball, and others, - the premises having been used from 1823 to 1826 for numufacturing pails, tubs, and keelers by Hinsdale and Dimock.
Wagon-making wiis subsequently carried pn in Winsted by James Hermance from 183S to his death, in 1840, and by (J. W. Giuston from 1849 onward to 1872.
In 1851, Walter & Son erected a large carriage-shop on the corner of Elm and Centre Streets, which lia.s since been managed successively by Erwin JI. Walter, Uriah S. Walter, W. H. Stickney, and Eranklin Lincoln, and is now owned and managed by Joseph F. Lincoln.
In 18.56 the Winsted (joint stock) Carriage Company wiLs organized, and carried on a large business in Southern wagons and buggies until the opening of the war of the Rebellion, occui)ying the old Soper woolen-factory. In 18(!6 the company was reorganized with a reduced capital, and Marcus Bird, Walter Stickney, Wni. S. Holabird, and others as stockholders, and was wound up in 1867.
The (filliiuin Carriage Company was organized with a capital of twenty-five thousand dollars in 18G7, and purchased the factory jiroperty of the Winsted Carriage Company; and soon after, on the burning down of the factory building, erected a spacious establishment on the same site with facilities for a large business. This establishment was burned down in 1870, and the operations of the company were tliereby suspended.
An oil-mill was erected by Bissell Hinsdale, on Mad River, a little west of the Clifton Mill works, about 1816, which was worked only a few years, and was removed before 1830.
Tlie spring steel hay and manure forks were introduced as a substitute for the coarse and clumsy articles previously in use soon after the war of 1812. They were made here in numerous small shops by handicraftsmen, no machinery save the sledge and handhammer, propelled by muscular arms, being used. Large quantities were made, not only for supplying the country stores, but for the New York and Philadelphia markets. The three Browns, - Orrin, Harris, and Isaac, - Oliver White, Julius Weaver, and others were engaged in this business. Establishments grew up in other places in which the tilt-hammer came into use for drawing out the tines, which made the handlabor operation uuremunerative, and the business was, in a great measure, abandoned here about 1850.
Foundries. - The casting of iron clock bells was begun in Winsted by the Hoadley Brothers, about 1810, l as a secret process, in a detached building, from which outsiders were rigidly excluded. The skilled founder of the establishment ran away after some two years' service. In 1812, Nathan Champion commenced the same business in the Jenkins scythe-shop, that stood ou the Strong Manufacturing Company's premises, and afterwards built a shop near the Winsted Manufacturing Company's works, in which he made other small castings.
In 1834, Nathaniel B. Gaylord erected a foundry on the site of the Strong Manufacturing Company's works for casting stoves, plows, gears, and general custom-work, which he operated until 1846, after which it was carried on a short time by Calvin Butler, of Canaan, and was then abandoned.
In 1847, Taylor & Whiting erected a foundry in connection with their machine-shop, now owned and operated by the Winsted Foundry and Machine Company, which is now the only eitablishment in the borough.
In 1853, John Boyd erected another foundry for large castings in connection with his machine-shop, adjoining Lake Street bridge, on Mad River, which was discontinued in 1854.
Mac/iine-s/iops. - In 1831, George Taylor erected the original building of the present Foundry and Machine Company's establishment on Main Street, for making woolen machinery as a si^ecialty, and doing general job-work in that line. Two years later he associated with Ambrose Whiting as a partner, in the name of Taylor & Whiting. They did a large business in carding-machines and spinning-jacks for some twenty years. After the retirement of Mr. Whiting, in 1857, the concern was organized as a joint-stock company, with the name of The Winsted
In 1823, James Boyd and James M. Boyd began making saw-mill cranks, mill spindles, and various other branches of heavy forging in a shop then built on the west side of Mad River, in rear of the Beardsley house. To this business James Boyd & Son added, in 1830, the making of finished coach-axles and millscrews. In 1851, after the death of Mr. James Boyd, the junior partner erected the present macliine-shop on the site of the old shop, for the purpose of enlarging the mill-iron and axle business of the old firm, and in 1853 built the foundry last referred to as an appendage to the establishment. The works were purchased by the Clifton Mill Company in 1857, and were a few years after employed in the manufacture of monkey-wrenches. Wing Person's feed-mill now occupies the site.
Reuben Cook, deceased, the head of the firm of R. Cook & Sons, began making iron in 1811, on the site now occupied by the axle-factory, and had for a time associated with him the late Russell Bunce and Charles Seymour, of Hartford. The iron used was made from the red or hematite ore from the mines at Salisbury, Conn., which mines were worked during the war of the Revolution. The pig iron was hauled across the county thirty miles to Winsted, where it was made into refined iron, which was carried thirty miles farther to Springfield, Mass., where it was made into guns. About one-third of the entire product, not being quite flue enough for gun-barrels, was made into tires, crowbars, sleigh-shoes, plow-molds, and mill-cranks.
In 1825, over half a century ago, Mr. Cook began making axle-drafts. At that time the arms were forged eight-sided by a trip-hammer with a straight die, and were made round as nearly as possible by the blacksmith who bought them. He continued making drafts in this manner until 1832, when he began to swage the arms of the axle round under the hammer, and was the first to adopt that improved method. In the same year he built a shop in addition to the forge already in use, and made mill-irons, cranks, etc. The business increased moderately, and improvements were continually made, and in 1839 the present firm was organized and the axles were entirely finished on the premises. This makes the firm the oldest in the country that is still doing business without change of name. The works have been trfice destroyed by fire, once in 1852, and again in 1871, but were immediately rebuilt.
The firm of R. Cook & Sons has always endeavored to keep up with the times as its founder had done from 1811, when but a very young man he started in business against very sharp competition from other parties in the same town, who have long since gone out of business life, and some of whom arc deacesed.
Carpenters' Tools. - About 1828, Samuel Boyd engaged in the manufacture of steel hoes and shovels, and erected the original buildings of the Clifton Mill Company works on the south side of Mad River. He also manufactured in these buildings nail-hammere, socket-chisels, aud draw-shaves until 1833, when the business was discontinued.
The Wiiisfed Hoe Company. - In 1852, John Boyd, Louis E. Boyd, and Daniel B. Wheelock began to manufacture planters' hoes for the Southern market in the brick scythe-works at the corner of Lake and Meadow Streets. It was a new business and encountered serious difficulties, one of them being the anti-slavery proclivities of the first and third partners, of which the Southern customers were duly notified by competing manufacturers. The obnoxious partners withdrew from the concern, and it became a decided success under the name of " The American Hoe Company." The hoes became the leading article in the market. They were sent to England and duplicated as to the style and finish by English manul'acturers, but their work jjroved inferior in working quality.
The establishment was enlarged by the erection of grinding and polishing works on two other waterpowers, and in 1855 employed more hands than any other concern in the borough. The business waa prosecuted with much energy and fair success until the breaking out of the Southern Rebellion in 1S()1. Tlie war closed the market, and so closed tlie shops. They remained closed until peace returned in 18G5, when Mr. T. M. Clarke - who for twelve years previously and from its commencement, with one short interruption, had edited and published the Winstcd Herald - organized the Winsted Hoe Company, and as its president and principal manager revived the business. Under Mr. Clarke's management tlie business lias been largely increased by the addition of new branches, - more especially the manufacture of edgetools, - and in the extent of its business and in financial strength the Winsted Hoe Company now ranks among tlie first in Litclifield County.
Thr T. C. liichardK li: Co. Iliirdware Manufacturing Comjxini/ is also located in West Winsted. This is one of the representative institutions of the town, and is under the efficient management of Mr. T. C. Richards.
Bolts and Nuts. - The Clifton Mill Company, soon after the purchase of Samuel Boyd's works on the south side of Mad River, engaged in the inaiiufucture of nuts and washers, and about 1855 added carriagebolts and nuts to its otiier manufactured articles, adding for that purpose the three-story btiilding on their premises, and also the Boyd maciiinc-shop at tiie foot of Lake Street. On the i)urcliase of their works by the Winsted Hoe Company, the nut and bolt manufacture was discontinued.
Another carriage-bolt manufacture was started on the premises of B. Cook & Sons by Franklin Moore and Edward Clarke about 1867, which is still in active and successful operation, under the ownership and management of Alfred E. Moore, son of Franklin Moore, deceased.
Table Cutlery. - \n 1852 the " Eagle" works, a jointstock company with a capital of twenty-five thousand dollars, was organized and put in operation under the supervision of Albert Bradshaw, an English cutler, in a brick factory building on the lake stream, adjoining the Connecticut Western depot grounds. The business not proving successful, operations were suspended about 1854, and in 185G the establishment was purchased by Rice, Lathrop & Clary, under whose ownership the brick factory building was burned down, and a smaller wooden building was erected on its site; and soon afterwards the auger-factory building on Mad River, near the corner of Main and Coe Streets, was purchased. This building was burned down and rebuilt about 18tj6. Mr. Clary died in 1861, and Mr. Rice retired from the concern in 1862. George F. Barton came in as a partner with Mr. Lathrop in 1864, and retired from the partnership in 1872, leaving Mr. Lathrop the sole owner.
Pocket Cutlery. - In 1853, Thompson & Gascoigne (Englishmen) carried on a small pocket-cutlery business in the factory of the Eagle Company, which was soon after taken up by Beardsley & Alvord, and gradually enlarged and made profitable. In 1S5G they built their cullery-works at the lake outlet, and have since transacted a large and prosperous business in the name of " The Empire Kiiil'e Com|)any." In 1880 the concern was moved to the present site, formerly occupied by the table-cutlery establishment of William P. Lathrop.
In 1854, C. F. Clark, an Englishman, started a pocket-cutlery concern in the attic of the Cook axlefactory, which was taken up by Horace I'lielps, and after a trial of one or two years was abandoned.
Auyert. - The Winstcd (joint stock) Auger Company was organized in 1853, with a capital stock of ten thousand dollars, and immediately after erected the factory on Mail River, near the corner of Coe and Main Streets, at a cost beyond their cajiital. It was managed inefficiently by men unac(|uaintcd with the busincMS, and was wound up before 1860.
Piiu.* - In 1852, Erastus S. Woodford, J. B. Terry, and others organized "The Hartford Pin Company" (joint stock), and purchased of Anson G. Phelps the woolen-factory building on IJridge Street, opposite the Naugutuck Railroaddepot grounds, and began making pins the same year. The company at once cnnie into conflict with the Howe Pin Comjiany, of Biriningliam, in respect to a i>atented sticking-machine for sticking the piiia on paper, which impeded operations until the question of infringement was settled by litigation in the United States Circuit Court. In 1857 the factory property and machinery of the company became the property of James R. Keeler, who conveyed the same to " The New England Pin Company," organized in May of the same year, and composed of said Keeler, Hector Armstrong, C. O. Crosby, and John G. Wetmore, stockholders, and with a capital of one hundred thousand dollars.
The Wyoming rin Company was organized in March, 1880, with Mr. T. S. Carroll president and secretary. The manufacture of pins was commenced in September, 1880. The establishment was burned in January, 1881, and started again in March following. The factory emijloys twenty-two persons, and has a capacity of one million and eighty thousand pins daily. Mr. Carroll is also the manufacturer of a champagne tap, upon which he has a patent now pending.
Steel Firc-Irons. - Benjamin and Edward Woodall (Englishmen) began making, of highly polished steel, shovels and tongs and other fire-irons, about 1850 ; and in 1854 organized the " Winsted Shovel and Tongs Company," under the agency of Justus R. Loomis ; they bought the Halsey Burr scythe-shop and water-power, and erected the factory building now used as a feed-grinding mill by Frederick Woodruff, on North Main Street. The concern lacked capital, energy, and business skill, and was closed up about 1857.
TIte Winsted Plane Company, organized in 1851, entered on the manufacture of joiners' tools in the old Soper woolen-factory building, and continued until about 185(5, when it became insolvent and was wound up.
The Clifton Lumber Company was organized in 1854, and erected the building near the Naugatuck depot, now occupied by the Winsted Printing Company, for planing lumber and manufacturing doors, sashes, and blinds by steam-power. The concern was wound up in 1857.
Another company or partnership, consisting of Ralph H. Moore, Franklin Moore, and others, in 1872 erected a factory on Case Avenue for making plated spoons and other plated articles. This establishment was destroyed by fire in 1873.
The Borden Condensed Milk Company, consisting of Gail Borden, Theron Bronson, and Elhanan W. Tyler, was organized in 1863, and purchased the factory building near the Naugatuck depot, now occupied by the Winsted Printing Company, in which they condensed milk until 1866, when, not finding the location favorable for the business, the concern was wound up.
The Henry Spring Company, located at West Winsted, was organized at New Haven in 1869, and its location was transferred to Winsted in April, 1870, and the grinding-shop on Lake Street, erected by the American Hoe Company, was purchased by the Spring
Company, and its machinery placed therein. The spring made by them is a patented article, combining equal strength and elasticity with springs of other manufacture of a third more weight, and are in constantly-increasing demand for light buggies and carriages.
The Winsted Paper Box Manufactory, R. L. Preston proprietor, is the only institution of the kind in town, and greatly merits its present success. The manufacture of tin-, brass-, and copper-ware is also carried on extra.
The Winsted Gas Company was organized Oct. 15, 1860, with a capital stock of twenty thousand dollars, nearly half paid in, and directors were appointed as follows : George Dudley, Erastus S. Woodford' Moses Camp, Elliot Beardsley, Caleb J. Camp, Jabez Alvord, John Hinsdale, James R. Alvord, and Henry Gay.
A small gas-works was erected in 1861 on Prospect Street, and continued with varied success until April, 1874, when the company was reorganized with a capital of sixty thousand dollars, the old works abandoned on Prospect Street, and new fire-proof brick works erected on Case Avenue, and main iron pipes relaid, much larger than before ; also extended to the East village (so called), and through North Main Street to Cook's.
The directors elected at the reorganization in 1874 were Henry Gay, George Dudley, Caleb J. Camp, Edward R. Beardsley, Edward Clarke, J. M. Loweree, Harvey L. Roberts, Henry G. Colt, George W. Phelps.
At a directors' meeting, held April 24, 1874, Henry G. Colt was elected president, and Sidney F. Dickerman secretary and treasurer. The same efficient officers have continuously had charge of the works since its reorganization; but time's changes have necessitated changes in the board of directors, which in May, 1881, are as follows: Henry G. Colt, H. H. Tibbals, Edward R. Beardsley, Sidney F. Dickerman, Henry Gay, Rufus E. Holmes, T. F. Rowland, Harvey L. Roberts, and Edward Clarke.
Provenance
Text from History of Litchfield County, Connecticut, published 1881, in the public domain in the United States and digitised by the Internet Archive.