Jet Propulsion Laboratory Edwards Facility, Edwards Air Force Base, Boron
Jet Propulsion Laboratory Edwards Facility, Edwards Air Force Base, Boron, Kern County, CA. Surveyed as HAER CAL,15-BORON.V,1-, with a 62,920-word written history.
From the record
“Operated by the California Institute of Technology, the Jet Propulsion Laboratory Edwards Facility was the United States' first university-sponsored research and testing facility for the development of liquid-fueled rocket engines and components.”
Written record, HAER CAL,15-BORON.V,1- survey. Machine-read text.
Surveyed by the federal HAER program as HAER CAL,15-BORON.V,1- · the record runs 62920 words · one of 136 surveyed structures published for this county.
Source document
Quoted word for word from HAER CAL,15-BORON.V,1-.
Not written, edited or summarised by this site.
Edwards Air Force Base Boron vicinity Kern County California UTM coordinates of property line: and USGS 7.5 min Edwards quadrangle, and USGS 7.5 min North Edwards quadrangle, and USGS 7.5 min Rogers Lake North quadrangle, Dates of with major construction programs in Construction: and Modifications to facilities occurred on a more frequent basis into the Fabricator: United States Army Corps of Engineers; numerous private sector contractors thereafter. Edwards Air Force Base Boron Vicinity Kern County California UTM coordinates of property line: and USGS 7 .
5 min Edwards quadrangle, and USGS 7.5 min North Edwards quadrangle, and USGS 7.5 min Rogers Lake North quadrangle, Date of Modifications to facilities Construction: occurred on a frequent bas~s in the Fabricators: Greyna1d Construction of Sherman Oaks, California and the Ruane Corporation of San Gabriel, California.
Significance
60252 words
The headings the report itself prints. Each one jumps to where it begins.
Source document
Quoted word for word from HAER CAL,15-BORON.V,1-.
Not written, edited or summarised by this site.
Operated by the California Institute of Technology, the Jet Propulsion Laboratory Edwards Facility was the United States' first university-sponsored research and testing facility for the development of liquid-fueled rocket engines and components. It became a primary national test facility. Experimental liquid propellant combinations were evaluated here, and later solid fuel rocket motors were built and tested here (including motors for the Space Shuttle). It was the site for testing interplanetary space probe engines for noted programs such as Pioneer, Ranger, Surveyor, Mariner, Voyager, and Viking. Historians: Primary: Scott M. Hudlow, Architectural Historian, Computer Sciences Corporation, Edwards Air Force Base, California Secondary: Richard K. Anderson, Jr. Columbia, South Carolina.
December 1994-May
Jpl Edwards Facility
Edwards Test Station) HAER No. CA-163 (Page 2)
Table of Contents
Historical Background and Context 4 pioneering People 4 Beginnings of The GALCIT Project 10 Testing Missiles for the Army . 15 Corporal Rockets and Test Stand "A" 20 Sergeant Missile 24 Deep Space: The Next Frontier 25 The Ranger Spacecraft 30 The Mariner Spacecraft Viking and Voyager . Closure of JPL Edwards Facility 32 35 37 JPL Test Stands and the Industrial Cultural Landscape 38 Site Characteristics . 40 Initial Construction: Test Stand "A" 44 Test Stand "A" Ancillary Structures 48 Test Stand "B" . . 51 Test Stand "B" Ancillary Structures 54 The Tunnel System 56 Test Stands "C" and "D" and Their Complexes 58 Test Stand "E" and the Solid-Propellant Processing Line 95 JPL Glossary 104 Acronym List 106 JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 3) Chemical Names and Formulas 108 Project Information . 110 Illustration Sources 113 Bibliography 115 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 4) Historical Background and Context The Jet Propulsion Laboratory dates from It originated as part of the applied mechanics program at the Guggenheim Aeronautical LaboratorY/California Institute of Technology (GALCIT). six student scientists led by Hungarian emigre Theodore von Karman conducted the first static tests of uncooled liquid-propellant rocket engines in in the Arroyo Seco, located at the western edge of the San Gabriel Mountains in Pasadena, California.
The Arroyo Seco was chosen for its relative isolation from urban development, lack of foliage, and proximity to the California Institute of Technology (Cal tech) campus in Pasadena. ' GALCIT was an early, amateurish rocket project.' Caltech has since received recognition as the first university in the United States to sponsor formal rocket research. Theodore von Karman and his six student scientists (Hsue Shen Tsien, Apollo M.O. Smith, John W. Parsons, Edwards S. Forman, Weld Arnold, and Frank W. Malina); Robert H. Goddard; and the exiled German rocket scientists led by Wernher von Braun who worked for the Army after World War II (WWII) at White Sands, New Mexico and later at Redstone Arsenal, Huntsville, Alabama can each claim the seminal roles in America's space program.
Pioneering People Research into rocketry began well before The Chinese first used primitive rockets in the twelfth century, probably using black powder as a propellant. Clayton Koppes wrote that in the 19th-century, "Europeans later adapted them [rockets] for warfare-Francis Scott Key scribbled 'The Star Spangled Banner' in the immortal glare of Congreve's incendiary rockets. But these nineteenth-century specimens were inaccurate and dangerous and fell into disuse when improved artillery became available.'" Although, early examples of interest in rocketry are known, the 1 Daniel, Mann, Johnson, and Mendenhall. Master Facilities Plan Report on file at JPL Edwards Facility, Edwards AFB, California, unpaginated; and Clayton R.
KoppeS, JPL and the American Space Program: A History of the Jet Propulsion Laboratory. New Haven, Connecticut: Yale University Press, 2 Koppes, 3 Koppes, 1. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 5) modern origins of rocket research and interest in space travel date to the early 20th-century. In their respective countries, three distinct individuals are most responsible for establishing the theoretical and practical basis for research into rockets and missiles. A Russian, Konstantin Eduardovich Tsiolkovsky, published a theoretical essay on space travel in Hermann Julius Oberth, a Romanian living in Germany, wrote an important, exhaustive, theoretical analysis in Robert H.
Goddard, an eccentric New Englander, flew the first liquid-propelled rocket in Rocketry was first researched by Konstantin Eduardovich Tsiolkovsky, who could be considered the father of rocket science. He was a quiet, studious physics teacher and theoretical philosopher, who never flew a single rocket in his lifetime. Yet, Tsiolkovsky recognized four basic principles of rocket flight. First, reactive thrust is the key by which to achieve motion or acceleration in a vacuum. Second, the measure of thrust is achieved by the exhausted gases. Third, the speed reached by a rocket depends on the temperature of the combusted gases and the weight of the gases' molecular constituents. Last, Tsiolkovsky understood staged propulsion and the understanding of thrust-to-weight ratios. Tsiolkovsky: By ...
was describing the principles of a throttlable rocket motor and, just two years later, wrote a book which prophesied the advent of earth orbiting satellites. After spending more years in defining the concept he finally prepared a paper, at the age of forty, entitled Exploration of Outer Space with Reactive Devices. Tsiolkovsky led a peaceful life with little thought for the mechanics of war and to him the great dream of space travel could be transformed into reality. Repeated calculations convinced him of this possibility and in at the age of forty six he described in detail how a rocket device could be made to transport men beyond the atmosphere using liquid oxygen and liquid hydrogen. 5 Tsiolkovsky believed that if two liquids could be brought Baker, David.
The Rocket: The History and Development of Rocket & Missile Technology. New York, New York: Crown Publishers, Inc., 22. 5 Baker, 17. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 6) together in a chamber and ignited, the resulting gases could be channeled through a narrow orifice at the rear and propel the rocket and a payload in the opposite direction. The gases would expand and be exhausted at high velocity, which would initiate the reaction. Tsiolkovsky was theoretically correct, Moreover, he speculated that to reach a speed of 8 kilometers per second the device must carry propellant weighing four times the empty weight of the rocket and its cargo. Significantly, a velocity of 8 kilometers per second is the speed necessary for orbital flight.
Tsiolkovsky recognized the difficulty inherent in this requirement, the huge size and thrust of the rocket necessary to achieve orbital flight. He proposed the use of a staged rocket whereby successive sections could be jettisoned as the propellant was exhausted. 6 Hermann Oberth, a Romanian, is considered the father of German rocketry. A Versailles Treaty provision prohibited the Germans from developing artillery. The Germans perceived this proscription as an opportunity to develop rocket and missile technology. He wrote a thesis on spaceflight and attempted to publish the text. In when Oberth agreed to underwrite some of the expenses, The Rocket into Interplanetary Space appeared as a bodk.
A second edition of his book appeared in under the revised title The Road to Space Travel, which won Oberth a 10,OOO-franc literary prize. The award funded his liquid propulsion research. 7 The Rocket into Interplanetary Space spurred open public interest in rocket transportation. In amateur German space travel and rocket enthusiasts organized the Verein fur Raumschiffahrt , or the Society for Space Travel. The founding of the Society for Space Travel brought a veritable barrage of interest and enthusiasm in space travel. Membership in the VfR grew to several hundred persons, accompanied by publication of several new books on the subject. In Max Valier, a popular space writer, eager to exploit the new technology, put solid propellants on the back of a modified automobile.
In a series of runs, each one using modifications dictated by the lessons of the preceding test, Valier reached speeds of up to 100 miles per hour, and attracted considerable public interest in the process." 6 Baker, 17. 7 Baker, 27. 8 Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 7) The VfR moved to a suburb of Berlin; an abandoned ammunition dump provided them with a proving ground for rocket tests. Many young enthusiasts were associated with the VfR experiments, including wernher von Braun, Willy Ley, and Hermann Oberth. By Oberth was working to prepare his first rocket, which was never launched.' The next year, Oberth and the VfR prepared a small liquid-propelled rocket, using gasoline and oxygen as fuel and oxidizer.
The combustion chamber protruded into the liquid oxygen tank to facilitate cooling. The rocket, Mirak 1, was unfortunately destroyed during ground tests before flight trials commenced. Several months later, its successor, Mirak 2, demonstrated 75 pounds of thrust; however, the tiny motor exploded before it could be test launched. Shortly after these abortive efforts, Oberth's concerted efforts paid off. Johannes Winkler launched a liquid oxygen/liquid methane rocket on a successful ascent from Dessau on 14 March which was the first liquid-propellant rocket flight outside the United States and the sixth in world history. 10 In the Hermann Oberth laid the groundwork for the Nazi missile program.
Oberth was one of the principals in establishing Peenemlinde, the Nazi Germany rocket testing facility on the Baltic coast. It has been suggested that Oberth helped the Nazis select the site; this section of the Baltic coast contained Oberth's original site for his rocket test. Peenemunde was also the area where Johannes Winkler wanted to conduct his rocket testing. Oberth has also been credited as leading the Peenemunde facility and developing the German WWII liquid-propelled V-2 rocket. 11 The primary pioneer of American rocketry was Robert H. Goddard. He received his in Physics in from Clark University in Worcester, Massachusetts, where he later taught physics. Goddard is considered the father of American rocketry, and was the world's first practical demonstrator of rocket power.
Spurred by design progress, he immediately began preparing a set of papers demonstrating the feasibility of liquid propulsion systems. By Goddard had applied for and been granted , Ley, Willy. "V.2-Rocket Cargo Ship", reprinted in Famous Science-Fiction Stories: Adventures in Time and Space. Raymond J. Healy and J. Francis McComas, eds. New York, New York: The Modern Library, 10 Baker, 28. 11 Ley, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 8) patent licenses for a host of devices related to rocket engines, including a combustion chamber design, a propellant feed and control system, rocket nozzles (expansion chambers) and a multistage rocket which would carry a second stage within the upper frame of the first stage.
" Goddard typified the scientific efforts in the early twentieth-century, before the advent of government funding and the modern laboratory. 13 He worked alone- a stereotypical eccentric inventor. In many respects, Goddard occupies a place in the history of rocketry similar to that of Samuel Langley, the Wright Brothers, or Glenn Curtiss in the history of flight. ' In the Smithsonian Institution published Goddard's classic paper entitled A Method of Reaching Extreme Altitude. It detailed, " ... the feasibility of building rockets propelled by successive impulses from powder engines that might reach the moon. This work clarified Goddard's innermost desires and prompted a measure of introspection and withdrawal, which remained with him for much of his life.
A Method of Reaching Extreme Altitude was based on the work Goddard had undertaken up to America's entry into World War I, including studies conducted in the Arroyo Seco, near future location. The essay carried definitive values for a rocket design required to perform a limited demonstration and introduced a much more ambitious proposal, reaching the moon. Goddard recognized the problems associated with accurately measuring the altitude that could be reached by successively higher rocket trajectories. He felt it would be a good idea to set off a small explosion by means of "flash powder" so that ground instruments could register the height reached by the projectiles. Goddard acknowledged this would of course be difficult to accomplish.
He noted that the angle of the rocket's 12 Baker, 13 Noble, David. America by Design: Science, Technology, and the Rise of Corporate Capi talism. New York, New York: Oxford University Press, 14 Hudlow, Scot t M. CuI tural Resource Eval ua ti on of the North Base Complex (The Muroc Flight Test Base and the Rocket Sled Test Track), Edwards AFB, Kern County, California. Report on file at AFFTC/EM, Edwards AFB, California, 15 Koppes, 2. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 9) ascent would be difficult to predict, and that glare from the Sun would compromise satisfactory observation of the flash.
To escape this quandary, Goddard suggested that a rocket should fly to the Moon while it was between the Earth and the Sun so that the rocket could impact the lunar surface, set off the powder flash, and provide a visible light source against the darkened background. As David Baker states concerning A Method of Reaching Extreme Altitude: In one move he [Goddard] had shown that the only way to demonstrate the rocket's potential satisfactorily would be to send it to the Moon, and in doing so ably provide the world with proof of the important developments which could result from such experiments. Concluding the report, Goddard admitted that the plan had little scientific merit, but that the flight could lead to more important tests which would carry scientific instruments into space.
This latter possibility was only hinted at and this was undoubtedly because few who were not directly associated with rocket development could see any real long term value in the device. Nevertheless, Goddard had provided an exciting idea for those who had the foresight to see it and the report serves as a reminder that he was ever concerned about the rocket's potential, although the rest of his life would be devoted to engineering developments of more short term interest. '6 In the mid Goddard began experimenting with rockets to implement his theories. In December he successfully ran a rocket motor for 24 seconds before the rocket expended its propellant supply.
Additional tests, in January had a similar successful outcome; the rocket device rose as high as it could in the restrained test stand. Independent flight was the next stage. Robert Goddard attempted a flight test on a farm at Auburn, Massachusetts, just outside Worcester. Tests began in March of Goddard was ready to demonstrate a free flight. Goddard placed the rocket in a 6-foot tall A-frame on 16 March Four assistants helped him; his wife took notes. The liquid oxygen and gasoline propellants ignited and the rocket lifted into the air. The flight was over in 2.5 seconds, yet in that short interval, the rocket had accelerated to an approximate height of 40 feet with an average speed of 60 miles per hour.
The rocket landed approximately 181 feet away from the test stand, in a cabbage patch. The world's first free flight of a 16 Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 10) liquid propelled rocket had been successful. A second flight, lasting 4.2 seconds, followed several weeks later. Goddard, spurred by his successes, went back to the drawing board hoping to add refinements which would improve the performance of the basic design." Three years later, Goddard tested a second rocket. In he left Massachusetts for the solitary expanse of New Mexico. 18 Beginnings of The GALCIT Project The GALCIT group, formed in contacted Goddard to consider joining forces. Not given to teamwork, Goddard developed a paranoid fear of competition.
He was especially wary of students, whom Goddard thought were trying to steal his inventions. Homer Newell states: Members of the California Institute of Technology Rocket Research Project, established in by Theodore von Karman, director of the institute's Guggenheim Aeronautical Laboratory, tried to persuade Goddard [in to join forces with them. When i t was stipulated that a partnership would require mutual disclosure of ideas and projects, Goddard shied away. His reluctance to work openly with others deprived Goddard not only of the opportunity to provide leadership in the field, but also cut him off from the professional assistance that he might have received from experienced engineers who could have helped put his many ideas into practice.
' His secrecy and caustic spirit isolated him and deprived him of desperately needed help, whereas the GALCIT/JPL enjoyed the team spirit necessary to modern industrial research and development, which is characterized by the laboratory concept. 20 As GALCIT made theoretical and financial advancements in the late and into WWII, Goddard's star sank. Without the engirieering expertise necessary to overcome obstacles in pursuit 17 Baker, 24. 18 Koppes, 2. 19 Newell, Homer E. Beyond the Atmosphere: Early Years of Space Science. Washington, National Aeronautics and Space Administration, 20 Noble. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (page 11) of his dream of spaceflight, Goddard slipped into obscurity during WWII, winding up working at a naval research station on a JATO (Jet-Assisted-Takeoff) project. He died in National Aeronautics and Space Administration (NASA) posthumously awarded his estate in for the rights to the myriad of patents he held. Further, NASA renamed the Naval Research Laboratory the Goddard Space Flight Center in his honor. Hungarian emigre Theodore von Karman led the GALCIT's rocket program. Von Karman, a brilliant aerodynamicist and theoretician, received his from Berlin University. He taught briefly in Hungary and Germany, before moving to pasadena, California.
He joined the Caltech faculty in A Von Karman assistant reported on Eugen Sanger's rocket-motor experiments in and stoked the nascent interest of several people, including Von Karman and a Cal tech graduate student, Frank Malina. Malina had always been interested in rocketry, and proposed to write his doctoral dissertation on problems of rocket propulsion and the flight characteristics of sounding altitude rockets, which are used solely for measurements within the atmosphere, including temperature, pressure, density, composition, structure, and movements of the atmosphere. 2 ! Under Malina's direction, the GALCIT group, tested its first rocket in October The first successful test came in January it brought new financial support and people into the GALCIT fold.
Hsue-shen Tsien, a Chinese-born engineer and brilliant applied mathematician, was one of the new people. Tsien returned to China in the and founded that country's intercontinental ballistic missile program. 22 The GALCIT built its first stationary test apparatus to test rocket engines in The test apparatus was mounted to a building; however, a test exploded and destroyed the apparatus. 23 Not surprisingly, the noisy and dangerous tests were viewed with suspicion and distrust by the Cal tech administration, which prompted discussions about moving the tests out of the facility. In the project found a safe site 7 miles away from the Cal tech campus in the Arroyo Seco at the foot of the San Gabriel 21 Koppes, 3; and Jacob Neufeld.
The Development of Ballistic Missiles in the United States Air Force, Washington, Office of Air Force History, 22 Koppes,S, 31. 23 Koppes, 7. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 12) Mountains, away from a heavily populated area. The GALCIT group secured a lease with the City of Pasadena and began building small frame and corrugated metal structures during the summer of 24 A JPL planning study stated: Construction of research facilities in the Arroyo Seco began in Buildings were temporary, based on Caltech's expectation that research would be sustained only as long as hostilities continued in Europe.
Neighboring residents tolerated the installation's unharmonious military appearance and noises on the assumption that they were temporary 'war effort' inconveniences. The structures were also considered unpleasant by their inhabitants. The first building, 15 feet square, corrugated metal-clad, and crammed with rocket plumbing, was dubbed the "gas house" by its users. 25 The troubled political climate in Europe was reflected in a bolstering of U.S. Army Air Corps support of aeronautical research, including rocketry. As such, GALCIT came directly under the aegis of the Army Air Corps in July although it was initially sponsored by the National Academy of Sciences. The GALCIT/JPL was awarded several federal contracts during WWII for urgent military-oriented research projects.
These early rocket tests were conducted during a period of intense research-and- design work and mark the beginning of state-sponsored scientific research which benefitted the military.26 The practical demonstration of constant-pressure, long- duration, solid-propellant engines was among GALCIT's early breakthroughs. This technological advancement was the basis of GALCIT/JPL's JATO rockets--liquid-propellant or solid-propellant rocket engines and motors 27 for assisting aircraft takeoff. 2' 24 Koppes, 11. 25 Daniel, Mann, Johnson, and Mendenhall. 26 McDougall, Walter. . .. The Heavens and the Earth: A political History of the Space Age.
New York, New York: Basic Books, 27 In rocket industry parlance, liquid-fueled propulsion devices are called engines; the term motor is reserved for solid fuel propulsion devices . 28 Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 13) The development of JATO technology was the first major Army Corps contract that GALCIT/JPL earned. The successful development of JATO became the laboratory's first major technological breakthrough. Jacob Neufeld states that: Through his association with Maj. Gen. Henry H. Arnold, von Karman won the backing of the Army Air Corps for the project at Caltech. The Air Corps was especially interested at that time in developing rockets for use as aids in the takeoff of heavily laden aircraft.
Because the term "rocket" connoted something futuristic and impractical, however, it was decided to call them jet-assisted takeoff (JATO) devices instead. In January the Air Corps provided for this jet propulsion research project, nicknamed Project GALCIT, after von Karman's laboratory. Based upon the promising findings of the study, von Karman won a in July to design and construct small solid- and liquid-fueled rocket engines." The JATO was a solid-propellant or liquid-propellant motor or engine mounted on an aircraft to assist takeoff. Various ingredients fueled the JATOs including black powder, asphalt mixed with potassium perchlorate as an oxidizer, and a red fuming nitric acid (RFNA)/aniline mixture.
3D The GALCIT group tested liquid-propellant JATOs between August and April at Muroc Army Air Base (AAB), and at March Field in Riverside, California. The U.S. Navy used JATO extensively during the last two years of WWII for carrier-based operations in the Pacific. Aerojet Engineering Corporation, a JPL spin-off company, was created to further develop and market JATO motors during the latter years of WWII. 31 The JATO was also the propulsion system for Dr. John Paul Stapp's rocket sled between and The rocket sled was located east of the JPL Edwards Test Station at the Muroc Flight Test Base, which later became a part of Edwards AFB. Dr.
Stapp was a pivotal figure in the development of improved safety restraints for aircraft pilots and in the consequent determination of human endurance limits in extreme decelerations. His work was instrumental in the eventual adoption of seat belts 29 Neufeld, 39. 30 31 Koppes, Daniel, Mann, Johnson, and Mendenhall; Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No, CA-163 (Page 14) by the American automobile industry." While the GALCIT was actively developing JATO, the Germans developed the pulse-jet V-I and the V-2 ballistic rocket which attracted the attention of the Americans and the British during WWII.
During the summer of GALCIT scientists studied and commented upon British intelligence reports concerning the V-I and the In November GALCIT scientists concluded that the rockets held great military promise and urged their development by Army Air Force (AAF) Materiel Command. Materiel Command hesitated; however, Army Ordnance expressed a strong interest in rocket development. In January after the acquiescence of Materiel Command, the Ordnance Department contracted with Caltech's rocket team, GALCIT, to undertake the ORDCIT (Ordnance Department, California Institute of Technology) Project to design and develop a series of liquid-fueled rockets and associated launching hardware. This was the beginning of the Private and Corporal (and Sergeant) rocket programs that JPL developed for the Army.
Frank Malina directed the development of the Private and Corporal rockets . By the end of GALCIT consisted of about 85 people manning an office building, two laboratories, and several test pits." The GALCIT began formally calling itself the JPL in 3 ' David Baker relates: that while most of the work embraced by these assignments was centered on rocket propulsion, the word 'jet' was applied in each and every case when an organization was set up to conduct theoretical and practical tests. The popular interpretation of the word 'rocket' had too flippant a connotation to engender the degree of respectability demanded by the work!" GALCIT's new name, brought an additional $3 million in 32 Stapp, John Paul.
Interview by Richard Wessel, Linda Stowe, Lewis Riede, Ted Liveratos, and Frank Kou on 10 December at Edwards AFB, California. Transcript on file, AFFTC/EM, Edwards AFB, California; Hudlow, 33 Daniel, Mann, Johnson, and Mendenhall. Koppes, 20 . 3' 35 Baker, 72. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 15) funding, and the tripling of the staff to more than 250 people. 36 By the mid population growth in the surrounding communities of Pasadena, Altadena, La Canada, and Flintridge began to limit the facility's ability to conduct large-scale rocket engine tests. 3 ? At World War II's conclusion, the area was heavily settled with upper middle-class residences, some of which overlooked the Arroyo Seco. The area's residents " ...
objected to the noise of static tests, and to the laboratory's unsightliness ... 38 For example, the Corporal E liquid engine produced 120 decibels of noise at an altitude of 200 feet. 39 The JPL scientists and engineers were forced to look for an isolated location where it would be possible to conduct noisy and hazardous tests. The JPL had tested JATO rockets at Muroc earlier and was familiar with the Base. Consequently, when JPL searched for a nearby, yet isolated, site for its rocket engine testing facility in the Muroc Flight Test Base was perceived as a perfect solution. The new JPL facility was known as the ORDCIT test station, until it was renamed the JPL Edwards Test Station in Testing Missiles for the Army Four major Army projects engaged JPL during WWII.
In addition to the JATO project, JPL undertook an Army hydrobomb research program for the Materiel Command Aircraft Lab. The JPL also undertook ramjet research and had the ORDCIT contract for research and development of guided missiles. 40 The first projects conducted under the ORDCIT mandate explored different approaches to missile design. The guided missile project led directly to the development 36 Daniel, Mann, Johnson, and Mendenhall. 3? Gibbons, John and William C. Tibbitts. Edwards Facili ty Historic Overview". Typescript on file at AFFTC/EM, Edwards AFB, California, 38 Koppes, 48. 39 Bluth, John. (Archivist, Jet Propulsion Laboratory, Pasadena, California). Telephone conversations with Scott M. Hudlow, January . 40 Koppes, 21; Neufeld, 42.
JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 16) of the ORDCIT test station at the Muroc Flight Test Base, which was established in On 2 January the Air Technical Service Command, headquartered at Wright Field in Ohio, gave JPL permission to build a test facility at the Muroc Flight Test Base; construction began 16 days later. The test station was staffed and equipped by the ORDCIT Project and considered an extension of the Arroyo Seco facility in Pasadena, California." The ORDCIT test station was originally conceived as a hydrogen-oxygen liquid propellant test station. The the successful WWII German rocket used a hydrogen-oxygen liquid propellant mixture as fuel and oxidizer. This prodded the American scientists to emulate the German rocket.
Frank Malina, however, stated: We did not switch to liquid oxygen after we knew the V-2 was using it and I pointed out in my ORDCIT memoir that I think the u.S. people made a big mistake in switching to liquid oxygen and falling head over heels for the German group. Now no military rocket uses liquid oxygen; i t uses in fact storable propellants, the storable propellants that were developed at military sense. I think the V-2 caused a diversion in the I do point out that it was important later on for space testing. 42 Discoveries by JPL during WWII led to a successful RFNA/aniline, oxidizer/fuel combination that was the basis of the laboratory's early liquid propellant research.
Liquid propellants and oxidizers were the focus of the early rocket testing at Muroc, including hydrazine (N2 H,) and mono methyl hydrazine or CH3 HN' NH2 ) , which are extremely flammable and toxic, and commonly used as liquid propellants. Aniline (C 6H sNH 2 ) was an early fuel. Liquid propellant rocket engines possess several important characteristics which make them attractive propellant systems to reach deep space. Liquid propellants are extremely excitable and hypergolic, which means that a small amount will go a long way and fuel and oxidizer will ignite spontaneously upon contact. Liquid propellants offer 41 Shoop, Richard L.
Historical Report of Technical Engineering, Army Air Field Base Unit, Muroc, California, for the Month of May Report on file at AFFTC/HO, Edwards AFB, California. 42 Malina, Frank J. Interview by James H. Wilson, 8 June JPL Archives, Oral History Program. Transcript of interview on file at the JPL Archives, Pasadena, California: 13. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 17) long-term storage capabilities, and unlike a solid propellant, which burns constantly after ignition, liquid-propellant rocket engines can be shut down when propulsion is no longer needed. The JPL planned a missile series that mirrored the military ranks.
To the amusement of the Army Ordnance Department, the JPL planned to have the missile ranks stop at Colonel, because Von Karman believed that was "the highest rank that works. The ORDCIT test station's first major liquid propulsion project was the Corporal missile. The Corporal missile was the Army's second missile project. It was preceded by the Private A and Private F missile program, which did not lead to a production model. 44 Private A was an eight-foot tall, 10-inch diameter, 530-pound, unguided, solid propellant rocket. It had a mile range, and was first success in rocket-powered flight.
The Private A missile was powered by an off-the-shelf Aerojet asphalt-based, composite solid-propellant JATO motor boosted by an Army Artillery solid fuel motor of pounds thrust and a specific impulse of 186 seconds. When the Private A emerged in late it was seen as the first experimental platform for a series of sequential tests leading to development of the long range missile. Work on the latter aerodynamic design, the Corporal missile, awaited preliminary results from the Private A. 45 original research on solid propellants led to effective applications of solid propellants in several prominent and military missiles. Private A's success during the latter years of WWII brought pressure to improve the missile for use as a strategic battlefield weapon.
Private A's developmental process engendered the Private F missile. The Private F used the same solid-propellant motor as Private A. It was essentially a Private A with wings designed to add stability and increase range. The flight tests, performed at the Hueco Range, Fort Bliss, Texas, were dismal failures. Each Private F missile that was tested achieved a corkscrew flightpath trailing white smoke after a short flight. The JPL realized " ... that a missile with lifting surfaces needed guidance 43 Koppes, 22. 44 Activities at White Sands and Edwards Commence in LAB-ORATORY, May 5. 45 Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 18) equipment for satisfactory performance. With this lesson in mind, the JPL began moving towards the more complex Corporal rocket.
Before JPL developed the successful Corporal E missile, several generations of Corporal missiles were designed, including the "Without Altitude Control," (WAC) Corporal. WAC also stood for "Women's Army Corps" since the WAC Corporal was considered the little sister of the Corporal E." The WAC Corporal was a sounding rocket that was also a test version of several liquid- propelled rockets, including the Corporal E missile. David Baker states that: Malina had high hopes that the rocket would play an increasingly successful role in the field of pure science, but recognized the difficulty in getting military funds for a project which had little application to the needs of the armed forces.
Yet, there was much that a sounding rocket could provide that would be essential information for the following generation of ballistic and guided missiles and the drive to pursue a more benevolent, scientific, research activity could well find equivalence in the requirements of the services. 48 The WAC Corporal had been inspired by a U.S. Army Signal Corps requirement, processed through the Ordnance Department, for an atmospheric sounding rocket capable of reaching a height of feet carrying a small 25-pound payload. Work began in The Douglas Aircraft Company collaborated with JPL to produce the rocket. The WAC Corporal had a solid-propellant booster and utilized an aniline and nitric acid, liquid fuel/oxidizer combination.
The WAC Corporal could reach a maximum speed of miles per hour during ascent, and carried three clipped triangular fins at the booster stage. It later formed part of the Upper Air Research Program. In October a WAC Corporal flew to a height of feet with a 25-pound payload. The WAC Corporal went on to form the design basis for the Aerobee sounding 4. Koppes, ? 47 Koppes, 23. 48 Baker, 74. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 19) rocket. 49 The WAC Corporal rocket engine was probably the first rocket engine tested at the Muroc test station. Its prototype engine was fired on 19 September 50 The WAC Corporal was a pencil thin l6-foot tall missile; it was fueled by a modified liquid- propellant JATO engine using RFNA and aniline.
The JPL reported that "the WAC Corporal, began production in following conferences with Ordnance Department. Firing tests on the WAC Corporal were held during the month of October, at White Sands proving Ground.,,51 Compared to the earlier Private F flight tests, the October WAC Corporal tests were amazingly successful. The WAC Corporal engine shut off at about feet, yet the radar tracked the missile to a height of about feet, more than 40 miles. It flew for 7.5 minutes. The JPL personnel were thinking beyond the somewhat limited capabilities afforded by the WAC Corporal ballistic sounding rocket in They were looking to the stars.
The pressing need for war munitions was over, and it seemed an opportune moment to consider rocketry's future beyond the context of the needs of the armed services. Towards the end of JPL conducted a brief study on the possibility of launching an artificial earth satellite and concluded that, using the same propellants as those designated for the WAC Corporal it would require a rocket with 3.1 million pounds of thrust to place a 10- pound payload into a path that would reach escape velocity. The rocket would consist of 5 stages, each operating sequentially to achieve the speed of miles per hour.
The JPL team theorized that even if more efficient propellant combinations could be found and the mass of the rocket decreased accordingly, and even with the most ideal chemistries, the assembly would still be prohibitively large for the technology then in existence." Four years later, A WAC Corporal missile was the first 49 Baker, 50 "Edwards Tests Station Marks Birthday." LAB-ORATORY, April 3 . .51 LAB-ORATORY, May 5 . 52 Baker, 76. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 20) manmade object to leave the Earth's atmosphere. On 11 October at White Sands, New Mexico, a WAC Corporal was attached to a captured German V-2 rocket and launched into the stratosphere.
The WAC Corporal/V-2 combination was called the Bumper-WAC; it was also the first successful staged rocket to leave the Earth's atmosphere. 53 The Bumper-WAC program was implemented between and as part of General Electric'S (GE) Hermes project. GE needed to study the technical problems of separating rocket stages in flight, determine the possible instability of high altitude flights in the rarefied atmosphere, and evaluate techniques for high altitude ignition. The Army married the V-2 and the WAC Corporal, with the latter mounted on the nose of the so that WAC Corporal could reach greater altitudes than the single stage The WAC Corporal was used without the solid propellant booster normally fitted to the sounding rocket, since it was unnecessary. The V-2 would act as the booster rocket.
At liftoff, the Bumper-WAC combination stood nearly 62 feet tall and weighed tons. In the Bumper-WAC configuration, the WAC Corporal had a length of 16 feet and a diameter of one foot. The 46-foot-long V-2 provided a first stage boost of 25 tons at liftoff and about tons at altitude. In a typical flight, the v-2 would carry the WAC Corporal on its nose for 60 seconds of main engine burn. The V-2 would shut down and separate from the WAC Corporal which would then fire its liquid-propellant engine for 45 seconds with a thrust of 150 pounds. The last two Bumper-WACs were launched from Cape Canaveral in These were the first flights from what is now known as the Kennedy Space Center, Florida. 54 The Bumper-WAC again anticipated future directions, when JPL would truly begin to look to the stars.
Corporal Rockets and Test Stand "A" A spartan industrial landscape burgeoned in the high desert to support the vital missile testing. The JPL test station at the Muroc Flight Test Base was developed to static-test the propulsion systems on Corporal missiles. The original complex was 40 acres. Many JPL personnel lived at the station, staying full-time for weeks on end, others traveled from Pasadena to Koppes, McDougall, 99 . 53 ,54 Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page 21) Muroc to conduct tests as needed. John Gibbons and William C.
Tibbitts wrote: The first major project at the Edwards Test Station (ETS) was the development and qualification testing of the Corporal Missile in the late This was a liquid-propellant system, tested on "A" Stand, that produced pounds of thrust. At that time, this represented the largest rocket engine test stand in the free world.
55 Initially, development centered around the Corporal Test Stand (known as Test Stand "A" after and the associated facilities necessary to support the test stand, which was built in early A plaque in front of the JPL administrative building commemorates the first firing that was supposedly conducted on 2 April However, the JPL site log states that the first firing was conducted on 19 June at 56 The 2 April date actually honors when the first JPL employees arrived at the test station as it neared completion. The test stand is a small steel frame anchored to a heavy reinforced concrete foundation. The stand has a vertical atmospheric firing position with a large excavated flame pit to the east into which flames and exhaust were expelled.
Rocket engines were strapped into the stand for static testing. The JPL test station at Muroc recieved its formal name, the JPL Edwards Test Station in The name change reflected the test station's change in status from a temporary to a permanent station. Nomenclature changes at Edwards AFB affected the JPL name change. During WWII, two distinct facilities had been located on the Muroc Army reservation. Muroc AAB was a training facility for Liberator bomber and Lightning fighter crews; the Muroc Flight Test Base was a top secret flight test base for early Army jets, particularly the Bell XP-59A Airacomet. The Muroc Flight Test Base had an identity distinct from Muroc AAB. The JPL test station at Muroc was located at the Muroc Flight Test Base.
The two facilities, the WWII training base and the WWII flight test base, were integrated into one Base in when the United States Air Force was created. In Muroc APB became Edwards AFB. 57 55 Gibbons and Tibbitts, 1. 56 Bluth Interview, January 57 Hudlow, 16. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 22) The Corporal E, a surface-to-surface, liquid-propellant missile, was successfully developed for the Army. The program began in it was the U.S. Army's first generation, short range ballistic missile. The Corporal E was an American response to the German V-2 and adopted several technical approaches reminiscent of the Graphite vanes in the exhaust nozzle effected radio guidance and control. The first Corporal E was a " ...
full-size, surface-to-surface liquid propellant missile. The heavy 39-foot long Corporal weighed pounds empty and pounds when fueled and was designed to carry a to 500-pound payload miles. It used a RFNA/ethyl aniline, oxidizer/fuel combination to produce a thrust of nearly 9.1 tons. Four elongated fins were attached to the base of the single stage rocket. This missile was subsequently disparaged, because it was an expensive system, although it met all of the Army'S requirements. The Corporal E only had a range of 50 miles. 59 The Corporal E engine test facilities were completed in June at Muroc Flight Test Base. They were operated under the direction of Walter B. Powell, the first engineer-in-charge at Muroc test station.
The rocket engines were fired vertically downwards for 1.5 minutes on Test Stand "A." The first engine, Type 1, a regenerative-cooled rocket engine, was ready for testing by 12 September The TYpe 2 rocket engine was ready 3 months later. The TYpe 3 film-cooled rocket engine was riot used for the Corporal rocket, and a Type 4 rocket engine with longitudinal cooling, expansion joints, and pounds of thrust was discussed. Test data was recorded by cameras photographing the instrument panel in Building 4203/E-4, the Test Stand "A" Control Center, now known as the Test Stand F Monitor, located 60 feet south of the test stand.
The first Type 1 regenerative-cooled rocket engine was tested at Muroc on 10 December Although the equipment had been thoroughly checked by feeding water through the propellant circuits, the Type 1 regenerative-cooled rocket engine'S throat burned out after 15 seconds. However, the Corporal E engine run was not stopped until 48 seconds had elapsed. This was the first 58 Koppes, 39. 59 Caidin, Martin. Countdown for Tomorrow: The Inside Story of Earth Satelli tes, Rockets and Missiles and the Race Between American and Soviet Science. New York, New York: E. P. Dutton and Co., Inc., Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 23) test firing of a Corporal E engine at Muroc test station.
60 Other engine designs were discussed, including copying the German Wasserfall engine or a Type 5 engine with expansion joints and helical cooling passages. TYPes 3 and 4 rocket engine development was stopped, and a second TYPe 1 rocket engine was test run about 9 January A water-cooled TYPe 2 engine was tested on 18 January it ran for 64 seconds and produced pounds of thrust. By January the Corporal E missile, with conditioned engine requirements, had a range of about 60 miles.
A planned January Corporal E missile test firing date was changed to 15 July By May this test date was postponed to 11 October Scaled down (lI5) test models, "Baby Corporal Es," were test-fired at the Muroc test station on 6 May and 7 May The Baby Corporal Es were fired vertically on a rail launcher, demonstrating the possibility of zero-speed vertical launch with no jet vanes. 61 By mid-July engine and tank fabrication difficulties had delayed the Corporal E test firing until 1 December The JPL successfully launched the first Corporal E on 22 May at White Sands Proving Ground, New Mexico; its propulsion subsystem had been tested and qualified at the Muroc test station.
62 The Army pitted GE and JPL against each other in the simultaneous development of the Hermes missile versus the Corporal missile system. In Army Ordnance decided to make Corporal a weapon; however, from the end of WWII until the summer of when it became a weapons program, the Corporal was considered an advanced systems development vehicle. Corporal's development and testing provided the overall integration to understand system problems. Meanwhile, GE's Hermes A had a 75- mile range and flew; the Hermes B, which was theorized to have a 150-mile range, never flew. Army Ordnance worried that a tactical missile would not be ready for field deployment by the mid if it depended on GE. JPL officials assured Army Ordnance that the Corporal E would be ready.
In the mid it became the Army's first battlefield ballistic missile. 60 LAB-ORATORY, May "This rail launcher still survives and appears in HAER photo CA-163-6. 62 It is slated for preservation by the Edwards Koppes, 39. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 24) Sergeant Missile The next planned guided missile in missile ranks was the Sergeant missile, a solid-propellant rocket, which was tested at Pasadena in the late and into the Solid propellant testing continued at Pasadena until when i t was moved to the JPL Edwards Test Station.
Solid propellants are a combination of fuel and oxidizer, which is brought together and mixed into a single solid mass called the "grain." The fuel is usually prepared in a liquid state; the oxidizer was prepared in a solid state, usually as a powder, and mixed with the fuel. When the grain is prepared, it solidifies to form the propellant. An alternative solid propellant is a double-base type solid propellant. In this combination, each of the two primary constituents could, theoretically, burn on its own accord in a vacuum. The double- base type solid propellant contained a mixture which has the properties of fuel and oxidizer. The two constituents together provide better burn characteristics than either demonstrated alone.
The Sergeant rocket motor overcame theoretical problems that halted earlier attempts to use solid propellants. Solid propellants had power and sustainability problems that were difficult to overcome. The Sergeant emerged as a single-stage, solid propellant rocket with a length of 34 feet and a 30-inch diameter. The forward section was an elongated cone with straight sides that converged to a point; four stabilizing aerodynamic fins were clustered around the base. The XM-IOO solid-propellant rocket motor produced a thrust of tons; launch weight was around tons. 63 The Sergeant was the first ballistic missile to benefit from advancements in solid- propellant technology.
In a JPL engineer demonstrated that a rubberlike polysulfide developed by the Thiokol Corporation possessed many of the best characteristics of the asphalt solid propellant the JPL was using in its JATO. However, the rubberlike polysulfide developed a burning-rate problem and formed a cone inside the propellant charge. The problem was solved by utilizing the star-shaped solid propellant charge developed by English researchers and scientists at the Allegheny Ballistics Laboratory in West Virginia. Clayton Koppes related that; 63 Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 25) JPL researchers learned of the star almost by accident, through an appendix to another report being circulated among military laboratories.
For the Thunderbird motor [a small, 6-inch diameter rocket designed to test the polysulfide solid propellant] the engineers applied a thin liner to the wall of the combustion chamber, then mounted a ten-point-star-mold core in the center of the chamber. They poured the polysulfide propellant in the chamber and, when the propellant began to harden, removed the star. The design was simplicity itself. When the Thunderbird motor was ignited, the charge burned slowly from the inside, and the star gradually formed a cylinder. The burning-rate problem was solved, and the polysulfide proved it could withstand the acceleration. 64 The development of an efficient solid propellant is and America's distinct contribution to rocketry.
It opened the doors for the development of large solid-propellant rockets such as Minuteman, Polaris, and Poseidon, which were developed at various laboratories in the and Although JPL was successful in developing the Corporal and Sergeant missiles, the organization was not comfortable conducting classified military research. The need for secrecy struck many JPL personnel as distinctly at odds with the goals of higher education as exemplified at Caltech and with the desire to conduct scientific research. 65 The JPL ceased military applications after the Sergeant missile's successful development and militarization in The 20-year association with Army Ordnance was over.
Deep Space: The Next Frontier The JPL spent the transforming the Corporal E and Sergeant missiles into effective weapons systems for the Army. However, they were beginning to shift from guided missile research to instrumented deep space exploration. While JPL was working for the Army on the Corporal and Sergeant missiles, a German group was also working for the Army. The Army brought several hundred German engineers and scientists, including Dr. Wernher von Braun, to the United States during Operation Paperclip after WWII, before the Russians were able to 64 Koppes, 37. 65 Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 26) spirit the scientists away to Russia. The Army also captured a supply of German V-2 rockets.
The Army organized a team of these German scientists at Fort Bliss, Texas to conduct studies concerning development of long-range, surface-to-surface guided missiles, including an effort to refine the German In May the German scientists began helping the Army test launch the captured V-2 rockets at the White Sands Proving Grounds, New Mexico, which is adjacent to Fort Bliss. Several years later, the German scientists were transferred to the Redstone Arsenal in Huntsville, Alabama, and began developing the Redstone missile. Dr. von Braun and his German colleagues formed the basis of the Army Ballistic Missile Agency (ABMA).
The Navy and Air Force (then the AAF) also began their own missile programs in the late It briefly appeared that a single national guided missile program would be established to eliminate duplication of effort among the services. The Army and Navy both favored such a development; however, the AAF strongly opposed the plan. Officials from the AAF feared that a single program would jeopardize their chances of gaining sole responsibility for development and deployment of long range guided missiles. An interservice rivalry over control of guided missiles ensued as each service sought to define its role and mission. The ambiguous nature of guided missiles helped fuel the controversy over control of missile development and deployment.
Army officials claimed that ground-launched missiles were merely extensions of artillery and therefore the Army'S responsibility. However, Air Force officials claimed that missiles were robot, or pilotless, aircraft and therefore fell under the jurisdiction of the Air Force. The first foray by JPL into space exploration began modestly in The JPL embarked on the development of Orbiter, an artificial earth satellite, in collaboration with the ABMA and the Office of Naval Research (ONR). The Orbiter project was planned to help celebrate the forthcoming International Geophysical Year (IGY). This proposal was competing for the right to build the first American satellite.
The Orbiter satellite proposal was composed of a Redstone solid-propellant rocket as a first stage, and downsized Sergeant motors for the second and third stages necessary to place the satellite in orbit around the Earth. This project marked the beginning of a phased program for instrumented deep space exploration involving JPL and the Army. 66 66 Daniel, Mann, Johnson, and Mendenhall; Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 27) The ABMA/ONR/JPL entry into the satellite competition was impressive. Two other proposals were prepared in addition to the Orbiter proposal.
The Orbiter proposal's competition came from the Vanguard proposal, and an Air Force proposal, which entailed the use of an Atlas rocket coupled with an Aerobee-HI second stage to achieve earth orbit. However, President Dwight D. Eisenhower wanted the project to have a non-military focus and desired to have America's first satellite utilized in peaceful and scientific studies.~ Faced with the three plans, the Department of Defense organized a special advisory group to review the various proposed satellite programs and make recommendations. Although the special advisory group favored the use of an Atlas missile, the NRL gave Vanguard superior electronic technology to transmit scientific data from space back to Earth.
The committee was also concerned about adapting military missiles instead of developing a nonmilitary rocket. The advisory group eventually decided that the Navy program had the best chance of placing the most useful satellite into orbit within the IGY. These factors steered the advisory group to favor Vanguard, which it chose. This decision led to a controversy, over which was the best proposal, Orbiter or Vanguard. The Soviet Union's successful launching of Sputnik on 4 October made the Orbiter-Vanguard controversy a moot point. Instead, Sputnik bred a controversy over whether choosing Vanguard was a good decision. 68 The JPL did, however, find an outlet for its Orbiter project. The ABMA in the mid was engaged in an interservice rivalry with the Air Force.
This rivalry involved developing the Jupiter medium-range ballistic missile before the Air Force finished its Thor medium-range ballistic missile. The Orbiter studies helped the ABMA create the reentry test vehicle , which became the Jupiter missile's ablation-type nose cone. The JPL also contributed its Microlock electronic technology to the Jupiter missile studies. The Microlock electronic technology is a phase-locked loop tracking system, which later became the foundation of the Deep Space Network that tracks deep space vehicles. The first RTV was fired by the Army on 20 September and attained an altitude of 682 miles and a range of miles, new records for American missiles. The ABMA was not allowed to launch a satellite, so the fourth stage was filled with sandbags.
However, if the ABMA/JPL RTV had 67 McDougall, 68 Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 28) contained the fourth and last stage, it would have become the first orbiting satellite. 69 The Soviets launched the first satellite to gain orbit, Sputnik, on 4 October The diverse American groups scrambled to respond to the immediate loss of prestige in the eyes of the American public and the perception that the U.S. was falling behind the Soviet Union.?O Three weeks after Sputnik, Orbiter was given a renewed opportunity, but not before the Vanguard team had its Orbiter's name was changed to Explorer 1, and it continued as a backup to Vanguard. One month later, on 3 November the Soviets placed Sputnik 2 in orbit, which included Laika, the space dog.
Project Vanguard was plagued with technical problems. The Vanguard launch vehicle, which had not been perfected prior to this undertaking, frequently exploded. Vanguard was launched on 6 December It never left the pad. Instead it sat and burned uncontrollably on national television. Meanwhile on 8 November JPL had been authorized to proceed with Explorer launch preparations. The Explorer satellite was launched on 29 January boosted by a Redstone medium-range rocket developed by the ABMA. Explorer 1 was a success and America's first artificial satellite. While Explorer 2 did not achieve orbit because of a structural failure, Explorer 3 was the second American satellite in orbit on 26 March Explorer 3 also discovered the Van Allen belts which circle the Earth.
The JPL was now firmly established as the nation's leading space program, as well as a leading missile development agency. In December various military space programs and contractors were consolidated into the National Aeronautics and Space Administration (NASA) including the JPL sites at Pasadena and Edwards. 71 The JPL was reluctant to join the new NASA space agency. The JPL felt it had the opportunity to become the lead contractor for the new space agency, a role which NASA did not necessarily endorse. The NASA was created from the National 69 Koppes, 80. 70 McDougall, 71 Study. Butowsky, Harry A. Man-in-Space National Historic Landmark Washington, National Park Service, Department of Interior, JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 29) Advisory Committee on Aeronautics (NACA); President Eisenhower gave NASA the right to absorb any space-related agency it wanted, such as the which had developed the failed Vanguard rocket and satellite, and the ABMA, which became Marshall Space Flight Center in Huntsville, Alabama. By NASA's primary goal was to land a manned spacecraft on the Moon. NASA was specifically pushing project Mercury, the first manned space program. However, JPL decision makers decided to develop unmanned rather than manned spacecraft. The JPL would have the primary role in the unmanned program, rather than join the other numerous NASA installations involved in the manned spacecraft program.
7 ' The JPL Edwards Test Station would play an important role in unmanned deep space exploration program, according to Gibbons and Tibbitts: .Under a NASA contract, JPL received its first assignments to lead the nation'S unmanned exploration of the solar system. The Edwards Facility has supported JPL in this work from the start and has made significant and vital contributions to leadership in lunar and interplanetary exploration. 73 Thus, including the JPL Edwards Test Station, quietly laid the groundwork for a successful manned space program through its technological breakthroughs and successful scientific missions in the unmanned space program.
During this period, JPL established deep space tracking stations at six overseas sites controlled by a a5-foot antenna at Goldstone [Fort Irwin), near Barstow, California which was listed on the as a NHL in These installations and the ground communication system linking them constitute NASA's The JPL laid out a course of unmanned deep space exploration and proposed it to the new NASA officials in early The JPL planned to commence with a circumlunar probe and expand outward to planetary exploration. The primary determinant for which planet to visit first was its proximity to Earth; JPL created a 5-year plan to visit or Venus and Mars.
The proposal was modified by NASA and who developed a revised space program in The new space exploration program coupled NASA's desire for lunar flight with predilection for planetary 72 Koppes, Newell, Gibbons and Tibbitts, 1. '3 74 Daniel, Mann, Johnson, and Mendenhall. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 30) investigation. The lunar hard landers were called Rangers, and the Venutian, Martian and Mercury orbiters and probes were called Mariners. From to every spacecraft launched by JPL had its propulsion subsystems qualified at the JPL Edwards Test Station.
This included the Pioneer series of interplanetary probes, the Ranger lunar series in the early the Surveyor lunar landers in the mid the Mariner series of interplanetary landers and probes in the and early the Viking Mars orbiters and landers in the mid and the Voyager series which conducted of Jupiter in the late Voyager 1 departed the solar system in after conducting a of Saturn. Voyager 2 is heading into interstellar space also. It conducted of Saturn, Neptune, and Uranus into the 75 The liquid propellant propulsion testing for these spacecraft was conducted at Test Stand D, which was built in The Ranger Spacecraft The Ranger series was the first class of deep space vehicles JPL developed.
The Ranger vehicle series was developed in blocks of three to five spaceflights that had related missions. The early Ranger vehicles were designed to test spaceflight technology, and to discern whether the Ranger design was satisfactory for reaching the moon. The second block of Ranger missions was designed for science experiments; on these missions Rangers incorporated television cameras, a seismometer, and a gamma-ray spectrometer. The third block of Ranger missions was designed to support manned spaceflight objectives directly. The Ranger series began inauspiciously on 22 August after four aborted launches. The launch of Ranger 1 was successful; however, the second stage of the Agena rocket, which was designed to place it in the moon's orbit, failed.
Ranger 1 tumbled into Earth's atmosphere and disintegrated. Nevertheless, JPL engineers believed they had enough data and readied Ranger 2 in an optimistic mood. Ranger 2 suffered the same fate as Ranger I--the Agena second stage burn did not work correctly. The spacecraft was destined for a fiery death. Ranger 3 overcame the propulsion problems with the Agena rocket; however, it became rapidly apparent that a computer code had been inverted. Ranger 3 was flying a mirror image of its intended flight path. Ranger 3's antenna was not pointing toward Earth; the central computer 75 Gibbons and T ibbi t ts, 1. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 31) and sequencer failed. Ranger 3 tumbled out of orbit and sped into solar orbit.
Suffering from a bout of optimism--although privately officials doubted if the mission would be successful-- JPL launched Ranger 4 in It landed on the moon on 26 April unfortunately, the spacecraft was dead on arrival. Nothing worked once Ranger 4 reached the moon, because the master clock and sequencer had failed. A NASA official was quoted as stating, "All we've got is an idiot wi th a radio signal." 76 While Ranger 4 was a failure in most respects, it was, indeed, the first American spacecraft to land on the moon. Following Ranger 4, five months elapsed while JPL reevaluated the program. Ranger 5 was launched on 18 October Barely an hour into the flight, electric power from the solar panels short-circuited and the craft's temperature soared.
Ranger 5 was switched to battery power, even though the batteries would be exhausted long before the spacecraft reached the moon. A mid-course correction was attempted to ensure that Ranger 5 hit the moon; however, the spacecraft missed it by 450 miles. .. The Ranger program was in shambles. The NASA and JPL responded by completely overhauling the program. Controversial sterilization practices were canceled, excess scientific experiments were ditched, and Ranger 6 was postponed for a full year. Ranger 6 launched on 30 January It had a perfect flight to the moon, except that in mid-flight the television telemetry system activated for 67 seconds then shut itself off. Ranger 6 landed perfectly on a hard lunar surface, but the television system never reactivated.
The NASA reacted bitterly to another Ranger failure, and proceeded to target the Ranger project for cancellation. The management was desperate to find a suitable solution. A Ranger success was the only item that could redeem On 28 July Ranger 7 sailed towards the moon. It landed three days later on the lunar surface. The cameras came on line and displayed the lunar landscape for the first time. Finally, a Ranger had worked. Now that JPL had a success to build upon, the remainder of the Ranger spacecraft worked wonderfully. Ranger led from hard landers to the Surveyor series of controlled soft landings on the moon which transpired in the mid in direct support of NASA's manned Apollo program.
Surveyor 1 made the first soft landing on the moon on 2 June and demonstrated that the lunar surface could support a spacecraft. Surveyor 6 lifted off from the moon and moved to a 76 Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 32) new location, demonstrating the first engine restart on an extraterrestrial body.77 The Mariner Spacecraft The early Mariner interplanetary probes were developed and launched while JPL was undergoing the Ranger crises. While the early Ranger series was experiencing excruciating problems, the Mariner spacecraft soared fairly smoothly and even exceeded expectations in some instances. Mariner's goals were " ...
to pass near the planet, to communicate with the spacecraft near the planet, and to perform a meaningful Planetary experiment." 78 Mariner 1 experienced the worst problems of any Mariner or Ranger spacecrafts; it was destroyed within 5 minutes of launch on 22 July The launch vehicle and spacecraft veered on a wildly erratic course and was destroyed by the range safety officer: a hyphen had been omitted in the launch-vehicle guidance system equations. 79 Mariner 2 was launched a month later on 26 August and seemed destined for a fate similar to Ranger 1 and Ranger 2. However, the guidance problem was solved before the Agena second stage separation. Mariner 2 soared for Venus and passed i t on 14 December providing scientists with unparalleled scientific data about the planet.
Furthermore, Mariner 2 succeeded in proving that spacecraft could reach neighboring planets with accuracy. Mariner 2 set a communication record by sending a signal 54 million miles, and lastly, Mariner 2 functioned perfectly for several months, dispelling several about space travel. 80 After a 2-year hiatus, Mariner 3 and Mariner 4 flew in This time reaching Mars was the goal; Venutian exploration was shelved until more sophisticated spacecraft were built. Mariner 3 was launched for Mars on 5 November after designers found innovative means to overcome new problems attendant upon shooting for a more distant target. The spacecraft quickly ran into 77 Valerie Neal, Cathleen S. Lewis, and Frank H. Winter. Spaceflight: A Smithsonian Guide. New York, New York, W. W.
Norton, 78 Koppes, 79 Koppes, 128 . 80 Koppes, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 33) problems. A protective fairing, a nose shield, would not eject, creating two major problems: the spacecraft weighed too much to reach its target, and its solar panels would not unfurl. Mariner 3 was declared dead after nine hours. A team of Lockheed, and Lewis Research Center personnel found that the fiberglass fairing was not vented; it exploded violently in a heat-vacuum test, revealing Mariner 3's most likely fate. Lockheed, the fairing's manufacturer, quickly cast a vented magnesium fairing. This saved the Mariner 4 shot, which had a month-long launch window after the Mariner 3 fiasco. The launch window would be closed for two years, if Mariner 4 could not be saved.
Mariner 4 was launched successfully on 28 November It reached Mars on 14 July and relayed the first television photos of the Martian surface. Mariner 4 dispelled several about the Martian landscape and delivered new information about Mars to scien tists .81 The important and successful Mariner series of interplanetary continued into the mid Mariner 5, a modification of Mariner 4, was launched towards Venus on 14 June 82 Mariner 5 provided data on atmospheric readings, temperature, and magnetic fields. Venus was found to have no significant magnetic field which is probably due to Venus's slow solar rotation, only 243 Earth days, and extremely high surface temperatures. 83 Mariner 5 used radio signals to probe the venutian atmosphere.
Mariner 6 and Mariner 7 were Mars missions launched on 25 February and 27 March respective1y.84 Mariner 6, which arrived at Mars on 30 July "took measurements of the structure and composition of the atmosphere, images of the surface, and measurements of surface temperature. Mariner 6 also carried a infrared spectometer, to sense the spectral distribution of Martian heat energy. 86 Mariner 7 was an 81 Koppes, 82 Bruce Murray. Journey into Space: The First Thirty Years of Space Exploration. W. W. Norton, New York, New York, ,83 Neal et ai, 84 Murray, 56. 85 Neal et ai, 86 Murray, 55. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 34) identical mission to Mariner 6, scheduled to study the polar regions of Mars.
However, the radio signal died; a rechargeable battery on Mariner 7 had exploded and destroyed critical portions of the spacecraft. Mariner 7 was reprogrammed to bypass the damaged portions of the spacecraft, and resumed its polar mission. Mariner 8 and Mariner 9 were designed as a joint mission to fly complimentary polar and equatorial orbits around Mars. However, Mariner 8 suffered a launch failure, when it was attempted on 8 May and landed in the Atlantic Ocean. Mariner 9 survived the launch on 30 May 87 and spent a year conducting the work of two spacecraft mapping Mars using radar and thermal imaging, after encountering an initial dust storm.
It demonstrated that Mars had distinct northern and southern hemispheres, volcanic features, dry river channels, lava flows and polar regions comprised of carbon dioxide (C0 2 ), which suggests that Mars once had a warmer, wetter climate. 88 Mariner 9 was the last mission to Mars before the Viking missions in the mid . Mariner 10 was a mission to orbit Venus and Mercury. Mercury was thought to be a planet that could reveal important information about the Moon. Mercury was thought to have a heavily cratered surface that could have maria (dark plains), "giant scars recording collisions from an extinct family of Earth-circling satellites that once accompanied the moon.
Mercury was also interesting as a place to test geologic theories since it was thought that one side of Mercury was perpetually in sunlight and extremely hot, while the other side was in the eternal cold and darkness of the planet's nightside. Before Mariner 10 Mercury's dark side was thought to be the coldest place in the solar system." Mariner 10 was launched on November 3, and underwent several crises, including an electronic glitch that caused its computer to reset. The spacecraft's primary power system fluctuated periodically, its nitrogen attitude-control gas hemorrhaged, and the movable scan platform starting sticking before Mariner 10 arrived at Venus on '87 Murray, 88 Neal et aI, 89 .0 Murray, 93. Murray, 95. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 35) 5 February 91 Mariner 10 arrived at Mercury in March and found that Mercury resembled the Moon and could be compared to it, vindicating the mission's premise. Mercury was also found to emit excess natural radio noise from the supposedly frigid nighttime side of the planet, which demonstrated that Mercury's nighttime side is not the coldest place in the solar system.
Mariner 10 discovered the planet's magnetic fields and studied the planet's surface and atmosphere during its three Mariner 10 was also the first probe to visit two planets and to use a gravity-assist technique for interplanetary travel." Viking and Voyager By the mid and into the early JPL had finally begun solving many of the earlier technical problems and was consistently developing successful interplanetary spacecraft. Mariner brought plans for a Martian lander. The Viking series of orbiters and landers brought these plans to fruition in the mid Viking 1 and Viking 2 were launched in August and September to ascertain signs of life on Mars. The Viking landers carried a gas chromatograph/mass spectrometer which was designed to separate and identify organic compounds.
The Viking's could detect a few parts per billion of nearly any carbon-based organic compound in a soil sample. The Martian soil was collected by the Viking lander and subjected to gas- exchange tests and labeled-release tests in which the Martian soil was combined with nutrients that terrestrial organisms commonly consume and a serving of basic, fundamental organic compounds, such as amino acids, respectively. Water vapor and liquid water were combined with the soil in both sets of tests. A third test analyzed the role of CO 2 in the Martian atmosphere and the impact of solar energy on the metabolic processes on any potential Martian organisms. The tests were too strong for the Martian soil to reveal sign of microorganic life. Chemical reactions were created, rather than biochemical.
Not a single organic molecule was found, it is a completely sterile environment. 93 viking 1 touched down on Mars on 20 July 7 years after Man first walked on the moon. Its cameras revealed a barren, rocky, and rust-colored surface. Mars was found to be 91 Murray, 113 92 Neal et ai, 93 Murray, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 36) rust- or red-colored due to the amount of oxidized iron in the soil and due to the arid nature of the desert-like planet. Water is possibly restricted to a permafrost layer below the surface and the polar ice cap. Viking 2 touched down on the side of Mars opposite to Viking 1 and combined with Viking 1 to map nearly 100 percent of the planet's surface over the next three years.
viking 1 expired in and Viking 2 terminated in The Viking landers hopped from location to location using their rockets to maneuver. The Vikings studied the gravitational field and atmospheric water vapor. A thermal map of Mars was also created. The landers transmitted more than images and conducted biological soil and atmospheric tests. The Viking Orbiters lasted until and transmitted over color and stereo images of Mars." The late brought the initial planning for Voyager, which was conceived as proceeding on a "Grand Tour" of the solar system. 95 The Grand Tour was canceled in due to budgetary concerns, since it was planned as an expensive project through the entire solar system.
JPL responded by formulating a cheaper project called Mariner/Jupiter/Saturn , which was approved and transformed into Voyager. The Voyagers were scheduled to encounter Jupiter and Saturn, and possibly Uranus. Voyager had an enhanced computer which drove the attitude control system. 96 The identical Voyager 1 and Voyager 2 were launched in Voyager 2 was launched on 20 August sixteen days before Voyager 1, which was launched on 8 September Voyager 1 is was the first Voyager probe to encounter Jupiter, hence the name. Voyager 1 was on an easier, faster trajectory to Jupiter, while Voyager 2 was a longer trajectory which could be retargeted to reach Uranus.
Voyager 1 would encounter Jupiter in March four months before Voyager 2, and then Saturn, 20 months later in November The Voyager 2 launch was smooth, however, the spacecraft experienced several bouts of robotic "vertigo." The disoriented spacecraft alarmed the JPL controllers, who subsequently discerned a slight mis-setting of computer parameters. 97 The spaceflight was uneventful once the 9' Neal et aI, 95 Koppes, 96 97 Murray, Murray, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 37) initial problems were corrected. Voyager 1 discovered a thin ring around Jupiter, studied the planet's magnetic field and the Great Red Spot, a permanent storm which moves in a counter-clockwise rotation. Voyager 1 used Jupiter's gravity to fly a trajectory on to Saturn.
Studies of Saturn's rings revealed that the rings are composed of "thousands of ringlets made up of countless ice and dust particles. Several Saturnian moons were discovered, bringing the total to 20. Voyager 1 also studied Titan, a Saturnian moon, which was found to have a thick, smoglike atmosphere, before heading out into the solar system. After Voyager 2 encountered Saturn in August it continued on to Uranus and Neptune. In January Voyager 2 made its closest of Uranus. Voyager 2 studied Uranus's ring system, photographed its surface and moons. Voyager 2 revealed 10 additional undiscovered Uranian moons, bringing the total to 15.
Voyager 2 proceeded on to Neptune, which it encountered in late It studied Neptune's ring system and its largest moon Triton, and discovered 6 new Neptunian moons. 99 The Voyagers continue to transmit data in the as they speed towards the edges of the solar system. The JPL reached an apogee in the early with the Voyager projects. Its focus changed as JPL tackled new and different projects, in the face of the success and the budget of the Space Shuttle, and the enormous distance to the unexplored outer planets.
The work at the JPL Edwards Test Station slowed considerably as NASA reevaluated its programs in the wake of declining budgets, and the perceived success of the Space Shuttle program, which was developed by the North American Aviation division of Rockwell International, an aerospace company. The Space Shuttles were reusable, an important characteristic deep space landers and probes lacked. Closure of JPL Edwards Facility Today, deep space continues to bring new challenges for JPL to overcome, due to the great distance from earth of the unexplored outer planets in our solar system. The Cassini and Mars Pathfinder projects, which were first conceived in the mid and Pluto projects bring new opportunities for 98 Neal et al, 99 Neal et al, JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 38) as it once again attempts to make discoveries that stretch the boundaries of knowledge and experience However, the JPL is currently closing its Edwards Facility and will return the administration of the property to the Air Force Flight Test Center (AFFTC) at Edwards AFB, effective 1 October The closure plan includes demolishing 13 buildings, mothballing 37 buildings, cleaning 18 buildings, leaving 9 buildings as is, removing all equipment from 2 buildings, and performing 1 Resource Conservation and Recovery Act (RCRA) closure. The disposition of two buildings has yet to be determined. JPL records located at the Edwards facility will be transferred to JPL archives in Pasadena, California.
JPL Test Stands and the Industrial Cultural Landscape The JPL Edwards Facility in is a complex composed of 83 structures, including 80 industrial structures (7 of them test stands), one commercial structure, one administrative structure, and one security facility. The complex dates from and grew throughout the entire Cold War period. The rocket engine test stands dominate JPL Edwards Facility's industrial cultural landscape and are its focal point. The JPL Edwards Facility ceased building activity in By that time, the facility had developed an extensive complex dedicated to the testing of liquid and solid propulsion systems for guided missiles, deep space probes, interplanetary landers, and commercial satellites.
Building campaigns revolved around the diverse spacecraft propulsion systems and their peculiar project requirements. Historical events had a profound influence in shaping the JPL Edwards Facility's cultural landscape. A cultural landscape is the communal sum of the built environment, including technology, vernacular architecture, and the social and experiential webs that bind a community, including work communities. Technology, vernacular architecture, and the cultural landscape are reflectors of conscious and unconscious ideas and concepts; they are historical products that reveal intent and define social and cultural relations. A cultural landscape also reflects choices of and adaptations to the natural landscape and its ecological systems.
Technology is viewed as "an expression of our culture, encoded with our dreams, purposes, 100 Murray, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 39) environment, insights, and limitations. In a article, Dell Upton stated "artifacts of every scale are physical expressions of the continuous articulation of space that we all carry in our heads." 102 Integration of different types of artifacts can be achieved by studying the built environment as a holistic entity--a cultural landscape. The term "cultural landscape" arose from cultural geography. It allows an investigator to integrate individual components of a community into a general context of related building types, time periods, and places.
The cultural landscape reflects the manner in which a place is the product of its own unique history; a cultural landscape is a growing and evolving entity. The JPL Edwards Facility cultural landscape is spare and organized around requirements focused on either liquid or solid propellant engine and motor testing in a desert setting. The JPL Edwards Facility's built environment reflects these unique requirements and attests to the rigors of testing advanced technology. The exacting standards and unique construction underscore the inherent ecological and human safety concerns and the uncommon requirements of testing advanced technology. The JPL faced increased local pressures in Pasadena, California as WWII drew to a close.
It was realized that the laboratory was not simply a wartime operation; JPL was becoming an integral component of a new post-World War II political, military, and social order. Although JPL had an important future role in missile development and deep space exploration, upper middle-class residents of nearby La Canada and Pasadena thought that the laboratory was unsightly, noisy, and kept strange hours. They intimated that the laboratory was incompatible with their quiet upper middle-class neighborhoods. It was also beholden upon JPL to move its test facility to a sparsely populated area to prevent damage to neighbors in the event of an accident. Rocket engine testing utilizes highly 101 Pursell, Caroll W.
"The History of Technology and the Study of Material Culture" in Material Culture: A Research Guide. Thomas J. Schlereth, ed. Lawrence, Kansas: University Press of Kansas, 102 Upton, Dell. "The Preconditions for a Performance Theory of Architecture," Comment on "Time and Performance: Folk Houses in Delaware," by Bernard Herman in American Material Culture and Folklife: A Prologue and Dialogue, Simon Bronner, ed. Ann Arbor, Michigan: UMI Press, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 40) combustible and excitable materials and compounds that are dangerous to handle and use. Subsequently, Army Ordnance found JPL an isolated, secret site to test Corporal rocket engines: the Muroc Flight Test Base.
Site Characteristics The climate at Edwards AFB is a mid-latitude desert type with hot, dry summers and cool, slightly moist winters. Average precipitation is less than centimeters (5 inches) per year, with most occurring as rainfall during the winter months. Temperatures range between 38 and 43 degrees Celsius and 110 degrees Fahrenheit) in summer and drop to well below freezing in the winter. The climatological regimen dictates a reliance on subsurface water for contemporary permanent human habitation. Prevailing winds are from the west south west and southwest; calm presides only 15 percent of the time (see the wind rose on Sheet 1 of the HAER drawings) . The Base occupies portions of the alluvial floors of several intermontane valleys in the western Mojave Desert.
The JPL Edwards Facility is located between 1.5 and meters (5 and 35 feet) below the fossil shoreline of Pleistocene Thompson Lake,03 at an average altitude of 701 meters feet) above sea level. Edwards AFB is located within the geologic structure known as the Mojave Block, and is bounded by the Garlock and San Andreas Fault zones. The faulting and uplift associated with the Mojave Block has created a region which is geologically complex, with both Tertiary and pre-Tertiary geologic formations as well as later Quaternary alluvial sediments. The JPL Edwards Facility is located in an area of recent Quaternary alluvium composed of alluvial sand and gravel, playa clay, and wave-deposited sandbars. '04 The JPL Edwards Facility is located within the xerophytic phase saltbush scrub community.
The dominant shrubs represented in the project area include allscale (Atriplex polycarpa) , cheesebush (Hymenoclea salsola) , golden cholla (Opuntia echinocarpa) , creosote bush (Larrea divaricata var. tridentata) , 103 Dibblee, Thomas W. "Geology of the Rogers Lake and Kramer Quadrangles, California." USGS Bulletin U.S. Department of the Interior, Geological Survey (USDI -USGS), Washington, D. C.: U. S. Government Printing Office, . 104 Dibblee, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 41) boxthorn (Lycium cooperi) , rice grass (Oryzopsis hymenoides) , spinescale (Atriplex spinifera) , and wolfberry (Lycium andersonii).lOS Elm trees (Ulmus at the JPL facility were planted to provide shade and relieve some of the visual starkness of the natural landscape.
While JPL was located at Muroc AAB, the Muroc Flight Test Base was not part of the Base until The Muroc Flight Test Base was a separate, autonomous base, under the auspices of Materiel Command (later Air Technical Service Command), dedicated to testing experimental aircraft, particularly the Bell XP-59A Airacomet, the first American jet aircraft Construction began in January on the Muroc test station. The JPL quickly built the Corporal Test Stand (Test Stand nAn) and additional buildings to support the vital testing at Muroc. The Muroc test station was remotely operated; JPL personnel from Pasadena managed the station and drove to it to perform engine testing. The missiles were test launched at White Sands, New Mexico, Fort Bliss, Texas, and Cape Canaveral, Florida. 10 ?
,The planned, institutional landscape of the JPL Edwards Test Station evolved episodically between and Planning decisions were reactionary and geared toward meeting challenges and solving problems. The dynamism underscores the importance ascribed to technological advances during the Cold War, and demonstrates how rapidly technology and corresponding social and cultural changes occur. The cultural landscape reflects the changing needs of the burgeoning post-World War II missile industry and a modern deep space research and development facility. The commonplace architecture of most structures at JPL belied the importance and the radical nature of the guided missile and space probe testing conducted at the JPL Edwards Test Station during the second half of the 20th-century.
Building sites were chosen as needs were identified. The JPL did not have an initial master plan; construction decisions were made on an individual, building-by-building basis as various missile and space probe programs were implemented by the military 105 Vasek, Frank C. and Michael G. Barbour. nMoj ave Desert Scrub Vegetation, n in Terrestrial Vegetation of California. Michael G. Barbour and Jack Major, eds. New York, New York: John Wiley and Son, 106 Hudlow, 16. 10? Koppes, 39; Baker, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 42) services, NASA, and Congress. The Army Corps of Engineers (ACE) built, planned, and laid out the ORDCIT test station in however, they did not assist in locating the test site.
The AAF and JPL chose the test station's location at the Muroc Flight Test Base for its proximity to Pasadena, lack of human habitation, clear weather, and the fact that the land was already under military ownership and security. The JPL Edwards Test Station was designed for maximum economic and spatial efficiency (consistent with safety and climatic factors). Robert Kreger notes that "Utilitarianism plays a role in shaping planned landscapes. It is characterized by the absence of waste. It is an uncomplicated, no frills, landscape management philosophy. . .. It affects architectural design and styling standards, and serves to prohibit the construction of unnecessary and cost-prohibitive facilities which might be deemed luxurious.
"lOB Indeed, the JPL Edwards Test Station was small, compact, and had a minimum of buildings when it was originally established. The ACE initially utilized temporary architecture, construction techniques, and materials. The test station only grew when the mission expanded or changed its focus and new construction (or alteration) was necessary to meet changing mission goals. Some of the new missions introduced new planning factors to the evolution of the JPL site. The majority of later construction was designed by Austin, Field, and Fry of Pasadena, California, various contractors, and the JPL Plant Engineering office.
The test station's architecture and cultural landscape continued to reflect those initial needs and goals; it eventually became a complicated, planned industrial landscape coexisting with a desert ecology. The ACE designed the early test station complex with ease and speed of construction in mind. The ACE drew on its vast experience with simple prefabricated temporary wooden buildings, and the cultural landscape at the JPL Edwards Test Station consciously and unconsciously reflects these architectural and economic values.
The architecture of the JPL Edwards Test Station constitutes a form of vernacular or folk architecture based upon Kreger, Robert David "The Making of an Institutional lOB Landscape: Case Studies of Air Force Bases, World War I to the Present." diss., University of Illinois, Champaign, Illinois, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 43) the repetition of building forms and types. 109 The military vernacular nature of the JPL Edwards Test Station makes it a powerful place evocative of spartan living and serious purposes. The architectural design criteria embodied by the temporary buildings at the JPL Muroc test station were as follows: Ease and speed of construction ... Framing remained simple.
Anticipated manpower shortages made it necessary to use unskilled labor. Only a portion of those employed on building crews would be experienced carpenters, so framing techniques were intentionally designed to be uncomplicated. Platform framing, in which floors are framed separately (as opposed to balloon framing), had been in practice since the turn of the century. Second-story floors obtained greater stability and load-bearing capacity. Dimensioned lumber and stock items such as doors and windows were used throughout. The concrete foundation piers of most company buildings were 8 x 8 in. posts of 5 ft. height, set on 16 in. square .concrete footings installed 3 ft. below grade. Anchor bolts set in the middle of each pier fastened a composite sill made up of three 2 x 8s spiked together.
The sills carried 2 x 8 joists that spanned 10 or 13 depending on the building Prefabrication was not new, having become an important part of the building industry in the late 19th-century.111 The U.S. military began using prefabricated building units in the early 20th-century. Temporary building types constructed during World War I included barracks, warehouses, messhalls, etc. To the extent that prefabrication was normally" ... used in the construction of U.S. military bases, it was in the use of 109 Vlach, John. "The Concept of Community and Folklife Study" in American Material Culture and Folklife: A Prologue and Dialogue. Simon J. Bronner, ed. Ann Arbor, Michigan: UMI Research Press, 110 Garner, John S.
World War II Temporary Military Buildings: A Brief History of the Archi tecture and Planning of Cantonments and Training Stations in the United States. USACERL Technical Report, Champaign, Illinois, 111 Bishir, Catherine, Carl Lounsbury, Charlotte Brown, and Ernest Wood III. Archi tects and Builders in North Carolina: A History of the Practice of Building. Chapel Hill, North Carolina: University of North Carolina Press, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 44) prepared materials such as ready-cut lumber delivered to site, and in the assembly-line manner in which buildings were erected. Despite its availability, prefabrication was not a common civilian building technique until after WWII.
Temporary buildings were numerous and important intrinsic elements of the cultural landscape of WWII military installations, including the JPL Muroc test station, which was sponsored by Army Ordnance and unconsciously modelled after a military installation, particularly in the utilization of temporary architecture. Initial Construction: Test Stand "A" The Muroc test station was initially arranged on a central north/south axis (approximately 344 0 azimuth).
The original entrance to the JPL test station is located directly south of Building 4200/E-1,113 Originally, the JPL test station was a dense cluster of support buildings centered on the Corporal Test Stand, (or Test Stand "A," as it was known after The original 40-acre site was planted with elm trees, which provided shade in the hot desert sun; Fig. 1 shows the location of trees in the original Corporal Test Stand area (as well as the "Short Snorter," Test Stand ca. The roads were asphalt-paved and the building lots were scraped of native vegetation. A security fence was erected around the test station to thwart unwanted visitors.
Building 4202/E-3 is on the east side of the original north/south axis and is located at the northern edge of the test station complex away from the majority of the complex (its UTM coordinates are The Corporal Test Stand was constructed to test liquid-propellant rocket engines for the Army's Corporal guided missile program. In the late Test Stand "A" was the largest test stand in the Western world. It is possibly the country's and the world's oldest permanent rocket engine test stand. This test stand was the cornerstone of the JPL Muroc test station in Test Stand "A" consists of a small, steel I-beam framework 112 Garner, 14. 113 The dual numbering system for JPL structures reflects the heritage of JPL and NASA facilities management systems.
The "E" (for Edwards) numbers were originally assigned by The series was assigned by NASA in when the JPL Edwards facilities were transferred from ORO/Army Corps of Engineers to NASA under executive Order No. ,, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 45) Fig. 1 Trees shown heavily outlined in this site plan were planted ca. (see Illustration Sources for citation); 50-foot grid. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-:l63 (Page 46) and the associated tanks and plumbing necessary to test missile engines. The test stand rests on a poured-in-place concrete foundation anchored deeply in the ground with its east facade facing a flame trench excavated to the east. The poured concrete was laid in wooden shuttering (see HAER photo CA-163-A-l).
The bottom of the flame trench immediately to the east of the stand is lined with concrete and has a drain (see HAER photos CA-163-A- The flame trench has partially filled with earth as its sides have slowly subsided from lack of maintenance. Test Stand "A" has a single atmospheric vertical firing position: engine exhaust was vented downward directly into the atmosphere. At the bottom of the central channel in the foundation was a "flame bucket" or deflector designed to direct the exhaust into the flame trench. The flame bucket was originally lined with refractory brick, laid in stretcher bond, later shielded with steel plate (see HAER photo CA-163-A-5).
Atop the foundation, a rectangular steel frame supported a light travelling hoist for the transport of engines and equipment between engine mounts and delivery trucks. A pyramidal steel tower was added to the top of this structure within a year of initial construction to provide a single lifting point for a block and tackle over the flame channel centerline. (In later years a 3-ton hoist running on an I-beam rail was erected around the south, east, and west facades of the travelling crane tower.) Steel stairs to the upper levels of the test stand are on the north facade, and were constructed at the same time as the tower. Catwalks on the east side of the test stand access the flame trench and the flame bucket.
Stainless steel tanks for distilled water, fuel, and gaseous nitrogen (GN 2 ) are in situ in reinforced concrete bays on the north facade of the test stand (see HAER photo CA-163-A-16). All oxidizer tanks such as an oxidizer storage tank ("A"), oxidizer scrubber tank, and smaller tanks designated "B" through "E" were decontaminated and removed before this writing (see Fig. 2 for schematic of "A" Stand propellant systems). Interconnecting piping, valves, tubing and monitoring devices were all removed in decontamination procedures several years ago. 1l4 For tests, a rocket engine was secured in the middle of the test stand with the nozzle pointed down into the flame bucket, directing the flames and exhaust into the flame trench.
Maximum 114 Decontamination involves draining all remaining propellants from tanks and plumbing, flushing the systems clean with distilled water, and then removing all items (primarily tanks and plumbing) normally associated with a specific test program. After tanks and plumbing are removed from a test stand, all that is left is a bare structural steel framework. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 47) , Fig. 2 Test Stand "A" Fuel and Oxidizer Schematic JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 48) test firing capability was possibly pounds of thrust.
'15 Liquid fuels and oxidizers, such as white fuming nitric acid (WFNA), RFNA, and aniline were piped to the engine from stainless steel tanks using GN 2 to "pump" the fluids and remotely operate the necessary valves. The tanks were perhaps located on the north facade to keep sunlight from unduly affecting the temperature and pressures of propellants and/or to shield the control center or "blockhouse," Building 4203/E-4, from any accidents involving the tanks. Over the years, additions and modifications were made to the original "A" Stand structure. A reinforced concrete machinery room was built onto the south side in to provide space for refrigeration equipment.
When the interstand tunnel system was built in access to "A" stand was created on the west side of the "A" Stand foundation (see HAER photos CA-163-1; CA-163-A- 7). The test stand was later used as a non-firing, propellant flow stand for testing component hardware, such as valves, pumps, and tanks during the and Test Stand "A" has been abandoned for 10 to 15 years; it became evident that it was too small to test large modern rocket engines and could not be economically modified to house high- altitude simulation apparatus.
Test Stand "A" Ancillary Structures Seven temporary buildings were built in to complete the initial test station complex (see HAER photo CA-163-1) 4200/E-l: an administration building/photo lab 4201/E-2: Test Stand "A" Work Shop 4203/E-4: Test Stand "F" Monitor (historically the Test Stand "A" Control Center) UTM 4204/E-5: Storage Building 4205/E-6: Guardhouse 4206/E-7: Observation Post 4212/E-13: Paint Storage Shed These temporary buildings were constructed on poured-in-place concrete slabs, with wooden frame walls covered by stuccoed gypsum board. They were designed to remain serviceable for a period of 15 to 30 years, and all wooden structures were placed 115 Koebig and Koebig.
Master Plan for Edwards Test Station Report on file at JPL Edwards Facility, Edwards AFB, California, unpaginated. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page 49) to the west or south of the test stand to avoid engine exhaust plumes and any wind-borne propellant fumes. Only two original buildings, in addition to Test Stand "A," survive from the initial construction period: Buildings 4200/E-1 and 4203/E-4. The remaining five structures were demolished after Buildings 4201/E-2, Test Stand "A" Work Shop; 4205/E-6, Guardhouse; 4206/E-7, Observation Post; and 4212/E-13, Paint Storage Shed. The Test Stand "A" workshop, Building 4201/E-2, was a small, one-story, one-room structure with a gable roof of composition roofing materials.
The interior workspace was x and contained a 9' -6" long workbench in the northern end. Outside, an emergency shower was attached to the east facade facing the test stand, near an off-center door. A door and small window were on the south facade. An addition was added to the west facade."6 The Storage Building was demolished in It was a 0" x two-room shed of the same construction as the workshop. The rafter butts of its overhanging roof were cut in a decorative pattern. The shed had two doors on the northern facade: the eastern one was for equipment and the western for personnel. A slatted casement window pierced the west facade. Building 4212/E-13, Paint storage Shed was a 48-square foot, one- story shed located on the western edge of the complex.
Building 4205/E-6, Guardhouse, was approximately x and located south of Building 4200/E-1, adjacent to the perimeter fence. This one-story shed had a single centered entrance on the east facade on the opposite side from the traffic flow into the test station. 117 The Observation Post, Building 4206/E-7, was a three-sided, poured-in-p1ace concrete structure open to the south.
It was long, wide, and high and located 200 feet southeast of Test Stand "A." Its 8-inch thick walls had three 1- thick bulletproof plate glass windows centered on the north facade facing the test stand; each window was about 16" x Personnel and visitors watched the Corporal engine tests from this observation post, prior to when the Control and 116 Control and Energy Conversion Division, Facility utilization ETS, Edwards Test Station, Edwards, California. Unpublished Manuscript on file at JPL/Edwards Facility, unpaginated. 117 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 50) Recording Center (4221/E-22) was constructed.
The Test Stand "F" Monitor, Building 4203/E-4 (historically the Test Stand "A" Control Center or "blockhouse"), is a one-story, one-room, flat-roofed, poured-in-place reinforced concrete structure situated 60 feet south of Test Stand "A" at UTM Only x in size, it had walls and ceiling one foot thick to shelter test personnel and their control and recording equipment (no original equipment remains inside). Test personnel observed events through five 16" x 21" windows made of thick bulletproof plate glass set in the north facade, facing the test stand. Bulletproof plate glass windows also pierce the east and west facades, each sheltered by a small, vestigial concrete hood. Entrance was gained on the south side via a three-foot wide gas-proof steel door.
The view towards Test Stand "A" is now obscured by the Test Stand "A" Barricade (Building 4216/E-17), an earth-filled wooden structure erected in to protect the control center from shrapnel in the event of an explosion at the test stand (UTM coordinates Several additions have been made to the old control center, including a one-story, plywood shed telephone junction booth that has been attached to the west facade and a one-story wrap-around shed on the south and west facades. The building has not been used as a control facility since when Building 4221/E-22, the Control and Recording Center, was built; today it is simply a storage facility.
Building 4200/E-1 was the original administration building/photo laboratory (see HAER photo CA-163-1), and utilized the same construction as the other temporary buildings. It was x a size and form identical to the lavatories erected at the Muroc Flight Test Base during WWII. 118 As an example of pre-fabricated, temporary WWII construction, these small building forms could be adapted for diverse uses. The east half of the building contained administrative offices, and the west half housed a work and storage room and a photographic darkroom. Building has been extensively modified over the last 50 years to serve different functions.
It was the test station's main administrative office until In the mid it was utilized as an office and photo laboratory; it was the standards and chemistry laboratory in currently it is the safety equipment repair shop.'19 118 Hudlow, 49. 119 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 51) Building activity quieted until except for the construction of one new building. Building 4207/E-8, Shop and Living Quarters, was erected in to support the ongoing Corporal rocket engine testing. Building 4207/E-8 was a one- story, frame and stucco, gable-roofed shop building that was later transformed into an instrumentation repair and storage building. Building 4207/E-8 rested on a poured-in-place concrete foundation and probably had 12-light casement windows.
Originally, the building had a machine shop and a welding shop on the northern end. The southern end of the building contained a living area arranged on a center passage. Toilets, a darkroom, an office, and a coffee room completed the structure. The building was 116 feet in length and 20 feet wide. A x one-story shed wing was attached to the north end of the east facade; it contained the welding shop and the toilets. Building 4207/E-8 was demolished in as an extreme fire hazard; portions of the roof and ceiling had collapsed. Test Stand "B" In the early focus began to change. The JPL disliked conducting classified military research, and resented becoming an Army "job shop. Space exploration always interested but its work primarily came from Army guided missile contracts.
In JPL was given the opportunity to work on a space-related project. Project Orbiter was a satellite project which used downsized 6-inch diameter, solid-propellant Sergeant motors as a booster. Orbiter was later renamed Explorer 1. In January it became the first American satellite to reach orbi t. In to help facilitate this shift in research from guided missiles to deep space exploration, JPL built a new test stand at the Edwards Test Station to support exotic and hazardous fuels testing. This signalled an important new phase of research: the study of exotic 12 ! fuels and oxidizers, particularly hydrazines (like MMH and UDMH) , boranes, and fluorinated compounds.
The JPL newspaper, LAB-ORATORY, reported that: 120 Koppes, 121 "Exotic" was a term that came to signify fuels containing boron compounds; H. Dictionary, 3rd ed. Company, Bennett, Concise Chemical and Technical New York, New York: Chemical Publishing JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 52) installation, now called Edwards Test Station (ETS) has added several buildings, including a second test stand, propellant storage docks, office space, a dark room, sleeping quarters, storage buildings, etc. At the present time there are sixteen structures manned by a permanently assigned crew of twelve, backed by various personnel at JPL who devote part of their time to ETS.
Half of the permanent crew now have their homes near Lancaster, the nearest large residential district, approximately 35 miles from the station, and several more are in the process of relocating in the area. 122 The test station began to be formally called the JPL Edwards Test Station in and was known as such until the mid when the name was changed to JPL Edwards Facility. The initial name change reflected the station's change in status and the name change of Muroc AFB to Edwards AFB; the test station became a permanent operation, focused on testing propulsion subsystems. In the mid the JPL Edwards Test Station had enough work to merit a permanent crew to operate the station.
The sleeping quarters were in Building 4200/E-1, the administration building/ photo lab, and later in Building 4207/E-8, living quarters and shop. The buildings were cramped, however; only two to three people lived at the station, including the photographer. The remainder of the station's personnel lived off-base in the surrounding communities. The focus of the new construction was Building 4215/E-16, Test Stand originally known as the "Short Snorter" (at UTM coordinates the letter designations were not assigned to test stands until Test Stand "C" was built in Like the Corporal Test Stand, the "Short Snorter" consisted of a heavy, reinforced concrete foundation surmounted by a rugged steel frame. Test Stand "B" could support engines that generated upwards of pounds of thrust.
Engines were fastened to the frame on an upward incline; during tests, their exhaust vented directly into the atmosphere towards the east (see HAER photo CA- Liquid propellants and oxidizers such as WFNA, aniline, nitrogen tetroxide, (N,O.), unsymmetrical dimethyl hydrazine (UDMH, or hydrazine (N2 and mono methyl hydrazine, or CH NH2 ) were used. 123 Propellant tanks were located at or very near the test stand, continuing the LAB-ORATORY, April 122 123 KOebig and Koebig. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 53) pattern begun at the Corporal Test Stand. A pivoting one-ton hoist atop the frame lifted engines and equipment into place. A shallow, concrete-lined flame trench was built to the immediate east of the stand, with steps leading down into it.
This flame trench was fitted with various means to protect it from the heat of engine exhaust plumes. HAER photo CA-163-C-2 shows a water spray device made up from standard steel plumbing fixtures lying in the flame trench bottom. Other engine installations at "B" used water spray rings, as can be seen in a aerial photo of Test Stands "C" and "B" (see HAER photo CA-163-D-4); this photo also shows that a steel deflector plate was added at the east end of the pit. HAER photographs CA-163-D-4 and CA-163-5 show that by outdoor storage tanks for fuel and oxidizers had been moved behind earthen barricades (built in to the east of Test Stand This change protected tanks from shrapnel; vented propellants blew to the east, away from personnel in the test stand area.
Propellants were delivered to the test stand via tubing in above-ground racks supported by "unistrut" poles. (The above ground routing provided numerous advantages over a buried installation: ease of monitoring for leaks or damage, and ease of change or repair.) The propellant delivery lines were run on a dogleg well to the north of any engine exhaust plumes so that heat or shrapnel from an accident would be unlikely to damage the lines and cause a propellant spill. (See the upper right of Fig. 1, in which delivery lines are labeled "pipes.") Portable equipment, instrumentation, tubing and piping changed radically at Test Stand "B" depending on the engines to be tested and the nature of the tests to be performed.
A photograph taken in (see HAER photo CA-163-C-3) shows how complex the web of equipment, wiring and tubing was at times involved . .After the construction of Building 4221/E-22, stationary closed circuit television cameras, such as one shown in HAER photo CA-163-D-4 situated south of the test stand, recorded the engine tests. By the late and early engine tests at Test Stand "B" had long since ceased in favor of more modern equipment at Test Stands "C" and however, a special shock tube was installed at Test Stand "B" for a Coast Guard fuel dispensing program in '24 ; the proj ect' s mission was to find less spill-prone ship-to-ship fueling connections for vessels at 124Control and Energy Conversion Division, Facility Utilization ETS, Edwards Test Station, Edwards, California.
Jet Propulsion Laboratory, California Institute of Technology, June entry for No. E-16. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 54) sea (see HAER photo CA-163-C-4). In all that remained of the shock tube installation are two poured concrete tiedown areas, including one forming a cross pattern to the north of the test stand.
Test Stand "B" itself has not been used for a number of years and is in a poor state of preservation in Test Stand "B" Ancil~ary structures In addition to Test Stand five temporary buildings were constructed during the building phase to support the test programs: 4208/E-9: Shop (Instrumentation Building) 4209/E-IO: Oxidizer Dock 4210/E-ll: Fuel Dock 4211/E-12: Test Stand "B" Work Shop 4213/E-14, (later reassigned as Test Stand "C" Shop) The two docks (Buildings 4209/E-10 and 4210/E-l1); Building 4208/E-9, Shop; and Building 4213/E-14, Test Stand "C" Shop still stand.
The Test Stand "B" Work Shop was demolished in the mid All these structures were located to the south, west, or north of Test Stand The need to keep personnel and equipment upwind of engine exhaust plumes and any propellant fumes emerged as a major planning factor in laying out the Test Stand "B" complex and all other JPL test stand complexes. In addition to the factor of prevailing winds, fire and explosion safety zones became planning determinants because of the exotic and excitable fuels intended for use at Test Stand Buildings and structures containing propellants, cryogenics, or high-pressure gases were separated from each other by safety zones, depending on the quantity and volatility of the substances stored.
Distances and limitations on the weights of various propellant classes at JPL Edwards Test Station were displayed in a report by Koebig & Koebig on a sheet titled "Intraline Quantity-Distances. This landscape pattern is standard for storing explosive materials. The greater the number of buildings that housed explosives, the larger the complex. This resulted in a geographically extensive complex at JPL Edwards, due to the need to provide space between buildings so that a potential explosion could be isolated to a single structure. Where intraline quantity-distance limits cannot be achieved by mere separation, barricades surround buildings that are inhabited on a regular basis or are located in immediate 125 Koebig & Koebig. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 55) proximity to buildings that are regularly inhabited. Building 4210/E-11 is located 180 feet southeast of Test Stand and Building 4209/E-10 over 380 feet south of Test Stand the two structures are separated from each other by 190 feet. The fuel and oxidizer docks are raised one-story, poured-in-place concrete sheds with corrugated sheet steel walls and roofs mounted on steel frames. They are open to the south, away from Test Stand "B" itself. A large metal-sheathed container is located in Building 4210/E-11, and a large two- celled, metal-sheathed wooden oxidizer storage box is located at Building 4209/E-10. Building 4209/E-10 also has a porte cochere on the south facade to allow personnel to unload oxidizers in the shade.
Building 4213/E-14, known at present as the Test Stand "C" Shop, was probably built originally to support Test Stand "B" since it was built in four years before Test Stand "C" was constructed. Since it is currently used to support Test Stand further description can be found under Test Stand Building 4211/E-12, Test Stand "B" Work Shop was demolished in to facilitate the construction of Building 4288/E-89, the present systems assembly building. The workshop was a one-story x building of typical temporary materials and design. It had one room with opposing doors on the east and west facades, Building 4208/E-9 was the original instrumentation building; it is now a shop.
Though located across the road, south- southwest of Test Stand "A" (upwind of both test stands), it is part of the Test Stand "B" construction package. Building 4208/E-9 is a one-story x gable-roofed structure of typical temporary construction. Two doors are on the east facade, a pair of two-over-two sash windows are on the north facade, and an eight-light sliding casement window pierces the west facade. A centered, frame and stucco, one-story shed wing was added to the west facade for a telephone juncture box.
A large non-reflective sliding window was added to the south facade, and one to the west facade which overlooks the test area for the short-lived JPL solar power project for which it was the operations center in '26 Building 4208/E-9 is currently vacant and in a poor state of preservation. Workbenches probably lined both sides of the interior wall, when the building was an instrumentation laboratory. The floor is covered with a 126 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-1.63 (Page 56) rubberized material and the walls are covered with celotex tiles.
'l'he Tunnel System The JPL Edwards Test Station began building at a tremendous rate in the late The lure of deep space exploration coupled with the formation of the National Aeronautics and Space Administration (NASA) spurred JPL to begin building new facilities at the Edwards Test Station to handle larger liquid propellant rocket engines. Before the expansion, JPL planned to move the test station to a larger piece of land in order to test liquid engines as large as 1.5 million pounds thrust. JPL officials sought large parcels of land at Camp Cooke (which became Vandenburg AFB) , Camp Pendelton, Fort Irwin, and Edwards AFB, but their plans did not come to fruition.
Instead two additional test stands were built in and Test Stand "e" and Test Stand respectively at the existing JPL Edwards Test Station. (The alphabetical designations were given to the test stands after when a new naming system became necessary due to the growing number of stands.) In addition to the new test stations, an extensive tunnel system was installed to interconnect all test stands with a new computerized central Control and Recording Center, Building 4221/E-22. The 7-foot diameter tunnels were constructed economically of #8 gauge (approximately inch thick) galvanized corrugated steel pipe of the kind used for highway drainage culverts--easily fabricated and quickly laid in trenches cut by bulldozers (see HAER photo CA-163-I-3).
The tunnel system yielded numerous advantages: in addition to giving speedy and unhindered all-weather access between test stands and Building 4221/E-22, the tunnel system also provided shelter to personnel from wind, fire, and fumes. The tunnel system was also designed to carry electrical power, instrumentation and communications cables; water; and non-flammable high-pressure nitrogen and helium (He) lines--all of which would be protected from above- ground damage and could be easily modified or serviced in the tunnel environment (see Fig. 3 and HAER photo CA-163-J-12) . Small portions of the tunnel system were modified at future dates (see HAER photo CA-163-D-II), but the tunnel system itself maintains most of its original integrity.
Concrete was laid in the tube bottoms to create a level surface for people and equipment to move through the tunnels. Work stations, remote firing stations, telephone lines, an intercom system, and emergency lighting are present throughout the system, as are air vents and tunnel access points. Building 4266/E-67 is the tunnel entrance servicing the ,, JPL EDWARDS FACILITY Edwards Test Station> HAER No. CA-163 (Page 57) ,-FlNISH GRADE OIA. CORRUGATED METAL PIPE TUN NEL CATHODICALLY PROTECTED TUNNEL UGHTING - - - , o TELEPHONE rl~----PUBUC ADDRESS SYSTEM CENTRAL RECORDING SYSTEM f-lI't----UNISrnUT CARRIERS POWER DISTRIBUTION rlrt--\t---SPECIAL SYSTEMS HELIUM UNISTRUT CARRIERS r----NITROGEN UNE Otl-fl----WATER DISTRIBUTION 3' 0 WIDE A.C.---~o;c--~ PAVED FLOOR ~~ri+B~~' ..
'0- TYPICAL CROSS SECTION THROUGH UT'ILITY TUNNEL GRAPHIC SCALE FEET Fig. 3 Schematic cross section of typical tunnel at JPL Edwards Solid Assembly Building (4260/E-61) and the Igniter Magazine (4261/E-62), but its size, form, and construction is typical of the tunnel houses, including those not assigned building numbers, such as at test stands "D" and "E." The typical entrance house is a x one-story, concrete block, flat-roofed structure that accesses the tunnel system from the east or west.
Tunnel blower houses, such as Buildings 4219/E-20 and 4225/E-26, are located directly over underground tunnels and contain compressors to provide ventilation, No master plan appears to have been prepared by for constructing Test Stands "C" and "D" or the Control and Recording JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 58) Center. 127 However, engineering drawings for Test Stand "c" and the tunnel system in reveal clearly that JPL engineers were expecting future addi tions The tunnel at Test Stand "C" was designed to overrun the test stand branch to the north and to provide for a westward tunnel connecting the Control and Recording Center, which was built (along with Test Stand shortly after Test Stand "C" was finished.
The two major planning principles driving the test station's layout to this time played a prominent role in the building campaigns. Test Stands and "D" (as well as future stands "E" and all lie along the north-south axis of the easternmost tunnel. All their inhabited support structures and monitoring systems (including the Control and Recording Center) lie to the west of this axis to take advantage of prevailing winds, for removal of engine exhaust plumes, vented fumes, or smoke and dust from accidents. In addition, test stands and potentially dangerous support structures are widely separated, reflecting scrupulous observance of intraline quantity-distance safety measures.
Test Stands "C" and "D" and Their Complexes Test Stand or "Charlie" Stand, as it is known colloquially, was constructed in to conduct atmospheric liquid-propellant engine testing. Its construction was completed mere months before the Russian satellite Sputnik I was successfully launched on 4 October inaugurating the "Space Race" in the international public eye. Test Stand "D" (or "Dog" stand129 ) was begun two years later as testing programs 127 At least, no such plan existed in drawings or reports reviewed for this history. There may be JPL correspondence allUding to considerations for future growth that could be looked upon as an informal master plan.
128 Project field notes contain numerous electrostatic copies of JPL engineering drawings of these stands that were not included in the HAER large format photography record. 129 "D" is usually for "delta" in Air Force parlance, but Bonner indicates "D" Stand was referred to as "Dog Stand" at JPL Edwards; the origin of the term at JPL is obscure. Humorously, one of the authors (Anderson) recalls seeing JPL technical photographs in the course of research in which rocket engine nozzles are capped with protective plastic covers from cans of dog food ("They fit, too!" says Bonner). Occasionally a cover bears the likeness of a collie, "Lassie" of television fame, along with the slogan "Eat the JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 59) expanded.
"D" Stand construction drawings were underway in November just before the formation of NASA and the official transfer of the JPL property from ORDCIT to NASA on 3 December Drawings labeled for a formal request for construction approval were dated 29 January In many ways, what was built at one stand complemented or assisted the other, so the following account interweaves the development of these two sites chronologically rather than treating each stand as a separate entity. Test Stand "C" was the primary research and development test stand at the JPL Edwards Test station. Operational equipment was not tested here.
The poured-in-place concrete base for the original stand survives surrounded by a conglomeration of tanks, scrubbers, and other accoutrements at UTM coordinates Test Stand Building 4217/E-18, as it was constructed in was relatively the same size as test stands "A" or It was built initially to test the liquid propellant propulsion system for the Vega engine, and had somewhat the same engineering as Test Stand "B" (compare HAER photos CA-163-D-2 and CA-163-C-2). Unlike Stand however, Test Stand "C" was integrated with the tunnel system, and took advantage of the tunnel system for centralized power, communications, and gas supplies.
A large bunker in the south side of the stand foundation (accessed by a trap door seen in HAER photo CA-163-D- 2) contained manifolds and small tanks for the distribution of high-pressure GN2 to the valves and systems used in tests. Another bunker or bay was designed into the north side of the stand to house propellant tanks (HAER photo CA-163-D-3). A ramp to the west permitted forklifts and other vehicles to deliver equipment to the top of the foundation. Test Stand "C" saw the advent of a third planning principle for the test stand layouts: segregation of fuel and oxidizer storage tanks and equipment. The fuel storage tanks and fuel management equipment were segregated to the south of the test stand, and oxidizer tanks and equipment were located to the north.
(Location of fuel and oxidizer tanks behind separate barricades at Test Stand "B" took place after "c" Stand was built.) Like Stand Test Stand "c" sported a small, robust steel tower designed to fire engines down into a concrete flame pit cooled with water. Homer Newell writes: " ... the first year [NASA's first year-- produced both progress and wasted motion. It was a period of learning. At the request of the JPL leaders, the Vega upper stage intended for deep-space missions food that Lassie eats!" JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 60) was assigned to the laboratory in the first months, only to be canceled within the year in favor of the Centaur stage.
with its original mission canceled, Test Stand "C" was adapted for propulsion research aimed at finding excitable and safe liquid propellants that could make the trip to deep space with a minimum of volume and weight for propellant storage. In the and early boron compounds were considered for widespread application to space exploration, missiles and military aircraft. A large industry was expected to materialize. Clifford Hampel, writing about boron compounds, states: The hydrides of boron are colorless solids, liquids or gases and are easily oxidized, with consequent large energy liberation. These compounds have been extensively studied by government agencies because of desirable characteristics as rocket fuels.
The highest jet velocities are attained with elements of low atomic weight, and, although hydrogen is probably the "tops" theoretically as a propellent fuel, it is extremely difficult to contain, and so must be combined with other elements, such as boron or lithium. It is generally agreed that, for many reasons, boron is the likeliest candidate for this role. For a propellent fuel of reasonably high bulk density, very high jet velocities may be expected from reacting boron hydride [B 2 H,] with fluorine oxide of water [OF,]; boron hydride is a water-reaction fuel, being highly explosive when exposed to moist air or traces of water.
It is interesting to compare the energy release of boron with other fuels: 1 cu[bic] f[oot] of boron releases Btu [British Thermal Units] upon combustion; the same amount of kerosene, Btu; and gasoline, Btu. Boron-derived fuels to be used in the reaction motors of jets and rockets yield half again as much heat per pound as the best hydrocarbon fuels, and it has been said that such boron fuels will develop into a billion-dollar industry in a decade. These fuels, in a general way, are conveniently made by reacting lithium hydride [LiH] with boron trichloride [Bel,] or boron trifluoride Such reactions, when modified in various ways, can yield diborane (B 2 H6 ) , pentaborane and decaborane (BIOH,.).
Although there still remains much to be learned 130 Newell, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 61) about the various boron compounds, it appears that, as far as the investigations have proceeded, new industries are in the making in which boron, in some form or other, will play an important role. 131 Fluorine has long been known as the most energetic oxidizer of the halogen family (which includes fluorine, chlorine, bromine, iodine and astatine), and fluorinated oxidizers (fluorine compounds including other halogens or oxygen) were expected to release more energy per pound than pure oxygen.
Indeed, JPL photographs show that in the oxidizer chlorine trifluoride (CIF,) was in use at Test Stand and in HAER photo CA-163-D-ll a tank marked for oxygen difluoride (OF,) is in place on the north side of the stand. Chlorine pentafluoride (CIF s ) was used in the 133 Liquid fluorine (LF 2 ) was also employed, as well as a mixture of liquid oxygen (or "LOX") and liquid fluorine known as "FLaX." By insulated in-ground cryogenic tanks were in place for fuel and oxidizer on the stand's south and north sides (see HAER photo CA-163-D-4). Many combinations of fluorinated oxidizers and boron compounds were tried in various engines to determine an optimum combination of engine design, materials, and propellants.
Because of the highly reactive nature of these substances, inert helium gas was used to propel them from tanks through tubing to engines rather than electrically driven pumps. In a helium "tank farm" consisting of 13 horizontal cylinders was installed west of Test Stand and the Helium Compressor Building 4226/E-27 was built in to help maintain pressure at pounds per square inch (psi). Figures 4 and 5 diagram the fuel and oxidizer systems at "C" Stand in the early Due to the turbulent nature of combustion in a rocket engine, some propellants present may not react due to engine wall temperatures, propellant injector patterns in engine combustion chambers, or other factors. Hence the stochiometric quantities 131 Clifford A. Hampel, Rare Metals Handbook. 2nd ed.
London: Reinhold Publishing Corporation, 13' JPL negative number 1 October shows a detail of a clearly labeled drum of chlorine trifluoride. 133Bonner interview, 12 January telephone conversation, 27 June Chemist Cliff Moran, Member of Technical Staff, JPL Pasadena, California indicated in a telephone conversation with Anderson on 27 June that elF, was much more difficult and hazardous to handle than the hydrazines or nitrogen tetroxide. ,, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 62) 0 r- 0\ .-< s:: H ~ s:: s:: 0 H .w - . -i:'-~ ro"" H tJ ,, ;:lro I C!J s:: :2 0 tJ s:: , ,,- w >- ~: -4 I ~ r< V) ~ J~ ~ e "' .....8ro ~ , ~~- ~ I, . l.-Si ~~~ 01 0H ro '" r ! :z~ ~_ . '" '" P< :>, rl '.; .~ . "' 8 P< .. .c ~ .. i ~ ~ .u <ll ;:l .w C!J C!J C!J ;:l .. .
i j; -rl r l <ll ~ ,~ ; 'D s:: 0 ~ ro .w so: :,. (fJ .:. U : JPL EDWARDS FACILITY Edwards Test Station) HAER No, CA-163 (Page 63) , i.' I .t. f 1" j"j '" ", " 1 I!J i. l I I .. I u = JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 64) (balanced to consume all propellants completely in an exact ratio) one might expect in an ideal laboratory setting were not necessarily the most optimal. Years of tests were required to develop data that would aid combustion chamber, injector nozzle, and engine designs and choices of materials.
Ideally, the propellants diborane (B2 H,) and liquid fluorine ) would produce the highest specific impulse--or energy per unit of mass- -but according to JPL test stand engineer John Richard Bonner, "we could never get i t to work right." 134 Problems using cryogenic liquid fluorine (maintained under pressure at F) also had to be overcome. JPL personnel found that bends in the stainless steel tubing used for liquid fluorine had to have long sweeping radii, not sharp bends, or the fluorine would quickly corrode the tubing and cause leaks. Sharp edges and burrs likewise had to be removed from tubing and any passages conducting liquid fluorine. 135 The combustion products of fluorinated oxidizers had their own hazards in earth's atmosphere.
Fluorine combines with the hydrogen in diborane or other hydrogen-containing fuels (like MMH or UDMH) to produce hydrogen fluoride , a highly corrosive gas. Dissolved in water (or the moisture in air), hydrogen fluoride creates hydrofluoric acid, which unlike nitric, sulfuric, or hydrochloric acids, attacks even glass. Tests using these propellants continued from the early through the The diborane tank at Test Stand "C" was replaced in with one having a 256-gallon capacity; the present oxidizer tank (marked "FLUORINE"), also built in has a 186-gallon capaci Both these heavily insulated and jacketed tanks were built by the Cryoquip Corporation of Lynwood, California. Evidently the quantity of propellants expended and byproducts produced was not high.
No obvious lasting effects were noticeable on surrounding vegetation or structures in from the years of atmospheric testing conducted until the fluorine scrubber facility was installed in A site plan from JPL Edwards files dated 21 September shows a 525 gallon FLOX tank at Building E-64 {but no nitrogen 134 John Richard Bonner, interview with Richard Anderson, 12 January at Test Stand "C" . 135 Bonner interview, 12 January 136Dates plates. for both tanks were obtained from their builder's JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 65) tetroxide tank) and an 80 gallon FLOX gas storage tank adjacent to the 186 gallon LF 2 tank (see Fig. 6).
To the east of the 256 gallon diborane tank was a 100 gallon hydrazine (N2 H.) "tank package," to the west was a gallon liquid nitrogen tank. The plan includes six drums labeled "charcoal disposal system" at the end of a fluorine vent line northeast of the caustic pond. The tank behind the barrier east of "c" Stand Tower was replaced by Building E-65 (Compatibility Test Building) in various metal alloys and components were placed into long-term contact with propellants to determine their compatibility on long space journeys. 137 In addition to facilities for exotic fuels, Test Stand "C" was provided a complement of support buildings in constructed in the vernacular manner of military temporary structures.
Building 4213/E-14, Test Stand "C" Shop was built in most likely for support to Test Stand it was reassigned to Test Stand and is reported to have been identical in form and plan to the Test Stand "A" ShOp.13B It is located at UTM coordinates is x and enclosed three rooms. Building 4213/E-14 The north facade double doors provide entrance to the large workspace on the north half of the structure; machine tools and a large workbench dominate the workspace. The room on the east half of the south facade is an office space; a closet for housing work clothes, especially protective gear is on the west half of the south facade, accessible from the office. An emergency shower and eyewash station is attached to the east facade; a chemical hood also is installed on the east facade.
Building 4217/E-18, Test Stand "C" Barricade, was constructed in to the immediate south of the test stand. Made of heavy timbers and backfilled with earth, the barricade protected Test Stand "B" from mishaps at the fuel tanks or stand at Test Stand For a few years, a small plywood hut perched on top of the barricade housed motion picture cameras (See HAER photo CA-163-D-4). The original "C" stand barricade was later replaced by a concrete-parged earth barricade designed to deflect shrapnel upward in the event of an explosion. 137It is interesting to note that even drawings done by the test stand engineers themselves still took account of the trees growing on the site (extreme lower left of Fig. 4 near the "High Press. 138 JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 66) JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 67) Test Stand Building 4223/E-24, was the first test stand constructed at the JPL Edwards Test Station following NASA's accession of JPL in As Test Stand nD n rose during NASA, JPL and other organizations began active planning to reach the moon, and JPL Edwards focused on reaching the Moon, Venus and Mars with unmanned craft.
Test Stand nDn began as a distinct, self-contained complex with an individual location on the cultural landscape (UTM coordinates Its tower centerline was situated 430 feet north of the centerline of Test Stand It followed the three cardinal planning principles that had emerged in JPL Edwards' evolution: response to prevailing winds, attention to intraline explosive quantity- distance limitations, and segregation of fuels and oxidizers. In the JPL newspaper LAB-ORATORY, it was reported that: They're building a new test stand with a water-cooled flame deflector for the static testing of the 6K propulsion system to be used in the upper stages of our space probes. Height of this test stand is about 43 feet.
It is referred to as the "D n stand and its completion will give ETS a total of four test stands. 139 The 6K liquid-propellant rocket engine placed probes and orbiters in parking orbit around a heavenly body, such as the moon, Mars, or Venus and maneuvered probes and landers, once they had achieved orbit. Test Stand nD n was the primary test stand where operational liquid- and solid-propellant propulsion systems for the Ranger, Surveyor, Mariner, Viking and Voyager spacecraft were tested. Also built at the same time was the Control and Recording Center (Building 4221/E-22, UTM coordinates and tunnels necessary to connect it to the two-year old test stand tunnels.
The new Control and Recording Center was a necessary safety precaution due to the hazardous nature of the testing conducted at the JPL Edwards Test Station. 140 The Center contained television monitoring equipment, recorders, and a computerized data acquisition and reduction system, some of which is still partially intact (see HAER photos CA-163-J-10, - 139 LAB-ORATORY April 140 Gibbons and Tibbitts, 4. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 68) 11) '" It was reported in LAB-ORATORY that: This system contains analog recording equipment and a flexible transistorized digital recording system, the MicroSADIC, with an initial capacity of 60 channels and a maximum sampling rate of samples per second.
Output is a magnetic tape suitable for entering into the IBM 704 digital computer at Use of digital computing will speed up data processing by a considerable degree. This building will eventually house all control and instrumentation equipment for the three existing stands as well as the new "D" stand."2 The Control and Recording Center is a x blockhouse built of reinforced concrete by JPL and the Dilworth Construction Company. It has approximately square feet of air-conditioned interior space on two floors. The interior is composed of two primary areas: an office and workspace with bathrooms and storage rooms on the west half, and a large control room on the east half.
The control room has a false or dummy floor to provide access to concealed cables (see HAER photo CA- and in the southeast corner is a stairway leading to the tunnel system. The north, east, and west sides of the center are banked with earth, its only access above ground being from the west (opposite to the test stands) for vehicles. A stair on the north embankment leads to a flat-roofed, polygonal observation booth located on the northeast corner of the roof, from which Test Stands lIA,1I IIB,'I lie/II and IIE ll are visible. The observation booth windows are bullet-proof plate glass.
The entrance into the observation booth is on the west facade, opposite from the test stands (see HAER photos CA-163-J-7, Test Stand "D" was initially constructed by the Structural Engineering Company of Azusa, California, along with the Test Stand "D" Workshop, Building 4222/E-23, located to the west of the test stand at UTM coordinates In the ensuing 18 years, five test cells were built at "D" stand, including the Dd horizontal test cell and Dj atmospheric test station in the Dy horizontal test cell in the Dv vertical test cell in and the Dpond atmospheric test station in the The x workshop has a 141 National Aeronautics and Space Administration and Jet Propulsion Laboratory. The Edwards Facility.
JPL Pasadena, California: Jet Propulsion Laboratory, November 142 LAB-ORATORY April JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 69) five-room plan, which is still intact with minor alterations. Two workspaces, an office, a bathroom, and a storeroom are present. The northern workspace has a large workbench on the north facade (see HAER photo CA-163-G-4). The original Test Stand "D" tower contained two 170-gallon propellant tanks; engines were mounted beneath the propellant tanks and fired downward.
A water-cooled steel deflector, or "flame bucket," at the tower base directed the exhaust gases eastward where prevailing winds carried the plumes away from the stand complex (see HAER photos CA-163-F-4 and In keeping with site layout principles established at Test Stand fuel storage tanks were located south of the tower, and oxidizer tanks to the north of the tower for safety (see Fig. 7). Only MMH (CH 2 ) was used as a fuel at Test Stand D, and nitrogen tetroxide (N 2 0.) was the sole oxidizer. The waste products from these propellants are water (H2 0), carbon dioxide (CO,), and nitrogen Hence, no exhaust scrubber was ever necessary.
Unused MMH vented from tanks and lines was neutralized in a tank of "Perchloron" [Ca(CIO), or calcium hypochlorite, in diluted form used as common household bleach) ; vented N,O. was eliminated by a natural-gas fired burner. In almost immediately after testing began at Test Stand the Dd (d=diffuser) horizontal vacuum cell and Dj (j=injector) atmospheric test stand were constructed on the east side of the "D" stand tower. The Dd cell with its steam-driven ejectors allowed JPL to test engines up to pounds of thrust at simulated altitudes from sea level to feet. Unlike the Corporal E and Sargeant missles which were fired only once in the earth's atmosphere, space probe engines were liquid-fueled engines intended to be restarted numerous times in deep space.
It became necessary to simulate the extremes of the outer space environment as well as possible in order to test engines and propellants for functionality. The Dj stand was a small steel table on which engine injector designs were tested. Construction of these two stations began in April and continued into early Ranger spacecraft had been under development since and JPL was signatory to a contract with Hughes Aircraft to build the moon-lander series Surveyor. Surveyor was intended to soft~land on the Moon, and development of a suitable vernier (throttlable) engine took nearly 5 years owing to numerous technical and managerial problems. "3 Test engines were installed or removed from the Dd cell via 143 Koppes, ,, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 70) - r . . .
'.. .~ r Fig. 7 Conceptual drawing of Test Stand "D" from cover sheet of original drawing set, 29 January . JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 71) a top hatch, using a fixed crane (see HAER photos CA-163-F-IO and CA-163-F-16). Propellant lines, instrument wiring, and fire suppression systems passed into the chamber through vacuum-tight flanges. Figures 8 through 11 present diagrams of "D" Stand fuel and oxidizer storage systems, the fuel run system and the helium system which "pumped" propellants to the test engines. Figs. 12a and 12b show the complexity of the nitrogen system which activated valves of the other systems. Vacuum-tight viewing ports in the Dd cell permitted test personnel to monitor tests via closed circuit television cameras.
Attached to the east end of the Dd cell was a diffuser, a water-jacketed exhaust gas cooling chamber with internal water injection cooling jets, and two steam-driven ejectors powered by a "Hyprox" steam generator (see HAER photos CA-163-F-14, The diffuser and water jacket consumed domestic water at gallons per minute The generator was fueled by a 360 gallon tank of hydrogen peroxide (H2 0 2 ) , mobile tanks of hydrogen (H 2 ) , and a 1500-gallon water tank--the exhaust from the generator was simply water vapor (see Figs. 13 and A steel barrier wall was built along the north side of the Dd station; two run tanks were on the north side and two fuel run tanks were on the south side.
The test chamber "train" was mounted on rails, permitting it to expand and contract with changing temperatures or the installation of different sized diffusers. The test train was aligned eastward so that the prevailing winds would carry exhaust gases away from the complex. A concrete-lined "neutralization pond" was built; however, it was never needed for neutralizing engine exhaust products or waste propellants. Perhaps as a result of the Ranger program, the difficulties with the Surveyor engine, and the initiation of the Mariner program, a "Y" branch and second horizontal vacuum cell were added to the Dd cell ejectors in (see HAER photo CA-163-F- The branch was "Custom built by C.E.
Howard Corporation" (South Gate, California) according to its builders plate, and with it The Dd and Dy cells could be isolated from each other and sealed off from the atmosphere after evacuation by butterfly valves installed between the cells and the ejector system. This permitted JPL to "soak" engines--subject them to long periods in vacuums--in order to ascertain restart reliably in the depths of space. The Dy cell was equipped with a jacket through which LN2 could be pumped, cooling the chamber interior down to better simulate the frigid depths of outer space.
Undoubtably, many designs were tested in the Dd and Dy cells before the successful launches of Mariner 1 on 22 July and Surveyor 1 on 30 May Mariner launches continued until while work on Viking, Voyager, and Pioneer spacecraft continued. One diagram discovered in the JPL files indicates that a solid motor test Co> , & ~-O--J\i,,' BELOW (I" " , ; 3"DECK .t" !P F .7 ;._ i ,;" ,'J .. : , 9 I,HIGH POINT BLEW ~- . ~ ~;'~i~r i-'-"-"+-~""""""~ .<,~,.;"~~;1f%1i' f" M.A ' .. '~?~I1J~{~;;:\;:2~., . "'- "':}i> ~ ~ ~~: ,,' A:F,~,.~~~~~:J;>~~ "'..tA ~h,~iJI . . '-< ~ '0 BrLO\,J r< ~' '. 1t.1"DECK c I~ .. '/; SW (ORNER . \-, t " ~ '0 FU I'-L .' 5TORAC?E:'J.';f?VM .S YSTE'r'!'- ~ .~.i'~ ~t3 f~~~i~; ~ ~': ~m~ "I-z.1- 70 :uro>~ Ul -0 '0' Fig.
8 PJ rt~ Fuel storage and pumping system diagram at IIDII Stand in I t"I -..Jf-'OH NO'\~1-3 -W-o-<; . -, ~ (jV .. :~: .. l - I . -;- .. _ .. .' .. _;- ... ~ --. re ;. _ . J . .. . - - . ~. " -.. ... - ' ..' ... ~ ~ ~/ ( . . r~ 8V..eIVE.R . - _. ~ _. . -'. - ." . '-. -~ . ... ; '- -;~ ; .. " . i. " , PSI. '" "Nv..O~ " #, .C ,. f __ . '" .. : ' I 0 m GN~ .. '-. " - , ' _. .. _. -- .. C-< .. : -.' . " -., "' L' " I:'J p,e; . :,- :- -i~~:--i;~.~:> ' .. :;: '. 1-' - . ' ".; - . ~L' " Ii .. on., , /-uc.n.....J -'. /, , ,.' , OXID/i!ER STORAGE /'. PUMPING 'SYSTEM , 66- ~Ol~ i r- " .. ' ,~:c,:::~,--~::._,~TE.M-"'~~ ,_iV. 2-Z~'lO Ul . ~O (}) "'J Fig. 9 ~ rtp LQ () PJ () lID II Stand oxidizer storage and pumping system roprtH I L' diagram in -...JI--'OH W<J'I::Jt-3 p' UPD~~.~~: .. .. , F &L$~i.~. ..
II' ~it~~N~.~~--~;~'~ ('-F/~~"'{',4.1AJ#' '. < ~;i:jJltllf ( .c , --' .;i~~:i!-~i:t,~t.,); , :t ~~IQ,.,1..r. "'" y ~' '11 mw t"' ~, I t>:I '.' D' o.e., ~/I.L. I'I'Lf'e :;; '11 ., PJ t"' FUEL .RUN SYSTEM " O<t>:I 6G ELP 033 DLB ~WiJ ITEM G :u:i~ nW ~~ ~b~ I ~ , -0 (J) '%J W lOnPJn Fig. 10 ro;x>rtH "D" Stand fuel run system diagram in I ....,JI---iOH the oxidizer run system is similar in outline. ~"I'~"'"'' ~, " 'f r~ l ' ,-, i - j' '-t,-I- :: t-" )I , 1 ., ,- r . :~ ,. i ) ;~- . __ i~ '. . 1 f; I : MES$~J( I. ' : .", : :" ;L1Ne ~$l.r;U:_. - . L-> : - _-: __ t_,:_':l:L~~~~~I : ' ~ , i': f~ Ub~b:~ ., .~" I; . .,. ,: . . ' I .'" ,. . t;.NO/t "I . ~ , . ~ r. /'1 ~ I 't .- - , I p, .. i 1 " c . ~ -- "'t"5.e',,~t.a's. , ?I'~ I -. __ ,.Fib!". I nr.!luY'f ! Ildl : _. I' . ..
-i,~I-t-il" .; H-i+.1,-,.--- c" " _ . . . . . ,, ... ,i :.. __ ., I... ,. jil. . , , . ' -t..:..t--L-+-I~i1 ~ -~--~i/o7i&J:;m~~~ ,~~~~A~.W H I 1", :-~ r ; _- tT : /I1 L. -a~(f . .PY'.~RoP: PiJIZGr. _1 ~-- . _. r !-T _ .,-r-~I'":" i. --I " ;:- .-. I;' ;' 1 I -f- " .-. '0 t< .. __ o~ip Y~H 1 ! , -I: ~i_:: i:'l .!. I' ' . -'. '-I ' ,', I I :e: '0 , -. ! ! J},S1A,~> f-\ l1 ! -1 1 IlJ t< 'i p.i:'l I I ; /, ,. .. /lI.6 " I i,_ i : i I ~IDg i _ . REV"'O 10 1+' , IDO -0 ~, '0' CIl "l IlJ rtp Fig. 11 lQ n IlJ n , t< Diagram of helium system at "D" Stand in -JI---l'OH JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 76) Fig. 12a Left half of "D" Stand nitrogen gas ) system in (Use match line shown to connect with Fig. I JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 77) ~ ~ i " :: ""~ ~~ 0 " " 0 ~ v q ~. :l . , I? ... v <~ ~ t~ "' ~i 1;' I:irI ... v~ , i!. ~rH WI< VW D. VA(UlIM 'liMP I'-il<>2 )(. STAG~ v ,wT " ; l>j BVLI( /) 5YSTEM (D-STAND) - ELP - 033 - DLB I ,"rEM 2. 13 '! 4-_ d - 14 RfVIO_IO-74 Fig. 12b Right half of "D" Stand GN z system diagram in (Use match line to connect with Fig. 12a) JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 78) I " i, ," I >. ~ I i .u ''; l l. <i: : . ''; () III I . ~ I J:: ; 0 ''; .u >- / III ;:l ,id l- E z :J " ~ ''; 0 i= (3 if "I ~ Cil ~ z ~ I, If Ij) '" 2 rl ;:l l- r .u 0- W !:< ., , ''; tn.u :0: u; I ''; ~ ~ = '"0 a: w ;, ~ ~ 0:> 0 J:: 0 l- w ;:: ''; .u ... -J ~ III .u ~ OJ = 1 ~ '0 i=1 ! ~ I ~ E III ~ '. ~ " 01 III 1 ''; i=1 '" ITUl Jo1 <M. ~ ~ ~ ~. It mJ 'OU'< !'/i'~ ~~ "'to...
I '1J 0, HYPROX SYSTEM t"' 66-ELP-033-DLB t>:I ITEM 14-PAG( I 12 II 69 - ", ... ~ .. - ' " I t"' " '1J IlJ fi P,t>:I ~Ul~ -r- :W ~~STEJ,M i:':I~:J> ~q "UI"Ii'rLI~ :<lro?:J Ul tl ZrtUl ~O Ul"'l IlJ Fig. 14 1 t"' Diagram of "Hyprox" system fuel and steam lines in ...Jt-JOH JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page 80) ~: IU---. , -. 0'\ rl I M c-- 0'\ rl E 0 ;, "-' p. ~ ..,I Q) {f} r LJ) rl .~ 0 ~ E .., {f} .., Q) '0 rl 0 Ul rl rl Q) U r I t~ ~ I '0 Q U "'. _ .. ..J "-' 0 E n:s H tn JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page 81) setup was planned for the Dd Cell in (see Fig.
During JPL Edwards' concentration on the development of liquid-propelled engines, JPL headquarters decided to move its solid-propellant testing facilities from Pasadena to JPL Edwards in Plans were drawn accordingly for Building 4259/E-60, Solid-propellant Test Stand "E," which was built in Test Stand "E" was located further north of Test Stand "D" along a third-phase tunnel extension, following the industrial land-use design principles outlined earlier. More discussion of the mission and design of Test Stand "E" follows later. During the construction program at JPL Edwards suggests that the facility was preparing for a still higher volume of test programs.
Building 4262/E-63, a cubic foot liquid nitrogen storage facility built to the west of Test Stand "C" in was augmented by the addition of a manunoth cubic foot liquid nitrogen "Driox" tank built by the Linde Company of Union Carbide. This addition to the JPL site came within months of the completion of the new Dy cell at Test Stand "D" (which was equipped with an LN2 cooling jacket), and the construction of Building 4270/E-71, a liquid propellant storage facility. The build-up of capacities for nitrogen (essential to propellant controls) and propellants was prodigious. In JPL converted Building 4270/E-71 to Test Stand extending foundations and erecting a tower reminiscent of Test Stand however, Test Stand "F" was never used for engine firings.
The year brought the first manned landing on the Moon, two successful Mariner missions to Mars, and major expansion projects at Test Stands "C" and However, the National Environmental Protection Act and the Clean Air Act were working their way through Congress, and public attention to manned moon- landing spectaculars began a multi-year decline. Plans were drawn for a third vacuum cell at Test Stand including a large three-stage ejector system. A toxic exhaust scrubber facility was designed for Test Stand Construction at both stands appears to have overlapped, though a voucher for work completed at Test Stand "D" was paid on 24 April work was continuing on the scrubber system in photos dated November (see HAER photo CA-163-D-6) .
In the original Test Stand "D" tower was enlarged and its fuel tanks and original flame bucket were removed. The basic four~story, braced, steel I-beam structural framework with a metal stair on the north facade was retained. An 8-foot diameter stainless steel vacuum chamber built in by Capital Westward, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 82) Inc. of Paramount, California was modified and installed vertically in the tower to test engines up to 400 pounds thrust. It was capable of simulating outer space conditions (vacuum, extreme heat, and cold) between sea level and feet of altitude. Similar to the Dd and Dy stations, the Dv cell permitted test personnel to "soak" engines.
After removing the chamber top, a Shepherd-Niles hoist (Crane & Hoist Corporation, Los Angeles, California) of pounds capacity extending from the top story of the framework, lowered spacecraft engines into the vacuum chamber for vertical firing. Instrument wiring, stainless steel fuel, oxidizer, and control lines were connected to the rocket engine through vacuum-tight flanged ports in the chamber walls. Figure 15 shows the piping diagram for a "V.O.- 75" (Venus Orbiter) engine in the DVCel1 in Test personnel entered the chamber via a large flanged opening with a cover secured by multiple bolts. Personnel could not open the cell until it contained 19 percent oxygen.
The cell was enclosed by an insulated air plenum by which it could be heated externally; internal panels circulated fluids near test engines to simulate extremes of heat and cold. A three-stage air ejector system with an interstage condenser was built by Croll-Reynolds Co. and erected on the east facade of the tower to evacuate the Dv cell for simulated high altitude tests (see Fig. The system was driven by steam at 300 psi; however, the steam and engine exhaust which carried over from the first two stages (X- and Y-stages) met with counterflowing sprays of cold domestic water in the condenser. This not only resulted in a less spectacular cloud of steam (such as could be seen when the Dd train was in action), the condenser was of considerable help to the x- and Y-stage ejectors.
As steam was condensed, a vacuum was created in the condenser, helping to draw in the engine gases and ejector steam, since they were not resisted by normal atmospheric pressure (as at the Dd and Dy ejectors). The condenser removed the steam from the gas flow, leaving only the non-condensible engine exhaust gases to expel into the atmosphere. Normally, one of the two small Croll- Reynolds Z-stage "Evactors" on top of the condenser would be sufficient to this task. The second, or ejector could be turned on if needed. The condenser was referred to as an "interstage" device because it operated between the Y- and Z- stage ejectors. Condensates drained into a hotwell at the base of the "D" stand tower via the condenser's "tailpipe," and from there into the pond.
Because of the vacuum created, the condenser was mounted high on the Test Stand "D" tower, so that its iowest point was at least 35 feet above the water level in the hotwell. This prevented the atmosphere from forcing water into the ejector system from the hotwell (average atmospheric ~l~ ~ 1 11 I IITTI/(.tlf'1EAlr:r .38'1i "73 .i6" .K I el""': E'---i' ,I ) . fir ~~-'i!~f--~l'-ch=--4'-~~j.-- , .. ., &. ~':I'l. ~". .. ~ ..",r\.l;!J<lo1 I TA;)I<'- ,- .-, "" r< ' i . ., I ,., I. ... <$- / '" -\ I \", ";0 c, '(j t-< '"1 ~ . :: T' t~~ riU.. I I' a. T I'll __ ~, ~.I~' TO I'If'()Pf;LLAA/r _ ( Il--&--U-."'-=n-- OJ t-< .. ~ I ~ I fi ~ T<I$_Ur,,4E TA ~Ul~ Fl,Ia, SYSTEM- VO"7S DV INSTALLATION ro-z'-73 OXID. SYSTEM tt:I'c3:J> Ult:! lZi ZrtUl o Ul ":I Fig.
16 OJ Diagram showing fuel and oxidizer line installation I in the Dv Cell for Venus Orbiter engine test in COI--'OH JPL-EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 84) I'. . .; ~ . . . . .Y STAGE STEAM YSTA.-:.G::..E_-t----t /Joo GPM clli' 1M CONOI!NSER ..v I MMN WAT.~ STIiAM HOT WELL VIV VACUIIM ISOlATION t:'LAMI! COOliNG \ oJl,otr "Pv TYP . TES T CElL Hz PURG(! VN- ,I TEST ITeM .' X STAGE STeAM VACUUM EJECTOR (0 STAND) Up 033 IUM YZ" - 3 SMAY '75 (A.H.) Fig, 17 Schematic of 3-Stage Ejector System for Dv Test Cell. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 85) pressure will support a 32-foot column of water}.
(HAER photo CA- shows the Z-stage ejectors in operation during a test.) At some point shortly after the Dv cell was erected, the 24- inch diameter vacuum line at the bottom of the cell was extended and connected to the "Y" branch on the Dd train, ahead of the Dd ejectors. In addition, a large GN2 actuated gate valve was installed between the Dv Cell bottom and the junction between the vacuum pipes to the tower ejectors and the Dd ejector. The vacuum line extension allowed the Dv cell to use the Dd ejector system for tests (or add in the tower ejector system as well), while the gate valve could isolate the Dv Cell for lengthy vacuum Ilsoak tests.
ll Over at Test Stand the imminent national air quality laws seems to have spurred JPL to find means of eliminating HF, and boron compounds from exhaust gases released into the atmosphere, in order to continue testing for longer times on larger scales. Accordingly, Frank C. Brown & Company, Inc. was called on to upgrade the atmospheric test station with a design for a "Toxic Exhaust Scrubber Facility." This equipment was installed in at Test Stand "C" (see HAER photos CA-163- Known facetiously as "Flushing Meadows" at JPL Edwards, this scrubber is claimed to be the first of its kind in the United States. 144 Included wi th the scrubber was a large reinforced concrete "Treatment Pond" designed to contain between and gallons of 1.5 percent (by weight) sodium hydroxide (NaOH) solution.
A schematic of the equipment process appears in Fig. 18. The scrubber tower was made of mild carbon steel, as well as the cooled and uncooled ducts which conducted corrosive exhaust from a test engine to the scrubber tower. A test engine would be mounted on a securely anchored table near the western end of the scrubber's intake duct, and the engine nozzle would be inserted into a diffuser, somewhat like a funnel, that directed all exhaust products into the duct. Air from the surrounding atmosphere was also entrained, and temperatures of the subsonic exhaust gases reached approximately Fahrenheit.
The first segment of the diameter duct, cooled by a double-walled steel jacket, injected NaOH solution into the exhaust plume through 24 stainless steel nozzles at a rate of gpm after the NaOH circulated through the jacket. In addition to cooling the exhaust gases, the NaOH was intended to absorb HF (and/or , as well as uncombusted fluorine and boranes. The NaOH reacted with the uncombusted fluorine and 144 Gibbons and Tibbitts, 1; "Flushing Meadows" is stencilled numerous places on the scrubber and Cv Cell tower. AtmospheriC Key to Symbol'~ Vent 1:1 Orifice Exhaust Scrubbing ~ Pressure Gauge Fan Tower Pump Strainer " " ~ AdaPter Demister. Packing ~~'~~'~11'iJ v Check Val v e 'CA(OH)2 .rc Plug Valve i~~~i~i~~J .I " Cooled Duct . Truak -< Spray Nozzle B 2 H H2 He S Air I IU -. I \ .
Uncooled l?uct \. Tank --:>o<:-~." .fO'<".,.{ - - ~ _/ ; ~. fi~ m ,r \ ! ~/ c: r { I. niP I ... I Splash Plate I OF2 Air I c., Rocket Englnel '0 Test: Setup Tower Out lets t' .SlU8ge t1J Pump ~ '0 Ult-' Treatment Basin "o.t1J, A ~to~ (/l tJ oZr1"'" '0. (j) "J Fig. 18 Ul rt >' w Hn en(1) pn rt Schematic Process Diagram of Toxic Exhaust Scrubber Facility , t' OOI--lOH '"w - '" ::l <-3 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 87) boranes to produce more benign compounds like sodium fluoride (NaF) and sodium borate (Na 2 B.O,) in aqueous solution (or even common table salt, NaCl, when chlorine penta fluoride was used).
The second duct segment did not need a cooling jacket; instead it contained 24 PVC (polyvinyl chloride--a common late 20th-century plastic plumbing material) nozzles arrayed in a "Christmas tree" fashion to inject gpm of NaOH from a supply pipe centered at the duct axis. The duct was inclined so excess NaOH solution would drain into the scrubber tower by gravity. The scrubber tower was a mild carbon steel tank in diameter and approximately high.
At its top was an axial fan that drew scrubbed gases from the inclined duct through the unit and blew them into the atmosphere; the cleaned gases consisted of carbon dioxide (C0 2 ) , nitrogen , and water vapor Counter to the gas flow, NaOH solution was sprayed at a rate of 500 gpm over an 84-inch deep bed of polyethylene spirals called "Tellerettes" at the bottom of the tower, through which the exhaust gases had to pass on their way up the tower. The tellerettes helped provide an extensive surface-area-to-gas- volume ratio for the last traces of toxic compounds to be absorbed. NaOH solution flowed by gravity into the bottom of the tower, which opened to the treatment pond beneath the pond's surface, at once providing fluid circulation while sealing off any gas leaks.
The tower contained an upper level of dry "Tellerettes," 12 inches deep, designed to deflect entrained droplets of NaOH out of the gas stream before gases left the tower. The scrubber facility and "caustic pond" (as the treatment pond came to be called) were designed to handle up to pounds of propellants per second for as long as seconds. This was equivalent to firing an engine of pounds' thrust. Further neutralization of the absorbed reactants was accomplished by adding slaked lime solution--calcium hydroxide Ca(OH)2--tO the contents of the bottom of the tower from the hose of a tanker truck.
What resulted from this stage of treatment was an insoluble, nontoxic sludge of calcium fluoride (CaF 2 ) , calcium tetraborate (CaB.O,), and reconstituted NaOH solution suitable for recycling in the process. According to John Richard Bonner, a test stand engineer at the Edwards Facility since the the pond was "mucked out" twice in his career by hand, and it had about 8 inches of sludge in it each time. This atmospheric test station continued to operate with no major modifications. If NaOH was needed in the "caustic pond," JPL personnel simply added it by hand in dry form from cardboard boxeS, rather than by tanker truck as illustrated in Fig. 18. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 88) The NaOH concentration was monitored with a pH meter.
'45 In part as a result of JPL Edwards research, the rosy future anticipated by advocates of boron fuels in the darkened, and finally collapsed. Research revealed a bevy of problems: many combustion products from diborane, dihydrotetraborane ,o )' pentaborane, and hexaborane (B 6 H,o ) were found to be toxic to the human nervous system, or systemically poisonous, and cumulative in their effects. 146 In addition, the boranes were discovered to "disproportionate"--within the same propellant tank, pentaborane (a disagreeable, spontaneously flammable gas condensing at OOC/32 F) would convert spontaneously to decaborane (a solid melting only at lOQoC/2l2 F or higher) while in storage. ' " This characteristic made it highly unreliable and unsuitable for long space missions. The U.S.
Congress funded a million plant for the production of hydroborane fuels for use in aircraft, only to cancel the project as it was nearing operational status. 148 The present atmospheric test station at Test Stand "C" is the final evolutionary phase of the original Test Stand "C" installation. It came to be used primarily to test propellant injector designs and patterns. As is apparent from the volume of facili ty photographs, the JPL Edwards photographer'49 was kept busy constantly photographing the effects of various tests on injectors, engines, equipment, and specially engineered materials.
Detailed piping and equipment schematics were 145 Bonner interview, 12 January 146 Moran, Cliff, JPL Pasadena, California, telephone interview with Richard Anderson, 20 March, 147 Moran interview, 20 March 148 Moran interview, 20 March 149 The JPL photographer from to was George Emmerson; between and July the JPL Photography Department was responsible for coverage (the individual photographers were not identified on JPL images); from July to the present, William C. Tibbitts was the facility photographer, and he estimates that 90 percent of the photos taken at JPL Edwards during this time period were made by him. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-l63 (Page 89) recorded for all test set-ups Tests were also conducted in separate structures on the long-term effects of propellants on various materials that might be used in spacecraft. Normally, four JPL employees maintained and operated the test stand. After the personnel were stationed in 4221/E- 22, Control and Recording Center, for safety purposes during test firings, which were observed via television and remote-controlled photography. Electrical systems for instrumentation ran at 28 volts direct current relying on a battery in Building 4213/E-14 for power; volts alternating current (AC) was used for lighting, and small pumps; the 100-horsepower caustic solution pump, which delivered gallons per minute, ran on 460 volts (3-phase alternating current) at 117 amps.
Set-up time and costs for a test varied depending on the quantity of pre-existing tubing and equipment that could be reused. Stainless steel alloys 321 and 347 151 were used for propellant lines to resist corrosion from propellants at room or cryogenic temperatures. Stainless steel tubing was also used for high-pressure GNz ' LNz and helium (He) lines. After tubing was bent to shape and coupling fittings attached, interior surfaces had to be thoroughly cleaned of all lubricants, dirt, and other contaminants. Not only could such substances react explosively with propellants, dirt particles could clog tiny orifices used to control propellant flow rates. Fuel lines (such as were cleaned with a mixture of isopropyl alcohol and de-ionized water, then dried in a vacuum.
Oxidizer lines were cleaned with freon (a refrigerant, dichlorodifluoromethane, z ). A service cart containing these cleaners was devised for cleaning lines already in place on the stand (see Fig. Once cleaned, parts were 150 The authors presume that equally detailed extensive data were retained on all tests, but in-depth analysis of test history and results was beyond the scope of this documentation project. Such an analysis would no doubt yield a more thorough history of each test stand as well as the specific engines, programs, personnel and other subjects of interest.
151Alloy 321 (American Iron and Steel Institute numbering system) contains percent carbon (maximum), to percent chromium, to percent nickel, and titanium at a minimum of 5 times the carbon content, the balance being iron; alloy 347 contains percent carbon (maximum), to percent Chromium, to percent nickel, and columbium and tantalum at a minimum of 10 times the carbon content, the balance being iron. Both alloys are austenitic. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page 90) ALCO-H. PP. PSI CAP. 'I GLS FREON R~J ViP. JOOPSI CAP. 9 Fig. 19 Schematic of Solvent Service Cart used for cleaning propellant lines . JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-l63 (Page 91) bagged (ends of tubing and fittings) for transport to their installation points.
Once assembled, the air in tubing, valves and ancillary fittings was flushed out with GN2 and the system pressure-tested for leaks. A gas-detecting liquid designed to produce telltale bubbles at leakage points was brushed onto joints. Propellant lines were not only flushed with the escaping nitrogen was tested with a hydrocarbon analyzer for the presence of solvents, and a "dewpointer" was used to check for the presence of any moisture. Tubing was then capped off (or a valve closed) until propellants were introduced. Fluorine was introduced to passivate the walls of oxidizer tubing before the tubing was filled and pressurized for use in a test'52. All valves for propellants were actuated with high-pressure GN2 not electricity, for safety and reliability.
Nitrogen is used because it does not react with the propellants, and is non-toxic and non-corrosive to equipment and personnel (the earth's atmosphere is 80 percent nitrogen). Propellants (especially cryogenics), however, were driven by high-pressure helium gas, which is chemically inert and does not liquify except at extremely low temperatures F), well below those of any cryogenic propellants. Because helium is used to pressurize spacecraft propellant tanks and "pump" propellants to engines, fittings called "bubblers" were fitted to each propellant line to saturate the propellant with helium gas. This affected propellant and engine performance, but in a way that reproduced conditions aboard spacecraft in deep space.
Most tests were very short duration--5 to 15 seconds, but set-up time could run into the hours or days. Evaporated propellants (as from warming cryogenics), fumes, etc. were vented from tanks and propellant lines to various disposal mechanisms. Boranes were vented to a natural-gas fired burner that rendered them harmless. Fluorine and FLaX were vented to the scrubber facility, or in emergencies, to 55-gallon "burn barrels" filled with activated charcoal. Other oxidizers like nitrogen tetroxide were vented to natural-gas fired burners also. Mono methyl hydrazine was absorbed in reaction tanks filled with Percholoron (Ca(CIO)2) Liquid nitrogen and liquid oxygen were vented to the atmosphere. Lines were flushed with GN2 if test facilities were to be idle while extensive changes were made.
A test installation could become a maze of tubing, wiring and devices (see HAER photo CA- 152Passivation produces an anti-corrosive coating on a metal surface as a result of exposure to a gas- or water-borne chemical; after passivation. the chemical causes little or no further corrosion. In the oxidizer tubing, fluorine created a thin coating on the stainless steel tubing wall surface which prevented further corrosive action by fluorine. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 92) To confound the visual confusion for laypeople, disused tubing was usually left in place--"they gave us the money to put it up, but never any to take it out. The modifications to Test Stands "C" and "D" seemed adequate for several years.
During the coming years, testing continued for the development of Viking and Voyager spacecraft engines, and JPL seems to have gone on a quest for higher vacuums or better simulations of deep space environments. The steam supply at Test Stand "D" was augmented in by four natural-gas-fired Clayton Steam Generators (water-tube flash boilers) which provided pounds of steam per second to the Dv ejector system. The steam generators were housed in Building 4280/E-81 (UTM coordinates a steel frame structure with corrugated metal walls and roof--perhaps a more up-to-date equivalent of the inexpensive temporary military construction used for earlier ancillary buildings (see HAER photos CA-163-H-l to 4). The building was supplied by Soule and erected by E.C. Morris & Son, Inc.
(Lancaster, California). Plans were also laid for a second large horizontal test chamber and ejector train at Test Stand "D" in This facility retained the designation because it reused the 10-year old jacketed Dy vacuum cell. Similar to the Dd train, the new Dy train was set on rails so it could accommodate changes in length caused by temperature fluctuations or different diffusers. Added to the Dy cell were a water-jacketed diffuser, a cooling section containing water injection nozzles built by Croll- Reynolds, followed by a single large steam-driven "Evactor Air Pump", also built by Croll-Reynolds. This station was intended for testing solid fuel motors, but it was reportedly rarely or never used.
In following the successful Viking missions to Mars and two Pioneer missions to Jupiter, JPL embarked on a second campaign to upgrade and increase the capabilities of Test Stands "C" and Plans were drawn up in August for a substantial addition to the Test Stand "D" steam supply, followed closely by the addition of a vertical vacuum cell to Test Stand At in diameter, the Cv (v=vacuum) cell was larger than its predecessor at Test Stand "D" in order to accommodate larger engines, and was connected to the Test Stand "D" ejector system via an underground duct. At Test Stand a concrete pad was poured in the summer of for a 12-foot diameter sphere--an insulated steam 153 Bonner interview, 12 January JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (page 93) "accumulator" with three 100-kilowatt Chromalox electric heaters ordered from Capital Westward, Inc. of Paramount, California. Designed to provide a 100-second, 300 psi steam supply for the ejector systems at Test Stand the accumulator was cross- connected to the Clayton flash boilers in Building 4281/E-81 so that either steam source (or both together) could be used at any test cell. The "Hyprox" steam generator was removed. Installation of the steam system addition was completed by early To complement other spacecraft test programs, JPL personnel built a small test table, "Dpond," in the on the north side of the "neutralization pond.,.154 Small altitude thrusters (5 pounds thrust or less) and various non-firing components were tested there.
A small flame bucket directed engine exhaust into the pond. Like its predecessor at Test Stand the vertical Cv test cell permitted JPL to "soak" engines. They were maintained in a vacuum at various temperatures for extended periods in order to test their operational reliability. The vacuum chamber was a flight simulator for flights from sea level to feet under simulated outer space conditions (vacuum, extreme heat, and cold) using fluorinated and non-fluorinated oxidizers. After removing the chamber top, a 10-ton hoist, extending from the top story of the framework, lowered spacecraft engines into the vacuum chamber for vertical firing. Usually a diffuser was connected beneath each.engine nozzle and the bottom duct of the tank to collect exhaust gases.
Instrument wiring, stainless steel fuel, oxidizer, and control lines were connected to the rocket engine via vacuum-tight, flanged ports in the chamber walls. Engineers and test personnel entered the chamber via a 48-inch diameter flanged port on the west side. A 36-inch diameter steel vacuum duct connected the Cv firing station to a new scrubber-condenser tower erected on the eastern edge of the caustic pond. The scrubber-condenser was built by Croll-Reynolds of Westfield, New Jersey. Before firing an engine in the Cv cell, the cell and its vacuum ducts were evacuated by air ejectors at Test Stand "D" via a 30-inch diameter underground duct. The ejectors, which emptied the system of exhaust gases, remained in operation during firings.
The scrubber-condenser was essential to removing fluorinated exhaust compounds before the remaining gases were drawn to the Test Stand "D" ejection system, 154Dpond and the vacuum systems at "c" and "D" stands were designed by J. Richard Bonner. Bonner interview, 12 January JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 94) which had no means to absorb and neutralize toxic byproducts. Most firings lasted between 5 and 15 seconds, with some lasting as long as 30 seconds. Mono methyl hydrazine or NH2 ) was used as fuel in conjunction with N2 0. or F 2 The waste gases from non-fluorinated propellants are water (H2 0), carbon dioxide ), and nitrogen (N 2 ); hydrofluoric acid was a byproduct when fluorinated oxidizers were consumed.
Exhaust gas heat from Cv Cell tests was dissipated in several ways; first, domestic water was sprayed into the bottom duct of the vacuum chamber through hundreds of small holes in the deflector at the vertical duct bottom. The double-walled steel deflector elbow was cooled by circulating domestic water. Seventy nozzles sprayed 1.5 percent NaOH solution from the caustic pond onto the exterior of the 36-inch diameter horizontal steel duct to the condenser tower. A gallon-per-minute Borg-Warner Byron Jackson vertical pump delivered the NaOH solution, which returned to the pond under the duct by gravity. A lOO-horsepower Holloshaft pump motor built by Emerson Electric of Los Angeles, California drove the pump at revolutions per minute.
The scrubber-condenser tower scrubbed exhaust of raw propellants and fluorine compounds by passing a shower of NaOH solution through the condenser against the gas flow. Absorbed compounds and NaOH solution returned to the caustic pond via a l2-inch diameter vertical drain pipe while CO2 and N2 continued to the Test Stand D ejectors. The condenser is elevated over 35 feet above the pond surface in order to prevent the atmosphere from forcing the NaOH solution up the drain pipe and into the vacuum system. To soak an engine, a butterfly valve near the condenser scrubber was closed, and the vacuum in the Cv Cell maintained by a 15 horsepower Beach-Russ rotary vacuum pump at the "C" stand tower.
Two 6-inch diameter long lime (CaO) tanks purged fluorinated compounds before they could contact and corrode the pump. At the conclusion of a test, GN 2 from a purge tank flushed the chamber of any exhaust gases before personnel opened and entered the system. As at all other test stands, propellant valves were operated remotely by high pressure GN2 lines and propellants were "pumped" by pressurized helium. Cryogenic fuel and oxidizer piping were jacketed in LN 2 lines maintained at minus The JPL Edwards Test Station contains numerous other 155For comparison, at atmospheric pressure the following gaseous substances liquefy at the following temperatures: He, F; LH2 , F; LF 2 , F; L0 2 , F; LN2 , F; B2 H6 , F; CIF" F; -13 F; N2 H, , +34 F. JPL EDWARDS FACILITY Edwards Test Station} HAER No.
CA-163 {Page 95} buildings which support the testing and the general operation of the test station. Buildings 4225/E-26, Blower House No.2; 4226/E-27 Helium Compressor Facility; 4227/E-28, Booster Pumping Station; 4228/E-29, Water Tank, which has been demolished; and 4229/E-30, Generator Building were built in in conjunction with Test Stand "D" to enhance the operations of the overall test station.
Test Stand nE" and the Solid-propellant Processing Line The JPL Edwards Test Station grew at an exponential rate in the early The growth was centered on the addition of solid-propellant rocket motor manufacturing operation, which was moved from Pasadena to the JPL Edwards Test Station in the early The solid-propellant manufacturing and testing facilities were primarily built by Greynald Construction of Sherman Oaks, California and the Ruane Corporation of San Gabriel, California in and The addition of the solid- propellant processing operation brought an influx of JPL employees to the Edwards Test Station in the early 97 employees worked at the JPL Edwards Test Station at its zenith in The ETS solid-propellant manufacturing capability was NASA's only in-house solid propulsion processing and testing facili ty.
156 Between and a new security fence was erected, approximately 575 acres was added to the JPL Edwards Test Station complex, the solid-propellant processing line and Test Stand E were constructed, the storage area and new docks were constructed, a new administration building was built in the complex's southwest corner, and an aircraft hardstand and taxiway which linked the JPL Edwards Test Station with the North Base runway was added. The capability to park aircraft at the JPL Edwards Test Station facilitated quicker access to the JPL laboratory in Pasadena. This was by far the largest single expansion program ever undertaken at JPL Edwards. The JPL Edwards Test Station became a large, extensive complex when the solid-propellant processing line was added.
The size is a reflection of not only the need for additional buildings, but also safety concerns relating to the hazardous nature of rocket engine and motor testing. The cultural landscape reflects an overwhelming preoccupation with intra-line quantity-distance limits and personnel safety at the JPL Edwards Test Station; it is a landscape filled with constant visual, 156 Gibbons and Tibbitts, 2. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 96) auditory, and architectural reminders of the danger and hazards of testing rocket engines and motors. Warning lights, the intercom system, air horns, emergency shower and eyewash stations, blast barricades, fire and chemical hazard symbol signboards, and test-in-progress safety signs abound.
Unlike the liquid-propellant test stands, the layout of the solid-propellant line doesn't seem influenced by prevailing winds, except for the location of Test Stand "E." Blast barricades were placed in conjunction with buildings that had a greater likelihood of exploding. The blast barricades were not designed to stop or contain a blast, but to check flying shrapnel. Blast barricades are located on both the north and south facades of Building 4233/E-34, the solid-propellant mixer building, since it was located too close to the administrative building. If the building exploded, the personnel working in the administrative building were potentially threatened. These high metal barricades are filled with native soil.
Two other types of blast barriers were built at the JPL Facility: the poured concrete barricade such as at Test Stand "B" and "C" and the plank barricades located at Test Stand "A" and Building 4234/E- 35, Building 4242/E-43, and Building 4272/E-73. Blast barricades are also present at Test Stand "A," Test Stand Test Stand Test Stand "E," Building 4234/E-35, Building 4242/E-43, and Building 4272/E-73. The architecture and spatial organization of the solid- propellant processing line also reflect safety concerns. The buildings are constructed from non-combustible reinforced concrete block and are windowless. Large steel doors are the primary entrances into the workspaces. The solid-propellant buildings have simple floor plans, most are two-roomed structures.
The first room is the workspace; the back room is the machine room, which contains the equipment operating the building'S systems. This floor plan offered not only the standardization of functions, but also architectural simplicity for firefighters and emergency personnel. Frangible walls that are easily broken are present at many buildings along the solid- propellant processing line. Buildings 4233/E-34, Mixer; 4236/E- 37, Mixer and Casting Building; 4237/E-38, Oxidizer Dryer Building and 4243/E-44, Remote Preparation all have frangible walls. Emergency slides, a common industrial safety precaution, are present on several buildings to provide egress from roofs and second floors. The Mixer, Building 4233/E-34, has a rear emergency slide on the west facade.
The solid propellant processing line is extensive-- approximately 40 buildings are spread between two major areas. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 97) The storage area dominates the east side of the complex; the manufacturing and testing area composes the west side of the complex. The volatile nature of the complex has resulted in a spacious industrial land-use pattern. Unlike the structures in the liquid-propellant testing area which are tightly clustered together relatively speaking, the solid-propellant buildings are located approximately 100 to 300 feet apart. A spread out complex would potentially help contain an explosion or fire to a single structure.
One exception to this pattern is the preparation complex which was for preparing solid-propellant motors. However, blast barriers and frangible walls protect the preparation complex buildings. The solid-propellant processing line structures are clustered by function: the cure buildings are adjacent to each other and the conditioning structures are contiguous, Along the remotely operated solid-propellant processing line, fuels and oxidizers were ground, mixed, and cast as solid- propellant rocket motors. The motors were then cured, conditioned, and test fired. NASA Standard Igniters (NSIs), necessary to ignite solid-propellant motors in space were also prepared at the JPL Edwards Test Station.
The propellant- processing facilities were dedicated for propellant ingredient weighing, and oxidizer drying and grinding. Five remotely controlled Baker-Perkins mixers provided propellant mixing in quantities ranging from 1 pint to 150 gallons. Four walk-in ovens cured the solid propellant, walk-in temperature chambers conditioned the solid propellant, and hammer mills ground the oxidizers. A Liner Laboratory provided experimentation space and housed the solid propellant office, A control building managed the processing line and contained facilities to weigh the solid propellant.
A x autoclave allowed the curing of solid materials up to 400 0 Fahrenheit, The solid-propellant processing line contained the necessary solid propellant measurement devices, including an X-ray Facility for inspecting solid propellant motors for cracks and voids. 157 The composition of solid propellant motors is "a bit of a black art" according to JPL personnel, The solid propellant processing line includes a test stand to test solid propellant rocket motors. The Ruane Corporation constructed Building 4259/E-60, Test Stand "E," in It is a x steel-reinforced poured concrete structure with a four-bay plan (see HAER photos CA-163-I-l, -2 for drawings) located at UTM coordinates Test Stand "E" 157 Gibbons and Tibbitts, 2, JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 98) consists of two individual atmospheric solid-propellant rocket motor firing cells and an X-ray inspection cell (see Fig. 20 for a simple plan). The two rocket motor cells are located on the north half of the test stand, and the X-ray inspection cell is on the south facade. The north bay is open on the east facade; it contains a large metal work bench and a 2-ton steel I-beam hoist. A remote camera is trained on the work bench. A corrugated metal sheathing covers the north bay. The adjacent south bay has tall concrete walls and an upper divider for separating equipment and tests. It has an open roof, and is open on the east facade. The center bay was used for vertical and horizontal rocket motor firings. An octagonal tiedown is on the ground.
Openings through the west walls convey instrumentation and utility cables into the tunnel system. These test cells normally handled motors that produced between and pounds thrust direct, and pounds thrust reverse. Maximum thrust capability was 50, 000 pounds. 158 The center bay is an integrated workshop and office space; it is enclosed with a shed roof. An off-center door accesses a workspace that connects Test Stand "E" to the tunnel system on the west facade of the test stand. The tunnel corridor that accesses the tunnel system extends past the west facade. doors flank the tunnel on its north and south facades. The Two adjacent bay to the south, the former X-ray test cell, is now a storage space. Two I-ton hoists run perpendicular to each other through the bay.
One hoist extends past the east facade. A large storage tank is located on the south facade of the test stand; the nozzle extends through the wall into the test cell. A pair of double doors are on the east facade of the south bay, and a door is on the south facade of Test Stand "E." A one-story, 0" x concrete block addition is attached to the west facade of the south bay. It housed a generator and monitor; a door on the south facade of the addition accessed the equipment. Two ~ully enclosed wooden plank blast barriers (native soil and cribbing) are located on the north and south facades of Test Stand "E." The north blast barrier has been extended and encased in a metal sheathing. Test Stand "E" was first used to support NASA's commercial satellite and spaceflight program.
Solid-propellant kick motors, used to place Application Technology Satellites (ATS) in geosynchronous orbit around the earth, were tested at Test Stand 158 Koebig and Koebig. ,, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 99) .'" '~J ~I ~.i.:'i '; "'! 'l~i: : - => -' ~ 1 I .. ".~ : -: ..~ . ~ ". .. 9 1 <> <0 = ~ w . 0 = i 'D .' .'~ '~I i=: , I I1l I .1IQ' o+-' +-' CIl "" d 1'1 NUl Q) i:l .E-o c I tn H 'M 0 G- 1 Ii. 44 I ! i=: C b .; i Cll rl p. '" U 'M Ol Cll ,~ \ , a:l . 0 ~ '" ." i '.' . ' ~ . *' ,.o-,ZI . JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page "E" in the 159 A 10,500-pound solid-propellant motor and solid-propellant nozzles under development for the Space Shuttle program were tested on Test Stand "E" in the late '60 The two test cells were modified to accommodate testing of 48-inch motors for the Space Shuttle program. In later years, the Advanced Solid Rocket Motor (ASRM) was tested at Test Stand "E." The last test firing at Test Stand "E" was conducted in April The storage area on the east side of the complex is JPL Edwards Test Station's other major area with a solid propellant component. The storage sheds are physically separated from each other, a standard safety precaution for the storage of hazardous material. Safety concerns are manifest in the cultural landscape by the extensive storage complex.
The isolated sheds are located approximately 150 feet apart from each other on the east side of the complex, away from all permanently occupied buildings. The native vegetation was scraped away from each of the building locations to help decrease the spread of fire, if an explosion did occur. Ten one-story, open, corrugated metal storage sheds contained solid fuels, solid and liquid oxidizers, and flammable waste. The open storage sheds are partially enclosed on two or three sides. The sheds were primarily two sizes--a small x shed and a larger x shed. Three closed one-story, corrugated metal storage sheds are present as well; however, Buildings 4250/E-5l and 425l/E-52 were originally built as identically-sized 12' -7" x 40' -6" docks for sol id fuel and oxidizer.
They were later converted into storage areas; the second shed at Building 4250/E-5l was built in The roll-up doors were built in as well. The sheds each rest on a poured-in-place concrete foundation, and have steel I-beam frames bolted to concrete foundations. A plumbed emergency shower and eyewash station is present at each building. Concrete hazardous waste retention basins for collecting hazardous materials were constructed at each of these buildings in In addition to supporting the solid propellant research, the storage area also supported the liquid propulsion research. Research work on solid and liquid rockets began to decline in the and as funding cutbacks affected American 159 Gibbons and Tibbitts, 2.
160 National Aeronautics and Space Administration and Jet propulsion Laboratory, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page space programs. However, JPL Edwards Facility staff has been involved in many JPL programs such as Galileo and Magellan interplanetary spacecraft flight projects, which included flight support at Cape Kennedy, Florida. Galileo, a Jupiter orbiter and probe, was envisioned in the late1970s as a follow-up project to Voyager, called JOP (Jupiter Orbiter Probe) Galileo suffered from delays throughout the as it fell victim to Space Shuttle delays, concerns over budgets, and space-borne launch systems. 162 Galileo was finally launched from the Space Shuttle Atlantis on 18 October using the IUS (Inertial Upper Stage) booster.
It is scheduled to encounter Jupiter in December It is flying a complex trajectory called VEEGA Galileo performed of Venus and Earth in before it commenced the direct leg of its trajectory to Jupiter. When Galileo reaches Jupiter in December it will release an atmospheric probe into the Jovian atmosphere, which "will measure the atmosphere's composition and perform other scientific measurements as it descends through Jupiter's thick cloud layers The orbiter will study four of Jupiter's moons, concentrating on 10, monitor Jupiter's atmosphere and magnetosphere and study the radiation belts surrounding the planet.
Galileo observed the comet Shoemaker-Levy 9, which collided with Jupiter in July 164 Magellan, a venutian synthetic aperture radar mappin~ mission, was also originally conceived in the mid 16 Synthetic aperture radar is an airborne electronic technique using a timed pulse signal, which allows the antenna to perform as if it were much bigger than it is. Synthetic aperture radar produces an enhanced, detailed radar image, excellent for cartographic purposes. It was delayed throughout the early because of Space Shuttle and budgetary problems. Magellan was finally launched from the Space Shuttle Atlantis in May Magellan reached orbit in and mapped 99 percent of Venus's surface, including volcanoes, lava plains, highland plateaus and 161 Murray, 162 Murray.
163 Neal et ai, Neal et ai, 164 165 Murray, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page impact craters. 166 Solid-propellant testing has occurred within the last fifteen years, but not in support of specific projects and programs, with the exception of the solid-propellant testing and manufacturing undertaken for Phillips Laboratory, Edwards AFB, California. JPL Edwards Facility has attracted research and development projects on non-propulsion oriented technologies in order to supplement its income, including a Remotely Controlled Tank Target Vehicle for the Army, and Simulation of Area Weapons Effects (SAWE) system for training exercises.
The runways at Edwards AFB hosted evaluation tests for Electric Powered Vehicles and Hybrid vehicles for the Department of Energy, and in the the DOE's Solar Thermal Program established a Parabolic Dish Test Site at the Edwards Facility to develop ways of generating electricity from solar energy.167 The JPL Edwards Test Station is a unique rocket engine testing facility. Not only is it one of the oldest such facilities in the country, but its cultural landscape exemplifies important trends in the history of the Space Age. The Nation's earliest successful guided missiles were tested at the JPL Edwards Test Station. Each of the deep space probes and landers JPL launched before had its propulsion subsystems qualified at the JPL Edwards Test Station.
A unique landscape with associated architecture and engineering evolved to meet the demands of the dangerous and exotic solid and liquid propellant rocket engines used in these spacecraft and rockets. The JPL has led the United States in missile and deep space technology since WWII, and was the Nation's prime builder and developer of missiles and unmanned spacecraft into the The JPL Edwards Facility's decline mirrors that of the deep space program as it slowed down and was eclipsed by the reusable Space Shuttle in the early However, the JPL Edwards Facility remains as a historic resource whose industrial cultural landscape displays the extraordinary lengths to which people went in order to achieve spaceflight.
Because of the significance of the installation to the history of space exploration, the JPL Edwards Facility potentially meets eligibility criteria for listing on the National Register of Historic Places as a National Register Historic District. On 1 October the Edwards Facility will be transferred to the Air Force Flight Test Center at Edwards AFB, and closure plans call for the demolition of 13 structures, including Test Stands "A," liB," lie, and liD. II The Air Force's II Space Surveillance Squadron, which monitors floating debris in near-earth orbit, is scheduled to occupy former JPL 166 Neal et ai, 167 Gibbons and Tibbitts, 3. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page administrative buildings, and the solid propellant line will be transformed into storage space for Base Civil Engineering. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page JPL Glossary Ablation-Type Nose Cone: A nose cone designed to reduce heat transfer to the internal structure; it wears away during descent and transfers the heat. Ballistic Missile: A missile which does not rely upon aerodynamic surfaces to produce lift and consequently follows a ballistic trajectory when thrust is terminated. Excitable: The ability of an atom or molecule to be raised to a higher energy level. Fairing: An auxiliary member or structure whose primary function is to reduce drag where it is fitted to the rocket.
Film-cooled: The cooling of a body or surface, such as the inner surface of a rocket combustion chamber, by maintaining a thin fluid layer over the area. An interplanetary mission in which the spacecraft passes close to a planet, but does not impact it or goes into orbit around it. Frangible: Designed to be easily broken or fractured in a predetermined area. Fuel: A substance used to produce heat by chemical reaction. Guided Missile: Any missile capable of guidance or direction after having been launched. Hydrobomb: A warhead or bomb detonated underwater where the destructive force is a pressure wave greater than the resulting explosion. Hypergolic: A family of rocket propellants that ignite spontaneously when mixed together.
Launch Window: The postulated opening in time or space through which a spacecraft must be launched in order to rendezvous at the desired time or place. Liquid Propellant: A rocket propellant in liquid form. Monopropellant: A rocket propellant consisting of a single substance, especially a liquid, capable of producing thrust without the addition of a second substance. Oxidizer: A substance, not necessarily containing oxygen, supports the combustion of a fuel or propellant. that JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Phase-lock loop tracking system: A tracking or homing system employed on a rocket or missile that acquires its target by comparing the difference between the two signals.
Ramjet: A engine type with no internal mechanical components consisting of a specially shaped tube open at both ends. Regenerative-cooled: The cooling of a rocket engine combustion chamber and/or nozzle by circulation the fuel or oxidizer, or both, around the parts to be cooled prior to combustion in the engine. Solid Propellant: A rocket propellant in solid form; usually containing both the fuel and oxidizer combined or mixed, and formed into a monolithic grain. Sounding Rocket: A rocket that carries scientific equipment for making observations of or from the upper atmosphere. Specific Impulse: Equivalent to the effective exhaust velocity divided by the gravitational acceleration.
Star-shaped solid propellant charge: A hollow rocket propellant charge; with the cross section of the hole having a multipointed shape. Thrust: The pushing or pulling force developed by a rocket engine. Jet Vanes: A fixed or movable surface used in the jetstream of a rocket for stability control, where external aerodynamic controls are ineffective. Wasserfall: A World War II German liquid propellant surface-to- air guided missile that used a cascading water cooling system. Water-cooled: Cooling the engine by water. JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page Acronym List AAF Army Air Force ABMA Army Ballistic Missile Agency ACE Army Corps of Engineers AFB Air Force Base AFFTC/HO Air Force Flight Test Center/History Office AFFTC/EM Air Force Flight Test Center/Environmental Management ASRM Advanced Solid Rocket Motor BHPO Base Historic Preservation Office BTU British Thermal Unit Caltech California Institute of Technology esc Computer Sciences Corporation DSN Deep Space Network ETS Edwards Test Station GALCIT Guggenheim Aeronautical Laboratory/California Institute of Technology GeMS Gas Chromatograph/Mass Spectrometer GE General Electric GPM Gallons per minute HABS Historic American Buildings Survey HAER Historic American Engineering Record IUS Inertial Upper Stage JATO Jet-Assisted-Takeoff JOP Jupiter Orbiter Probe JPL Jet Propulsion Laboratory MJS Mariner/Jupiter/Saturn JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page MMH Mono Methyl Hydrazine NACA National Advisory Committee on Aeronautics NASA National Aeronautics and Space Administration NHL National Historic Landmark National Register of Historic Places RRL Naval Research Laboratory NASA Standard Igniter ORDCl:T Ordnance Department/California Institute of Technology ORR Office of Naval Research Pounds Per Square Inch RCRA Resource Conservation and Recovery Act RFNA Red Fuming Nitric Acid RTV Reentry Test Vehicle SAWE Simulation of Area Weapons Effects SHPO State Historic Preservation Office UDMH Unsymmetrical Dimethyl Hydrazine USGS United States Geological Survey WAC Without Altitude Control or "Women's Army Corp" WFNA White Fuming Nitric Acid World War II VEEGA VfR Verein fur Raumschiffahrt ("Society for Space Travel") JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-l63 (Page Chemical Names and Formulas Aniline: C (also called aminobenzene or phenylamine) Boron oxyfluoride: BOF Boron trichloride: Boron trifluoride: BF, Calcium fluoride: caF, Calcium hydroxide: Ca(OH), Calcium hypochlorite: Ca(ClO), (commercially known as Perchloron) Calcium tetraborate: CaB.O, Carbon dioxide: CO, Chlorine trifluoride: Chlorine pentafluoride: ClF s Decaborane: BlO H14 Diborane: B,H 6 (also known as boron hydride) Dichlorodifluoromethane: (commercially known as Freon) Dihydrotetraborane: B.H 10 Ethyl aniline: C6 (several isomers exist) Fluorine: F, FLOX: cryogenic mixture of liquid oxygen (LO, or LOX) and liquid fluorine Gaseous hydrogen: GH, Gaseous nitrogen: GN, Helium: He Hexaborane: B6 HlO Hydrazine: Hydrofluoric acid: HF JPL EDWARDS FACILITY Edwards Test Station) HAER No, CA-163 (page Hydrogen: H, Hydrogen peroxide: H,O, Lime: CaO Liquid fluorine: LF, Liquid nitrogen: LN, LOX: liquid oxygen: La, Lithium hydride: LiH Mono methyl hydrazine, or CH 3 Ni trogen: N, Ni trogen dioxide: NO, Ni trogen tetroxide: N,O.
Oxygen difluoride: OF, Pentaborane: Sodium borate: Na,B.O, Sodium fluoride: NaF Sodium hydroxide: NaOH Unsymmetrical dimethyl hydrazine, or UDMH: ,N' NH, Water: H2 0 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page PROJECT INFORMAT:ION This HAER report had its genesis in a Phase II cultural resource evaluation of the Jet Propulsion Laboratory Edwards Facility conducted by Scott M. Hudlow, Architectural Historian, Environmental Engineering Department, Applied Technology Division, Computer Sciences Corporation, Edwards Air Force Base, Edwards, California.
The Phase I I study determined that the Edwards Facility was eligible as a National Register of Historic Places historic district, and that the JPL/Air Force Flight Test Center closure plans resulted in adverse effects which merited mitigatory HABS/HAER documentation under Sections 106 and 110 of the National Historic Preservation Act. The historical background and sources from Mr. Hudlow's work were adapted by Richard K. Anderson, Jr. to meet the HAER report format and HABS/HAER standards as required by the Phase III cultural resource documentation project conducted by Mr. Hudlow. Mr.
Anderson also included in the report numerous technical and historical observations derived from reviews of historic engineering drawings, JPL photographic records, site visits to test stands, and telephone and taped interviews with JPL test engineers. Photocopied engineering drawings from JPL Edwards engineering office, and copies of test stand schematics used in preparing the HAER report and drawings have been filed with the HAER project field records, along with several dozen field photographs taken by Mr. Hudlow in Neither time nor funding was available to study the impact of individual engineers and personalities on either the design and evolution of the JPL Edwards Facility or its individual test stands.
Nor could these individuals' contributions to the design and success of spacecraft series be evaluated. The financial aspects of JPL Edwards operations, such as the costs and schedules of any or all specific series of tests (equipment, propellants, etc.) were outside the scope of this report. Neither time or opportunity to review the design and results of individual tests for what they might reveal about the evolution of the test stands was available. The history of specific rocket engine designs tested at JPL Edwards was beyond the scope of this report. All of these topics deserve further research given the uniqueness of the site and its historic mission. In addition to the HAER report, Mr. Anderson prepared four HAER measured drawings, and collaborated with Mr.
Hudlow in selecting sites for HAER photographic documentation as well as photocopies of historical photographs and drawings for inclusion in the HAER project record. Contemporary large format photography was conducted by Brian Grogan, Yosemite photographics, Inc., Yosemite, California. Historical JPL JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Ill) negatives were photocopied by Bob Schlosser of the Huntington Library, San Marino, California, with the invaluable help of David Deats at the JPL Photographic Laboratory in Pasadena, California. Some of the HAER record photographs are photocopies of field photography made by Mr. Hudlow and are included with his permission.
The HAER report, measured drawings and large format photography were prepared under Computer Sciences Corporation purchase order no. 14 December Richard K. Anderson, vendor. Hudlow and Anderson appreciate the numerous hours of assistance given by JPL employees William C. Tibbitts Edwards Facility Manager), John Richard ("Dick") Bonner Facility Test Engineer), David Quarles Facility Test Engineer), John Bluth Archivist, Pasadena) and others in pointing out files, investigating facilities, answering questions and reviewing the HAER documentation at various stages of its preparation.
primary and Secondary Research Primary and secondary research for the Phase II architectural evaluation was conducted between July and November Primary records were reviewed at the National Archives in Laguna Niguel, California. Historic construction drawings and site plans were located at this National Archives facility. The Air Force Flight Test Center History Office (AFFTC/HO) had little documentation pertaining to the JPL Edwards Facility. Because JPL is a non-Air Force tenant organization, its historic records have not been systematically retained by the AFFTC/HO. The AFFTC/HO did, however, contain some useful written documents regarding including historic Army reports.
The JPL has its own archive in Pasadena, California, where the JPL Edwards Facility collections will be deposited after closure. Primary records in the custody of the JPL Edwards Facility were consulted. The JPL Edwards Facility real estate files recorded information concerning the construction of each of the standing buildings, and the JPL Edwards Facility "as-built" drawings document the standing structures and their cultural landscape. Selected files were consulted for test stand process schematics and relevant operator's manuals. The base library proved useful for locating secondary sources on JPL and the space program. Off-base libraries and repositories were contacted and/or visited to complete the project.
Beale Memorial Library (the main .branch of the Kern County Library) in Bakersfield, California, was contacted and visited, but little relevant JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page information was obtained. The Walter W. Stiern Library at California State university, Bakersfield, was also consulted. Secondary sources on JPL and the space program were located at Beale and Stiern libraries. Finally, the JPL archive in Pasadena, California was consulted. The JPL archive contains historic photographs, articles, historic reports, and newspaper. The JPL archive housed the most quintessential historic information germane to the JPL Edwards Facility. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (page
Illustration Sources
Fig. 1 Compiled from two engineering drawings: bottom half based on California Institute of Technology, Jet propulsion Laboratory, Plant Engineering, "Edwards Test Station plumbing Distribution," drawing no. EPDIl2-1, 4 March top half based on California Institute of Technology, Jet propulsion Laboratory, Plant Engineering, "Exhaust Scrubber Facility Location & Vicinity Map", drawing no. El8/15, no date (ca. Fig. 2 Test Stand "A" process schematic from the "A" Stand files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, California. Fig.
3 Tunnel Section from Koebig & Koebig, Inc., Engineering, Architecture, planning, December Master Plan for Edwards Test Station, National Aeronautics and Space Administration, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California. Report on file, JPL Edwards Facility, Edwards AFB, California. Figs. 4-6 From schematics in the files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, California. Fig. 7 From cover sheet of original "D" Stand drawings, titled "Request for Approval for Test Stand E-24 and Set Up Shop E-23 at JPL-Edwards Test Station, Muroc, Calif.", drawing no. E-24/1-0, 29 January Figs.
From schematics in the files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, California. Fig. 13 From JPL negative no. 26 July Draftsman undetermined. Figs. Schematics from the files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, California. Fig. 18 From typescript operator's manual by Frank C. Brown & Company, Inc. "Toxic Exhaust Scrubber Facility." JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Revised December p. 6. Found in "C" Stand files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, Cal if ornia. Fig.
19 Schematic from the files of David Quarles and John Richard Bonner, JPL test engineers, JPL Edwards Facility, Edwards AFB, California. Fig. 2 Plan of Test Stand "E" from California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering, "Test Stand Building E-60," drawing no. E- 10 August NOTE: Larger copies of the line illustrations are contained in project field notes transmitted with project history, photographs and measured drawings. Copies of other schematics and engineering drawings of interest were retained in the field notes as well. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page BIBLIOGRAPHY
Primary
Operated by the California Institute of Technology, the Jet Propulsion Laboratory Edwards Facility was the United States' first university-sponsored research and testing facility for the development of liquid-fueled rocket engines and components. It became an important national test facility. Solid- propellant rocket motors were built and tested at the JPL Edwards Test Station, including Space Shuttle nozzles and motors, Syncom 1, 2, and 3 motors, Application Technology Satellites solid rocket motors, and the solid rocket motors for the Surveyor and voyager lunar and interplanetary probes . Historians: Primary: JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Scott M.
Hudlow, Architectural Historian, Computer Sciences Corporation, Edwards Air Force Base, California Secondary: Richard K. Anderson, Jr. Columbia, South Carolina. July 1995-December . TABLE OF CONTENTS JPL ~
Dwards Facility
Edwards Test Station) HAER No. CA-163 (page Historical Background and Context 125 GALCIT and solid Propulsion . 125 Post-War Contributions to Solid-propellant Technology 129 Solid Propellant Testing at the JPL Edwards Test Station 137 Site Characteristics 144 Cultural Landscape and Architectural Evaluation 145 Building Layout and Air Force Safety Regulations 152 Building the Solid Propellant Processing Line 152 Solid Propellant Preparation Parameters 155 Propellant Ingredient Storage 158 Oxidizer Weighing and Storage .' 161 Oxidizer Grinding 162 Drying and Blending of Oxidizers 169 Fuel Preparation . . . 176 Motor Casings and Liners 181 Curing . .
195 Preparation 198 Conditioning 206 Sterilization 212 Physical Properties Tests 214 Non-combustion Tests 216 Viscosity Tests 216 Tensile Tests 218 Peel Tests 218 Specific Gravity Tests JPL ~DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 219 Combustion Tests . 221 Burn Rate Tests 221 X-Ray 223 Motor Assembly 226 Test Stand vibrator 231 Test Stand "E" 235 Waste Disposal and Clean-Up 236 Facility Administration 237 Chemical Names and Formulas 240 Project Information 242 Figure Sources 245 Bibliography 251 .. JPL ~DWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page Historical Background and Context The Jet Propulsion Laboratory dates from It originated as part of the applied mechanics program at the Guggenheim Aeronautical Laboratory/California Institute of Technology (GALCIT). Six student scientists, Hsue Shen Tsien, Apollo M. O. Smith, John W. Parsons, Edward S. Forman, Weld Arnold, and Frank W. Malina, led by Hungarian emigre Theodore von Karman, conducted the first static tests of rocket engines in in the Arroyo Seco, a dry riverbed, located at the western edge of the San Gabriel Mountains in Pasadena, California. The Arroyo Seco was chosen for its relative isolation from urban development, lack of foliage, and proximity to the California Institute of Technology (Caltech) campus in Pasadena.
' GALCIT was an early, amateurish rocket project that conducted both liquid-propellant and solid-propellant research. 2 Caltech has since been recognized as the first university in the United States to sponsor formal rocket research. GALCXT and Solid Propulsion r-, The GALCIT group went through rough years in and as the crisis in Europe deepened. However, in the spring of the U.S. military's nascent desire to harness the potential power of rocketry engendered a financial commitment from the National Academy of Sciences Committee on Air Corps Research to fund the GALCIT rocket group. John W. Parsons, an expert in explosive chemicals, particularly harbored an interest in solid propellants.' 1 Daniel, Mann, Johnson, and Mendenhall.
Master Facilities Plan Report on file at JPL Edwards Facility, Edwards AFB, California, unpaginated; Koppes, Clayton R. JPL and the American Space Program: A History of the Jet Propulsion Laboratory. New Haven, Connecticut: Yale University Press, 2 Koppes, , Solid propellants are a combination of fuel and oxidizer, brought together and mixed into a single solid mass called the "grain." The fuel is usually prepared in a liquid state, and the oxidizer is prepared in a solid state, usually as a powder, and later mixed with the fuel. When the "grain" is conditioned; it solidifies to form the propellant. The two constituents together provide better burn characteristics than ei ther demonstrated alone. An alternative solid propellant is a double-base type solid propellant.
In this combination, each of the two primary \ JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Parsons " ... possessed an encyclopedic command of explosives and similar chemicals," and had worked occasionally for powder companies before his association with GALCIT. Awash with the National Academy of Sciences money, GALCIT and Parsons experimented with diverse powder combinations trying to create a safe solid-propellant charge. s The U.S. Army provided the immediate impetus for solid-propellant research due to its preference for solid propellants because of their ease of handling and its interest in rocket-assisted takeoff for propeller-driven aircraft. Yet, solids research was especially difficult for GALCIT scientists.
Clayton Koppes, historian, relates that: To be effective in helping boost propeller-driven planes at takeoff, rockets would have to burn for perhaps 10 to 20 seconds. But no solid-propellant engine then known burned for more than about 3 seconds. It couldn't be done, most of the experts advised. The conventional wisdom held that once the propellant was ignited, pressure would build rapidly in the chamber and cause the engine to explode. Repeated explosions with almost every version Parsons tried seemed to prove the experts right. He tried innumerable combinations of black powder in several configurations, most designed to burn slowly from one end, like a cigarette. The experimenters clung to the hope that the difficulties were mechanical, not fundamental.
They surmised that somehow the walls of the powder charge were ignited or that the charge cracked when the pressure in the chamber rose. But by spring the explosions and expert advice had driven the group to the point of giving up on solids. 6 Although experts believed that solid propellants were not practicable, the GALCIT group inched forward. First, they demonstrated that long-duration, end-burning, solid-propellant rocket motors were theoretically possible. Second, in the summer of GALCIT developed a small two-pound amidic, end-burning, black powder solid-propellant charge, later designated GALCIT 27. It burned modestly for 12 seconds and produced 28 pounds of constituents could, theoretically, burn on its own accord in a vacuum.
The double-base type solid propellant contained a mixture which has the properties of both fuel and oxidizer . Koppes, 3. 5 Koppes, 10. 6 Koppes. 10. JPL .
Edwards Facility
Edwards Test Station) HAER No. CA-163 (Page thrust. The solid-propellant charge was compressed into a cylinder 10 inches long and inches in diameter with a blotting-paper liner in 22 increments at a pressure of 18 tons. 7 GALCIT 27 was the basis for the first solid-propellant jet-assisted takeoff (JATO) rocket. The GALCIT group first tested the solid-propellant JATO rocket at March Field in Riverside, California in August The JATO rockets were tested at Muroc Army Air Base, now Edwards Air Force Base (AFB) beginning in First, static testing was conducted, second the rockets were ignited after the plane was in flight, and last, the JATO rockets were used to assist takeoff. The rockets were tested on a propeller-driven Ercoupe, a lightweight, low-wing monoplane.
Three bottle-shaped solid-propellant motors were inserted under each wing. Lt. Homer Boushey, on 12 August soared into the air using rocket power for the first time in American history. Koppes states that "The JATOs cut the distance required for takeoff nearly in half, from 580 feet to 300 feet; the time required to become airborne was reduced almost as much, from seconds to 7.5 seconds, or percent. The plane's structure suffered no ill effects; in (' fact, Boushey reported, " ... it was easier to handle the plane with the rocket thrust. ,,8 Parsons and the rest of the GALCIT group soon discerned a major problem- JATO rockets were not stable. The GALCIT 27 JATO rockets deteriorated quickly; long-term storage of JATO rockets in combat conditions was unfeasible.
The GALCIT group searched for a solution: they modified the JATO design, tested different types of blotting paper, and investigated diverse chemicals as propellants. After the United States entered World War II (WWII) in December the U.S. Navy desired a JATO rocket that would provide 200 pounds of thrust for 8 seconds. The U.S. Navy contracted with GALCIT to provide this product.' Parsons and the GALCIT researchers were desperate for a solution to the long- term stability problem. Parsons decided to eschew the black powder/saltpeter solid propellant combination altogether. He instead tried paving asphalt as a fuel and potassium perchlorate as an oxidizer. This solid-propellant combination, designated GALCIT 53, was immediately successful. By refinements led to GALCIT 7 Koppes, 1I.
8 Koppes, (' , Koppes, 12. JPL .EDWARDS FACILITY Edwards Test Station) HAER NO. CA-163 (Page which when burned at a chamber pressure of pounds psi (per square inch), had an Isp (specific impulse) of an exhaust velocity approximating feet per second, and could be stored indefinitely within wide temperature extremes (between -9 F and 0 F). After this fundamental breakthrough in solid-propellant research, the U.S. Navy was able to use JATO rockets extensively during the last two years of WWII for carrier-based operations in the Pacific theatre." O The GALCIT rocket project made significant and important theoretical and practical advancements in solid-propellant rocket technology.
GALCIT was the first group to demonstrate the feasibility of constant pressure, long-duration solid-propellant rockets using the GALCIT 53 asphalt-based propellants. Aerojet Engineering Corporation, a JPL spin-off company, was created to further develop and market JATO motors during WWII. Theodore von Karman, Andrew Haley (Karman's attorney), Parsons, Malina, Forman, and Martin Summerfield, a JPL liquid propellant researcher, provided the capital and assigned all patents to Aerojet. GALCIT and Aerojet had an interlocking relationship as employees moved between the two organizations. Parsons left GALCIT to work for Aerojet permanently; however, Karman and Malina instead worked as Aerojet consultants.
Aerojet also had many of its applications tested at the GALCIT test station in the Arroyo Seco. 11 GALCIT began formally calling itself the Jet Propulsion Laboratory in 2 The name JPL was chosen carefully and consciously. David Baker, a science writer, states: ... that while most of the work embraced by these assignments was centered on rocket propulsion, the word 'jet' was applied in each and every case when an organization was set up to conduct theoretical and practical tests. The popular interpretation of the word 'rocket' had too flippant a connotation to engender the degree of respectability demanded by the work!13 10 Koppes, 11 Daniel, Mann, Johnson, and Mendenhall; Koppes, 12 Koppes, 20. 13 Baker, David. The Rocke t : The History and Development of Rocket & Missile Technology.
New York, New York: Crown Publishers, Inc., .
Jpl.edwards Facility
Edwards Test Station) HAER No. CA-163 \Page GALCIT's new name, enabled an additional $3 million in funding, and the staff tripled to more than 250 people." Post-War Contributions to Solid-Propellant Technology Solid-propulsion research at JPL continued after WWII. Sergeant, Loki, Thunderbird, and the RTV (Reentry Test Vehicle) were important late and military and space science solid-propulsion projects. The GALCIT/JPL solid-propellant achievements are a distinct American and JPL contribution to the history of rocketry that led directly to the development of significant large Cold War solid-propellant missiles such as Polaris, Poseidon, and Minuteman at various other laboratories .15 The tremendous technological advances generated both positive and negative results.
JPL was able to advance rocketry and lay the foundation for the unmanned space program; however, JPL began to have problems with its Arroyo Seco location that jeopardized the testing operation. By the mid population growth in the surrounding communities of Pasadena, Altadena, La Canada, and Flintridge began to limit the facility's ability to conduct large-scale rocket engine tests. 16 At WWII's conclusion, the area was heavily settled with upper middle-class residents, some of whom overlooked the Arroyo Seco. The area's residents n objected to the noise of static tests, and to the laboratory's unsightliness. For example, the Corporal E liquid rocket engine produced 120 decibels of noise at an altitude of 200 feet.
1 JPL scientists and engineers were forced to find an isolated location where it was possible to conduct noisy and hazardous tests. Daniel, Mann, Johnson, and Mendenhall. 15 Koppes, 17. 16 Gibbons, John and William C. Tibbitts. Edwards Facili ty Historic Overview". TYpescript on file at AFFTC/EM, Edwards AFB, California, 17 Koppes, 48. 18 Bluth, John (Archivist, Jet Propulsion Laboratory, Pasadena, California). Telephone conversations with Scott M. Hudlow, January -- - - - - - - - - - - - - - - - - - - - - - - ;e.,,~ e'he :,,_e e" e~e~, JPL ~DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page JPL had tested JATO rockets at Muroc and was familiar with the Base.
Consequently, the Muroc Flight Test Base was perceived as a perfect location when JPL conducted a search in for a nearby, yet isolated, site for its rocket engine testing facility. The new JPL facility was initially designated the ORDCIT (Ordnance Department, California Institute of Technology) Test Station; it was renamed the JPL Edwards Test Station in Although the liquid-propellant engine testing was moved to the high desert, the solid-propellant motor testing remained in Pasadena until when it was moved to the JPL Edwards Test Station. The ORDCIT project, which dated to WWII, was designed to develop a series of rockets and associated launching hardware.
The ORDCIT project focused on liquid propulsion technology; however, JPL was interested in continuing to improve solid propellants after it had discovered the asphalt-based solids. This was the beginning of the private, Corporal, and Sergeant rockets JPL developed for the Army. Private and Corporal were liquid rockets;" Sergeant was a solid-propellant rocket, and the nation'S first solid-propellant ballistic missile. In the mid the prevailing scholarly opinion was that solid propellants could not equal the potential of liquid propellants for large rockets. G. Edward Penray, a founder of the American Rocket Society, stated in that solids would " ... never give the power and sustained performance needed for high-altitude sounding rockets ... or long-range military or trajectory rockets.
Solid propellants had power and sustainability problems that were difficult to overcome. Solid propellants also needed to burn slowly, consistently, evenly, at a relatively low initial temperature, use an internal-burning grain, and be operational within wide ambient and controlled temperature ranges. These characteristics are inconsistent with the asphalt-based solid JATO motors, so JPL engineers and scientists began searching for a solution. They wanted to design a larger solid-propellant rocket. In late a JPL engineer established that a rubberlike polysulfide developed by the Thiokol Corporation possessed many of the best characteristics of the asphalt-based solid propellants the JPL was using in its JATO without their weaknesses.
However, the rubberlike polysulfide developed a " Please consult the original HAER report for a lengthy discussion of the Corporal and Private programs. 20 Koppes, 36. JPL ~DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page burning-rate problem and formed a cone inside the propellant charge that changed the rate at which the propellant burned. As JPL attempted to solve this practical problem, Army Ordnance contracted with JPL to develop a small six-inch solid booster rocket known as Thunderbird. The Thunderbird was used as a test vehicle to solve the burning-rate problem, and to ascertain whether the polysulfide could withstand the exaggerated acceleration pressures associated with launching.
An internal-burning propellant charge with a star-shaped central hole through the propellant grain was developed by English researchers and scientists at the Allegheny Ballistics Laboratory in West Virginia. JPL appropriated the internal-burning star to ascertain whether it could solve the burning-rate problem by providing constant thrust. 21 Clayton Koppes relates that: ... JPL researchers learned of the star almost by accident, through an appendix to another report being circulated among military laboratories. For the Thunderbird motor the engineers applied a thin liner to the wall of the combustion chamber, then mounted a ten-point-star-mold core in the center of the chamber.
They poured the polysulfide propellant in the chamber and, when the propellant began to harden, removed the star. The design was simplicity itself. When the Thunderbird motor was ignited, the charge burned slowly from the inside, and the star gradually formed a cylinder. The burning-rate problem was solved, and the polysulfide proved it could withstand the acceleration. 22 The successful Thunderbird tests in early led to ambitious tests on larger solid-propellant motors. Theoretical models demonstrated that solid-propellant motors the size of the WAC (Without Altitude Control) Corporal 12-inch liquid propellant engine could reach an altitude of feet. However, static tests performed on a IS-inch motor caused explosions due to thin steel liner cases.
The unexplained explosions (at the time) lessened enthusiasm for solid-propellant research at the same time JPL was gearing toward the militarization phase of the liquid propellant Corporal rocket program. 23 JPL continued to conduct minor solid-propellant research in 21 Williamson, Mark. Dictionary of Space Technology. Adam Hilger: New York, New York, Koppes, 22 Koppes, 37. 23 Koppes, 37. the early in Pasadena. JPL ~DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Loki, an antiaircraft missile derived from the German's WWII Taifun missile, was the first JPL solid-propellant program to benefit from these new discoveries. Taifun was a small pencil-thin unguided antiaircraft rocket with a diameter of 4 inches and a height of 6 feet.
24 Army Ordnance considered Loki a backup to the Hercules Powder Company's Nike 2s antiaircraft missile in case Nike failed. Loki was an impractical weapon, but an interesting research project. The small rocket measured approximately 6 feet long and 3 inches in diameter and had a package of high explosives strapped on the end. The unguided Loki was launched in supersonic barrages, upward of Mach 6.5 to Mach 7. Nike, however, worked. The Army canceled Loki, to the consternation of JPL engineers. JPL had Loki's solid propellants burning faster than any previous solid-propellant motors ever designed, and had made important advances in aerodynamics and stability, which JPL engineers relinquished when Army Ordnance canceled the project.
One JPL engineer suggested Loki would make an excellent pyrotechnic launching device; it was later utilized as a high-altitude sounding rocket. 26 After Loki, JPL began actively working on the Sergeant missile, which was Corporal's successor. Sergeant was a solid-propellant battlefield ballistic missile, and the u.S. Army's first large solid-propellant missile. It was tested at Pasadena in the late and into the The Sergeant missile emerged as a single-stage, solid-propellant rocket with a 34-foot length and a 30-inch diameter. The forward section was a straight-sided elongated cone that converged to a point; four stabilizing aerodynamic fins were clustered around the base. The Thiokol XM-IOO solid-propellant rocket motor produced tons of thrust; launch weight was approximately tons.
27 Sergeant was the first large ballistic missile to benefit from advancements in solid-propellant technology. Sergeant went into service in It was a mobile system that was transported by air in four sections. Sergeant was the 24 Neufeld, Michael J. The Rocket and the Reich: Peenemiinde and the Coming of the Ballistic Missile Era. New York, New York: The Free Press, 2S Baker, 26 KOppes, 27 Baker, 248 . JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page army's main short-range (between 60 and 190 miles) battlefield missile. The long-distance Pershing rocket, which had an approximate range of miles, complemented the Sergeant missile. The Sergeant missile was capable of hitting both advancing and rear echelon units. As recently as West German and U.S.
Army units operated the Sergeant missile. 2 as an organization, had harbored desires to attempt space flight since the As the progressed JPL was increasingly uncomfortable conducting classified military research for military applications, although it was successful in developing the Corporal and Sergeant missiles. JPL began looking to the stars, and to conducting the space scientific research at the core of the original GALCIT dream. The need for secrecy struck many JPL personnel as distinctly at odds with the goals of higher education exemplified at Cal tech and with their desire to conduct space scientific research. 2 ' JPL ceased military applications after the Sergeant missile's successful development and militarization in ending its association with Army Ordnance.
30 JPL spent the transforming the Corporal E and Sergeant missiles into effective weapons systems for the U.S. Army. However, during the same period they began shifting from guided missile research to instrumented deep space exploration. In first foray into space exploration began modestly. JPL embarked on the development of Orbiter, an artificial earth satellite, in collaboration with the Army Ballistic Missile Agency (ABMA) and the Office of Naval Research (ONR). This project marks the beginning of phased program of instrumented deep space exploration. 31 The Orbiter project was planned to help celebrate the upcoming International Geophysical Year (IGY). This project was competing for the right to build the first American satellite.
The Orbiter satellite proposal was composed of an Army Redstone solid-propellant rocket as a first stage, and downsized Sergeant motors for the second and third stages necessary to place the satellite in orbit around 2. Baker, 2. . Koppes, 30 In the late JPL began conducting classified military research again for the first time since the However, military applications comprise less than 5 percent of overall work. 31 Daniel, Mann, Johnson, and Mendenhall; Koppes, . the Earth. JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page The impressive ABMA/ONR/JPL Orbiter proposal was joined by two additional proposals.
The Orbiter proposal's competition came from the Naval Research Laboratory's Vanguard proposal, and an Air Force proposal, which entailed the use of an Atlas rocket coupled with an Aerobee-HI second stage to achieve earth orbit. President Dwight D. Eisenhower wanted the project to have a non-military focus and desired America's first artificial satellite to be utilized in peaceful and scientific studies .32 Faced with three plans, the Department of Defense organized a special advisory group to review the various proposed satellite programs and make recommendations. Although the advisory group favored both the use of the Air Force's Atlas missile and the ABMA/ONR/JPL proposal, it was concerned about adapting military missiles for satellite deployment.
The advisory group advocated developing a nonmilitary launch vehicle. The NRL granted Vanguard superior electronic technology to transmit scientific data from space to Earth-- the advisory group decided Vanguard .~ had the best chance of placing the most useful satellite into orbit within the IGY This decision led to a controversy over which was the best proposal, Orbiter or Vanguard. The Soviet Union's successful launching of Sputnik on 4 October made the Orbiter-Vanguard debate a moot point. Instead, Sputnik bred a controversy over whether choosing Vanguard was a good decision." meanwhile, found an outlet for its Orbiter project.
The ABMA in the mid was engaged in an interservice rivalry with the Air Force; it was attempting to develop the Jupiter medium-range ballistic missile before the Air Force finished its Thor medium-range ballistic missile .. The Orbiter studies helped the ABMA create the it was designed to test the Jupiter missile's ablation-type nose cone, which was used to counteract the intense heat produced by reentry. The RTV was similar to the Orbiter proposal; the missile needed only a fourth-stage rocket and a payload to launch an artificial satellite. Microlock electronics technology was also adapted to the RTV program. The Microlock electronic technology is a phase-locked loop tracking system, which later became the foundation of the Deep Space 32 McDougall, Wal ter . . ..
The Heavens and the Earth: A Political History of the Space Age. New York, New York: Basic Books, 33 Koppes, JPL.EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Network that tracks deep space vehicles. The Microlock system could send data back to ground control on the missile's heating effects during flight, and its tracking mechanism made possible the nose cone's recovery at the end of the flight. The RTV also incorporated solid-propellant technology in the last stages of the launch vehicle. The first stage was a modified Redstone missile, designated Jupiter C.
The second stage incorporated eleven small solid-propellant Sergeant motors mounted annularly inside a tub; the three motors of the third stage fit inside the second stage, and the fourth-stage motor and payload rested in the center. When each stage fired, the shear pins attaching it to the previous assembly were broken allowing the previous stage to descend to Earth. For greater accuracy, the upper stages were enclosed in a spinning tub powered by two battery-driven electric motors. The tub began spinning at 550 rpm (revolutions per minute) before takeoff; the speed gradually increased to about 750 rpm around 70 seconds into the flight. This procedure eliminated the resonance between the missile's spin and bending frequencies which increased as the first-stage propellants were depleted.
The spinning tub imposed severe vibration and centrifugal force on the second stage. Throughout the design of the upper stages, highly accurate positioning and balance was necessary to curb the vibration and deflection concerns. The Army fired the first RTV at Cape Canaveral, Florida on 20 September it attained an altitude of 682 miles and had a range of miles, both new records for American missiles. The test objectives were met: the motor demonstrated the desired power, the aerodynamic design worked satisfactorily, and the Microlock system performed close to theory. The ABMA was not allowed to launch a satellite, so the fourth stage was filled with sandbags.
If the RTV had contained a small sergeant motor for use as an apogee kick motor in a true last stage, it would have become the world's first orbiting artificial satellite over a year before Sputnik. '4 After the Soviets launched Sputnik, the diverse American groups scrambled to respond to the immediate loss of prestige. The American public perceived that the U.S. was falling behind the Soviet Union.'s Three weeks after Sputnik, Orbiter was given a renewed opportunity, but not before the Vanguard team had '4 Koppes, 80. '5 McDougall, JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page its Orbiter's name was changed to EXplorer 1; it continued as a backup to Vanguard.
Before Vanguard got its chance, the Soviets, on 3 November placed Sputnik 2 in orbit, which included Laika, the space dog. project Vanguard was plagued with technical problems. The Vanguard launch vehicle, which had not been perfected prior to this undertaking, frequently exploded. Vanguard was launched from Cape Canaveral, Florida on 6 December Vanguard never left the pad; instead, it sat and burned uncontrollably on national television. Meanwhile on 8 November JPL had been authorized to proceed with Explorer launch preparations. The Explorer satellite was launched from Cape Canaveral, Florida on 29 January boosted by the ABMA's Redstone medium-range rocket. The successful Explorer 1 was America's first artificial satellite.
While Explorer 2 did not achieve orbit because of a structural failure, Explorer 3 was the second American satellite in orbit on 26 March EXplorer 3 discovered the Van Allen radiation belts which circle the Earth. JPL was now firmly established as the nation's leading space organization, as well as, a leading missile development agency. In December the National Aeronautics and Space Administration (NASA) was created.
It was formed from the National Advisory Committee for Aeronautics; President Eisenhower gave NASA the right to absorb any space-related agency it wanted, such as the which had developed the failed Vanguard rocket and satellite, the ABMA, which became Marshall Space Flight Center in Huntsville, Alabama, and including the test station at Edwards AFB.' JPL was reluctant initially to join the new space agency. JPL felt it had the opportunity to become the lead contractor for the new space agency, a role which NASA did not endorse. By NASA's primary goal was to land a manned spacecraft on the Moon. NASA was specifically pushing project Mercury, the first manned space program.
However, JPL decision makers decided to develop unmanned robotic spacecraft rather than manned spacecraft, since JPL would have the primary role in the unmanned program, . rather than join the other NASA installations involved " Butowsky, Harry A. Landmark Study. Washington, Man-in-Space National National Park Historic Service, (' Department of Interior, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page in the manned spacecraft program. 37 The Edwards Test Station (ETS) played an important role in unmanned space exploration program, which included not only deep space vehicles, but also earth orbiting satellites.
Solid propellant Testing at the JPL Edwards Test Station Solid propellant testing remained in Pasadena until when the operation was moved to the JPL Edwards Test Station. The JPL Edwards test station had been in operation since testing liquid-propellant engines on its four test stands. The ETS solid-propellant processing line was NASA's sole in-house solid-propellant facility. The solid-propellant processing line was removed to Edwards for many of the same reasons the liquid propellant testing was transferred to the desert in The local population continued to grow and JPL grew as it created a modern science laboratory complex in the Arroyo Seco as a result of the unmanned space program. Solid-propellant testing was a dangerous and hazardous operation.
It needed space, which was no longer available in the Arroyo Seco, to conduct tests in a safe manner. Another major factor in moving the solid-propellant testing to the JPL Edwards Test Station was to buttress the station's mission. Gilbert Bell, the ETS engineer-in-charge, attempted in the late to move the station and dramatically change its testing profile to accommodate test stands for motors and engines upward of pounds of thrust. This proposal would have entailed moving the station to a different location to provide the necessary space for colossal new test stands. JPL considered locations at Fort Irwin, Camp Cooke (now Vandenberg AFB), Camp Pendelton, and Edwards AFB, east of Phillips Laboratory.
Several of these locations were approved; the test station was gearing to move to Camp Cooke in when the plans were canceled for unknown reasons. The JPL test station stayed at its present location. Gilbert Bell, the architect of these expansion plans, died three years later in a fatal train and car collision, which squelched the call for new significant growth at ETS. The transfer of the solid-propellant line appears not only to have answered the spatial needs of the lab in Pasadena, but also seems to have satisfied the ETS's desire to grow. 3 The advent of NASA and.JPL's acquiescence to NASA probably were factors in the 37 Newell, Homer E. Beyond the Atmosphere: Early Years of Space Science. Washington, National Aeronautics and Space Administration, Koppes, ~ 3.
I Bluth, personal communication. JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page decision to retard the JPL Edwards Test Station's growth. Although the JPL Edwards Test Station did not expand in the manner the JPL Edwards Test Station wanted, it did increase enormously in when the solid-propellant line was built at ETS. A Chemical Propulsion Information Agency survey of solid- propellant facilities, including the facilities which conducted small arms and hand-held weapons research, noted in that 22 different organizations conducted solid propellant research at 35 operational locations across the country, particularly California and Maryland. Many of these facilities were quite small, and limited in scope, testing only extremely small motors.
3 The JPL Edwards Test Station solid-propellant line was a medium-sized processing line that specialized in satellite motors and solid rocket motors for JPL deep space probes. Two major JPL satellite projects were Syncom (Synchronous Communications Satellite)40 and ATS (Application Technology Satellite) satellites. Surveyor and Voyager solid rocket motors were also developed at the JPL Edwards Test Station. 4l Syncom was an important joint NASA and Department of Defense communications satellite program developed in the early The Hughes Aircraft Company built the Syncom satellites and JPL designed the solid rocket apogee motors that placed the Syncom satellites in orbit; a typical Syncom motor was 12" in diameter and contained 60 pounds of solid propellant.
42 JPL also developed the internal insulation and the nozzles for the om apogee motors. 43 3. Chemical Propulsion Information Agency. Solid Propellant Rocket Static Test Facilities. CPIA Publication No. 26, August E-32, Room 38, File 3, Drawer I, JPL Edwards Facility Collection. Report on file in temporary storage, Dryden Flight Research Center, Edwards AFB, California, part of the JPL Archives Collection, Pasadena, California. 40 Sharpe, Mitchell R. Satellites and Probes: The Development of Unmanned Spaceflight. Doubleday and Company, Inc.: Garden City, New Jersey, 41 Compton, L. E. and J. H. Kelley. Risk Reduction in Solid Rocket Motor Propellant: A proposed Program Presented for NASA Code Q. E-32, Room 38, File 3, Drawer I, JPL Edwards Facility Collection.
Report on file in temporary storage, Dryden Flight Research Center, Edwards AFB, California, part of the JPL Archives Collection, Pasadena, California. 42 Interview with Robert L. Ray by Richard K. Anderson, Jr. and Scott M. Hudlow, 16 August 43 Compton and Kelley, 47. JPL.EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Syncom 1 was designed for geosynchronous orbit, miles above the Earth's equator; it was launched from Cape Canaveral, Florida on 14 February It achieved the correct orbit, but Syncom l's electronics failed within five and a half hours after launch." Syncom 1 had a three-minute test tape to test communications failures, which ended playing "The Star Spangled Banner. Syncom 2 was launched on 26 July from Cape Canaveral, Florida after Syncom 1 failed.
NASA fixed the initial electronics problems; the satellite was a success. Syncom 2 was the world's first geosynchronous communications satellite;' it was initially fixed over the mouth of the Amazon River, to provide continuous communications between the United States and Europe. It was a simple spacecraft; however, Syncom 2 was larger and heavier than originally anticipated. JPL was able to modify the apogee motor to provide more thrust to carry the additional mass. Syncom 2 was a relay satellite for different types of electronic signals, excluding television. It led an eventful existence working for NASA. Syncom 2 was pushed into a position over Africa, then propelled back to Brazil, and later moved to the Indian Ocean.
The satellite could be located anywhere NASA needed it, with the limitation it had to be in an equatorial position." Syncom 2 was later transferred to the Army. Syncom 3 was a technically improved version of its two predecessors. It was launched from Cape Canaveral, Florida on 19 August days before the satellite relayed the Olympic Games from Tokyo, Japan to the United States. The satellite was stationed at the intersection of the equator with the international dateline, about miles north of the Fiji Islands, in the middle of the Pacific Ocean at an altitude of miles.
This was a central location between the west coast of the United States and Japan.' Syncom 2 and 3 were incredibly successful; their impressive performance behooved Comsat (Communications Satellite Corporation) to model its first satellites on Syncom. ' Syncom Sharpe, 125 . 5 Best1er, Alfred. The Life and Death of a Satelli te: A Biography of the Men and Machines at War with Space. Boston, Massachusetts: Little, Brown and Company, Paul, Gunter. The Satelli te Spin-Off: The Achievements of Space Flight. Washington, Robert B. Luce, '7 Paul, 49. I~ Paul, 50; Bestler, .9 Sharpe, JPL $DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 2 and 3 were later transferred to the Army, after NASA was finished with the satellites.
NASA left the field of communication satellites to civilian agencies until the late when it launched a new Syncom satellite from the space shuttle. NASA's second major satellite project was the ATS satellite project. ATS was a " ... new satellite program specifically concerned with general problems in applied satellite technology. ATS was an outgrowth of Syncom and was NASA's basic research satellite, particularly in regards to satellite meteorology, communication, navigation, and spacecraft control technology that was an outgrowth of Syncom. Again, ATSs were built by Hughes and JPL developed titanium cases, internal motor insulation and nozzles for ATS; a typical motor was 28" in diameter and 28" long and contained 800 pounds of propellant.
51 Five similar spacecraft were launched between August and August 52 The first ATS satellite was launched on 7 December and stationed over the Pacific Ocean in a medium orbit. ATS 1 demonstrated NASA's research goals; it conducted communications, navigation, and meteorological research. However, ATS's main task was to transmit telephone and television broadcasts between the continents bordering the Pacific Ocean. ATS also had spins can cameras that could photograph the region every twenty minutes. 53 ATS also on occasion relayed radio transmission between aircraft crews and ground stations; it was a versatile satellite. 54 The remainder of the ATS satellites had similar missions, except they were intended to have geostationary locations.
ATS 2 and 4 failed to achieve geosynchronous orbit but provided limited data; ATS 4's orbit decayed after two months. ATS 3 and 4 were spin-stabilized and had 56-inch diameter bodies; the remainder had gravity-gradient stabilization which required larger bodies and thus larger motors. ATS 5 had a gravity-gradient stabilization system; JPL provided it with a pound thrust solid-propellant apogee motor. ATS 5 conducted a wide variety of experiments. It had the largest and heaviest payload in the so Paul:- 60. 51 Robert L. Ray Interview. 52 Wilding-White, T. M. Jane's Pocket Book of Space Exploration. New York, New York: Collier Books, 53 Ordway, III, Frederick 1. Pictorial Guide to Planet Earth. New York, New York: Thomas Y. Crowell Company, 54 Paul, 61. first ATS series.
55 JPL.EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ATS 6 was a second generation ATS geostationary satellite launched in May It had a rectangular Earth Viewing Module as the main spacecraft body, and was equipped with twenty experiments researching direct broadcasting, remote medical diagnosis, high-resolution meteorological radiometry, sensors for analysis of space at synchronous altitude, and general technology experiments. ATS 6 was moved to a location over India in mid to provide educational broadcasting for India TV. 56 From to every spacecraft JPL launched had its liquid propulsion subsystems qualified at the JPL Edwards Test Station.
This included the Pioneer series of interplanetary probes, the Ranger lunar series in the early the Surveyor lunar landers in the mid the Mariner series of interplanetary landers and probes in the and early the Viking Mars orbiters and landers in the mid and the Voyager series which conducted of Jupiter in the late 57 The liquid propellant propulsion testing for these spacecraft was conducted at Test Stand D, built in The Surveyor lunar landers and the Voyager series also had their solid rocket motors manufactured and qualified at the JPL Edwards Test Station. The titanium case technology for the Surveyor and Voyager solid rocket motors, and the internal insulation and nozzle technology for the Surveyor solid rocket motor were developed at the JPL Edwards Test Station.
58 The solid motors were apogee kick motors to help the Surveyors reach the moon, and to help the Voyagers establish orbit around the earth before they headed to Jupiter. The Ranger series led from hard lunar landers to the Surveyor series of controlled soft lunar landers. The Surveyor series transpired in the mid in direct support of NASA's manned Apollo program. Surveyor 1 made the first soft landing on the moon on 2 June and demonstrated that the lunar surface could support a spacecraft and that man could walk safely on the moon. Surveyor 6 lifted off from the moon and moved to a new location, demonstrating the first engine restart on an 55 Wilding-White, 56 Wilding-White, 57 Gibbons and Tibbitts, 1. 58 Compton and Kelley, 47.
Jpledwards Facility
Edwards Test Stat ) P.cAER No. CA-163 (Page extraterres The late tial for Voyager, which was conce "Grand Tour" of the solar system. 50 The Grand due to budge concerns, since it project the ent by formulating a new, cal terlSaturn, which was approved and trans The were scheduled to encounter Jupiter and Saturn, and possibly Uranus. The Voyagers had enhanced computers drove the attitude control system. 51 The identical Voyager 1 and 2 were launched Voyager 2 was launched on 20 August sixteen days before Voyager 1, which was launched on 8 Voyager 1 was the first Voyager probe to encounter Jupiter, hence the name. Voyager 1 was on an easier, faster ectory to Jupiter, while Voyager 2 was a longer ectory which could be retargeted later to reach Uranus.
Voyager 1 encountered Jupiter in March four months be Voyager 2, and then flew Saturn, 20 months in November The 2 was smooth; however, spacecraft several bouts of robotic "vertigo." The ented t alarmed JPL controllers, who subs discerned a mis-setting of computer parameters. The space was unevent once the t problems were corrected. 1 around ter. It studi the planet's magnetic Great Spot, a permanent storm whi moves a counter-~~V~J~VV se rotation. Voyager 1 utilized Jupiter's gravi to lyon to Saturn. S of Saturn's revealed that are composed of " ... thousands of ringlet up of countless ice and dust icles." moons were di the known to 1 also s ed an moon, ore tem JPL EDWARDS FACILITY Test Station) HAER No. CA- 6 (Page encountered Saturn in August it Uranus and Neptune. In ts t of Uranus.
Voyager 2 studied Uranus's system, photographed its surface and moons. 2 reveal tional undiscovered Uranian moons, the total 5. 2 proceeded to Neptune, late It studied Neptune's moon ton, and discovered s new cont to transmit data the as the edge of the solar system.
The brought a major shift at the JPL Edwards Test Station away from the solid rocket apogee kick motors toward new research and development projects including many proposed Shuttle Transportation tem JPL also ing with exotic high energy solid fuels and devel new solid-propellant research The STS the "space shuttle" as it became commonly known was propos a reusable space plane that could land on a convent s The space shuttle was to be boos large jettisonable solid rocket boosters numerous tests for these new large motors, ow HCL (Hydrochloric acid) solid lants for JPL also developed a low-part ate exhaust tIe's SRB separation motors.
The STS the JPL evaluated for STS solid rocket motors us continued the insulation res loped asbestos- insulat shuttle missions anomalies; JPL Edwards Test Stat were so these problems. The JPL able to a prope eros burning evaluation ogy and i a ld scaling law for eros rate ion problems, which solved the
Jpl Facility
Edwards Test Station) HAER No. CA-163 (Page compounds as energy high energy research the demonstration of a 12" motor utilizing a propel This system a measured vacuum Isp of 342 seconds, t for propellant. JPL also researched and proposed to NASA a per (1 and solid) s system. problems were developed solved s , whi had appl ion for the entire fie of solid-propuls technology. A crowave doppler velocimeter technique combustion was perfected. JPL so loped low burn rate propellants and s lizable propellants ions, a problem dating to the early and whi JPL th the Fl Center late to develop next ion test motor- the ASRM (Advanced Solid Rocket Motor) This ect luded live motor firings, motor f , and and physical properties testing.
JPL tested igniter compounds, clean propellant, and conduc propel liner evaluations, motor s e w , and inert propel f ion for Although JPL was conduct propellant research, the Sol 1 test if teen years; the last motor work has been the sol undertaken the Force's i Site Characteristics JPL .EDWARDS FACILITY Edwards Test Stat ) HAER No. CA-163 (Page The Base es 1 floors of several valleys in Mojave Desert. JPL Facili is located 1.5 and meters (5 and 35 feet) below the sil line of eistocene Thompson at an average alti of 701 meters ) above sea AFB is located wi geologic structure kno~TI as ave ock, and is bounded the and San Andreas Fault zones.
The faulting and ift assoc with the Mojave has created a region which is geologically th both Tertiary and pre-Tertiary geologic formations as well as later Quaternary luvial sediments. The JPL Edwards Facili loca an area of recent Quaternary alluvium composed of and gravel, playa clay, and wave-deposited The JPL Edwards Facility is located within the xerophytic e saltbush communi The dominant shrubs represented in ect area lude all scale (A ex ) f cheesebush (Hymenoclea sola), golden chol echinocarpa) , creosote bush (Larrea divaricata boxthorn ( um ), rice grass ( spines ex ), and wolfberry ( um Elm trees ( at JPL facility were and rel eve some of sual starkness landscape.
Cultural Landscape and Architectural Evaluation was a complex compos of 80 structures (7 test structure, one administrat structure, The complex dates from and grew War period; building activi ceas ili had developed an extens testing of liquid and sol propuls on space probes, ites. "Geo ogy of " USGS Bulle (USDI-USGS) , 19 0; 7. JPLEDWARDS FACILITY Test Station) HAER No. CA~163 (Page around the diverse spacecraft propuls systems and ir pecul ect requirements. stor events had a pro influence the JPL Edwards Facility's ss and its cultural landscape. A tural landscape is the communal sum of the natural and built environment, , vernacular architecture, and the social and ent unite a community, luding work communities.
, vernacular tecture, and the cultural landscape are reflectors of conscious and unconscious ideas and concepts; they are storical products that reveal intent and define social and re A cultural landscape also reflects cho of and adaptations to the natural landscape and its ecological systems. Technology is viewed as " ... an expression of our culture, encoded wi our dreams, purposes, environment, insights, limitations." Unlike the highway and utility systems or the parks and buildings composing the familiar landscape of a modern city, JPL Edwards Facility cultural landscape is spare and organized around requirements focused on either liquid or sol propellant engine and motor testing.
The JPL Edwards Facility's built environment reflects exacting standards and unique construction associated with the of testing with safe for both man and nature. JPL original to western ave Desert in to escape cramped quarters Pasadena. The desert was a hostile e few people would sit or settle, so no one would object to the se or po hazards of rocket tests. Expansion room, s , and ic be easi It seemed to JPL and government that the desert was a relat barren ace I th lit Ie to suffer technological acc The test stat was Test Base, , autonomous el (later r to 5 on Purse Jr. , the of Mater ture" de. J. Schlereth, 98
Jpl Edwards Ility
Edwards Test Station) HAER No. CA-163 (Page on Muroc test stat JPL Test Stand (Test Stand "A") additional to support the vital testing at Muroc. The Muroc test remo ; JPL personnel from Pasadena stat and drove to it to perform engine test The tituti of the JPL Edwards Test Stat evolved s and Building sites were needs were ified. While JPL did not have an master plan encompass all future development, were some overriding iples that guided the facility's ad hoc land use planning. Construct decisions were made on an individual, building-by-building basis as various missile and space probe programs were implemented by the military services, NASA, and Congress. Decisions to add mew structures to the ility were react and geared toward meeting challenges and solving problems.
Army Corps of Engineers (ACE) built, planned, and laid out the ORDCIT test station Other than the advantages of a remote location, the only major environmental factor in planning original test station was the prevailing eas wind. The Corporal Test Stand was built to t t downwind. Support structures were t to west and south of the test stand to escape fumes and ~~.UCAu~t ts assoc ed wi tests. JPL also planted elm to the desert environment a little more e for human beings, but recognit of conflict between a more luxur natural and the of exotic t~~uu.ulogy, no were east of the test stands. Three planning iples drove the test stat 's expansion and and played a prominent e in the and building campaigns.
Test S D (as 1 s liE" and "Gil) all lie along a north-south Test Stand (the original Test Stand) structures and and Recording Center) of 1 JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page could secure th little of spread to other structures. surface was so scraped of natural vegetation 50 foot zones around each building to further inhibit the spread of fires. s oxidizers were separated at each test stand liquid propellant area-- oxidizers to the north and to the s north-south relationship ed over sol storage area and even the id manufac area, as can be seen by referring to the map (HAER sheet 1 of 4). development of the solid propellant manu turing and testing line the continued in the above vein.
Fuel and oxidizer storage, flammable waste storage, and the waste disposal burn unit were all widely separated and located to the east of the main north-south axis, guaranteeing that no fumes or s from them would fallon inhabited support structures to the west. Sites for the manufacturing and assembly of solid propellant motors were spread broadly to the west of the north-south axis. Though hazards of fire and explosion were associated with many structures this area, the quantities and toxicities were of smaller and lesser concern than the liqu s. Unlike the liquid propellants, sol propellants were not hypergolic or , so many of the safety hazards and handl problems associated wi liquid lants were obviated.
The solid-propellant process 1 structures are clustered by function: grinding and mixing bui are grouped together, the cure buildings are adjacent to each other and the conditioning structures are cont Along the remotely sol lant 1 , fuels and oxidizers were ground, solid-propellant rocket motors. motors ~vuu,~tioned, and test f Facilit sol lant measurement and ray Facili inspect sol and voids. process ent JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page cast motors. temperature the sol propellants. A 5' x 8' Baron autoc of composite component fabrication materials up F. An lab prepared igniters which were instal motors at an ass building or at the test stand. i ities for wastes and an incinerator were also included.
The sm overr importance ascribed to technological advances during the Cold War, and demonstrates how rapidly technology and corresponding social and cultural changes occur on the landscape. The cultural landscape reflects the changing needs of the burgeoning post- World War II missile indus and of a modern deep space research and development facility.
The spartan architecture of most structures at JPL belied the importance and the radical nature of the guided missile and space probe tes conducted at the ETS during second half of the 20th-century The ACE initial utilized temporary architecture, construct techniques, and materials drawn from its extensive in Ii hous The Test S (Test Stand "An) was of necessi built of concrete and steel, but the structures were wooden buildings whose character was C'''~LJ.~scent of Wor War Ii quarters. Most of the support structures t the liquid propellant test stand area were of construction.
The ACE's design responsibilities ETS when the facility came under NASA's s in The and structures of the solid- propellant I by Austin, Field, and Fry of ous contractors, and the JPL Plant th advent of the solid propellant line, fireproof steel-reinforced concrete block was building Despite the retention and engineering firms, however, lant 1 make no stylist ic or ign pro sionals buildings are s serves some indus contro or ations at e roofs and wooden JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page concrete, Ie me grating is the of choice s and mez Roofs are commonly of wooden construction covered with plywood, hot-mopped 5 roofing paper gravel.
Most of e buildings are windowless, one s f roo structures finished with white Concrete walls are cally 12 inches or 8 thick, as mandated r Force regu ions for structures containing os the administration building (E-32/4231) and weigh and rol building (E-35/4234) have windows. (The administration contained off removed from the solid processing line, and the weigh and control building had narrow bulletproof windows observation purposes; windows are excluded from other structures for better internal environmental control.) A maj of the processing buildings have two-room plans with no doors. The main room is the workspace; second room is a machine room which houses spec iz control equipment.
This floor plan offered not only the standardization of functions, but also architectural simplicity for f i g h t e r s and emergency personnel. The primary entrance s a ly placed heavy strap-hinged steel blast door; of many of these are designed to permit the steel I-beam of a monorail hoist to protrude beyond the doors. Other doors are usual of grounded steel construction. Each building has a lightning rod on each roof corner, and many have grounding systems for personnel and conductive floor finishes to ground static electr c s generated by personnel or machinery. Some structures e "blow-out" or blast walls and doors constructed of e trostatically conductive t to pressure of an explosion with little damage to the structure.
Electrical systems are ly metal conduit, and the ec I ldings are of explosion-proof design. suppression systems are prominent in all processing buildings, and emergency shower and eye-wash stations are standard f at every tructure. Emergency slides, a common saf ion, are present on several roo s and mezzanines. Most " th a ground level wastes or ities of sion at each leanl s of an indus ~ J..u-HAMf>JU. F,OUNDRY A:'I~2.8 ':.:o.R AP..PROVE!D EQUAL INVERT ELEV. . /L ~OZ.l;G ';: TECHNICAL SEJtVICI!. S/I'(! MtN:,.,:I \~ato;~n:::OXJD IZ:E'n'!>l:.ENDEl\. pipl!t' in/t!'1: .:r.~aG:n ,:::OXU::UZ.ER GP.INOEI\ .u..-.J' 2.:~O.7.8a AOOITJQHJO: E .~7 .....-.l-f'INlET '. Precast r;onc. piP'? I'll c'" C;!ti"C; a (, It"a.c. EACH WAY " U 1I3@/O" .W. . () '!)~"4elZ. O.C f:.ACH.
WAY y 'D +' 0' t-< CHEMICAL / HOLD,ING PIT ~ SCALE: NONE 5. ~~ ::oro [fl Zit o (J) -0 It OJ n OJ n Fig. 21 <.0 Examples of JPL Chemical ts ro I f-'!---'OH U1 ~ 2 w~ >< JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page building's design was t with its Building Layout and Air Force Safety Regulations As an added sa precaution structures are surrounded by blast gases and shrapnel upward and away from event of an ion.
Every building is -s pole on which rotating ety 1 (see they indicate the status of as lows: lights Light: Extreme Hazard Amber Light: Conditional hazard sts Green Light: No hazard exists No light: Indicates an amber light condition regulations mandated that two personnel always be when conducting any hazardous operation; hence building ans had to accommodate at least two and to move around various machines. 76 The operational status of the stand-by lding 4275/E-76 was constantly checked. JPL staff recount that they were vital when the commerc 1 electric power led during grinding or mixing ions. Building the Solid Propellant Processing Line The JPL Edwards Test Station quadrupled area the solid-propellant processing line was trans to ETS from Test , Room 7!
Facili lection on f Fl Center, Edwards AFB f JPL Collect Pasadena! JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page AMBER "0 OJ WARNING UG~r DETAIL C FlXTlJRES ME FEDS<AL JJf SolS o:x.oR AS. SHOWlJ St JPL EDWARDS FACILITY Edwards Test Station) H..AER No. CA~163 (Page The JPL Edwards Test Station erected a new secur cy fence, added approximate 575 acres to the ETS complex, constructed the solid~propellant processing 1 , constructed the storage area and new docks, built an rcraft hards and la f a linked the JPL Edwards Test Station with the Base runway.
The addition of the solid-propellant process brought an influx of JPL employees to the the early 97 employees worked at Station at its zenith in The original solid propellant processing line, when completed in consisted of twenty-seven buildings laid out in a semi-circle around the liquid propellant test stand area Future building campaigns in the solid-propellant area were integrated into s plan. The new site plan and buildings were igned by Austin, Field & Fry of Pasadena, California, a local architecture and engineering firm. JPL was a major Austin, Field & Fry client. Since the JPL Edwards Test Station was located on an r Force reservation, major site planning criteria were the Force regulations concerning explosive safety standards.
These regulations governed building construction, intra-building stances the quantities of propellants lowed anyone structure. Distances and limitations on the weights of ous propellant classes at JPL Edwards Test Station were splayed in a Koebig & Koebig on a sheet titled " stances. "78 s landscape pattern s Se-uuU,U-J- materials. The greater the number of os ,the larger the complex. This ext ens ex, due to the to Idings so that a potential osion structure. lant processing line was t over construction phases. In and 196 , of Sherman Oaks, California and Ruane Gabriel, Calif built 01 and testing facilities. sol the s area cons sts 0 , a 1 , a JPLEDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page weigh and control building, conditioning buildings, cure v~~u.~zer buildings, mixer and cast building, an unit, preparation complex, oxidizer and fuel s , a test stand, a solids assembly bui , an , a tunnel extension with blower house, and a tunnel A second building phase in and constructed f new solid propellant processing ldings luding a weigh and test preparation building, s lization ility, weigh and storage building, an ignition lab, and a test stand. This construction phase was built by J. D. Dermody Co. & Ralph Walker, Inc. of Lancaster, California and by Santa Fe Engineering of Lancaster, California. Austin, eld & Fry designed these buildings and located them wi sting site plan.
A third construction phase began and lasted through This phase construc buildings which had redundant capabilities 1uding oxidizer storage, propellant processing, oxidizer dryer and blender, and a casting and curing building. A separate X-Ray building was also constructed to house a new X-Ray machine, which was purchased from Lockheed t ion. These buildings were constructed firms: Joseph D. Gee Construction Co., Barstow, Construction Co., Lancaster, i and E. C. Morris and Son of Lancaster, California. These were the specific buildings constructed for the solid propellant process line.
These buildings were placed on Aust ,Field & 's site The test station's tecture tural continued to ref t its driving principles story; it eventually became a compli~c'L'~u landscape coexisting with a desert eco Solid Propellant Preparation Parameters JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Ii (to wi aging, extreme and envi changes), mechanical strength (to maintain shape, its own weight, adhere to the motor casing during storage and f ), ease of handling (light weight, low ity), ease of manufacture (few steps, safety, reproduc Ii of las), lowest cost, and least toxic exhaust byproducts. At one t , s Ii and sterilizabili were factors motors of probes and landing cles.
In addition to these tors, the particle sizes for fuels and oxidizers played a tical role in the reaction rates generally, the smaller the particle size, the more rapid the reaction. Another problem concerned the mixing of lant components sufficiently to insure their uniform dis ion throughout the propellant mass; uneven distribution fects burning rates and motor performance, and can even cause failures. F , the reliability and repeatability of formula batches was - the ninety-third batch of a formula should have the same mechanical and performance characteristics as the first to make motor performance predictable. Aside from the composition of a propellant per se, the des of the propel grain was important to the ormance of a motor.
JPL scientists in conjunction with other researchers found that a hollow, cylindri grain with a specially shaped hole along the central axis of the grain gave much better The burning rate of a motor is related in part to amount of area the hole exposed to combustion; all factors the same, larger the area exposed to uwt ' - ,-'LLU.) ter the motor burns, and the more energy is time to propel a rocket. Taken to extremes, too small relat to the mass of propel to e~:arnple, a narrow hole in a narrow cylinder of motor may burn too slowly to be of practical use; enough thrust to lift the motor or its rocket On the other hand, if the exposed area is large to the mass to be burned, the propellant burn more than the tant gases can escape the nozzle, creat must be sought.
The answer cal hole a grain most cas motor , the area to combust is released per second. In other nc:rE~a;ses, and the motor's we decreases. erned th a JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page presented a surface area to combustion than a s e for a given diameter of ho . As the star shape burned, it ultimately became a cylinder with a ace area similar to original star-shaped hole. The result was a motor with a much more even burning rate than be Other configurations of e were researched, as well as the proport of area to propellant mass for various propellant formulas.
It is also conceivable that some propellants worked better in motor designs than others; in this way, propellant formulas could af t motor design, constraints on a motor design could affect propellant formula chosen. Analogous problems applied to the s composite materials used to fabricate the motor casings and nozzles. While a solid propellant formula might t des e characteristics, the motor casings and nozzles had to be correctly designed to take advantage of them. Casings had to be lightweight, yet withstand the pressure generated by burning propellants, as well as the heat, and they had to be made of substances that would not react with the composition, or respond to environmental conditions ( ,dust, heat, cold, vibration) such a manner as to fai in s or flight.
Light metal alloys (such as titanium alloys) and epoxy composites (boron epoxy, graphite fiber epoxy, Kevlar epoxy) have been success tested at JPL-ETS and have flown ssions. Nozzle materials and engineer sign also had to be careful developed. Nozzles were subjected to the s of t flames. If their Is were not care en, the nozzles might melt or burn away depending on flight time. If the nozzle ts were too narrow, the resulting high speed of hot gases through them might quickly erode them and cause failures. Too wide a lead to less than optimum thrust. Composite s such as impregnated phenolics have found to perform well in nozzles; char and withstand motor's me s melt.
The exities Ived numerous, and it was ETS's use propellants as well as motor des ions and a sys manner Ie JPL .EDWARDS FACILITY Edwards Test Station) K~ER No. CA-163 (Page imposed by s and NASA. It years to establish t propellant formula for a given motor. The id propel 1 was designed to be fl enough to accommodate a wide ety materials and test situations. NE:vE~rttle_Less, the l ' s layout, building designs taIled equipment bespeaks a commitment to sol t motor ~~uu.vlogy based primarily on rubber-based propellants ammonia compounds as oxidizers. While the Control and Recording Center 4321/E 22 oversaw test f of solid motors and liquid-fueled engines, the We and Control Center 4234/E-35 oversaw the production of motor liners and the grinding, mixing and casting of solid propellants.
A diagram by JPL employee Bruce H. Morrison outlines the process apart from buildings in which it took place (see Fig. 23; see the HAER drawings for integrated building and process diagrams) . Aside from the fact that Morrison's diagram shows the production of multiple for large motors, the production steps remained the same throughout the history of the solid propellant line. The absent steps in Fig. 23 are the storage of raw chemicals for propellant manufacture and the disposal of wastes.
Most of the detailed process discussions below are based on rules, Standard Operating Procedures (SOPs), propellant batch rec storie and contemporary engineering drawings, storie photographs, and other records which come from various periods and re occasionally to secondary truments and moved around among the buildings a t, on the various propellant programs. Some ssions e records exist, and where poss these are after some analysis. Propellant Ingredient Storage concerns are mani t the cultural andscape by s ex. Physi separation ted of hazardous materials is a S~~UV~L of cape.
The 150 feet o I M y "d t-< tr:I Q;y t-< "d Ii Q;tr:I tr:If-3~ ::um::u (Jl tJ o W Iij v rt~ ~ () (J) Fig _ 23 I t-< f-' f-' 0 H Bas JPL id Propellant Processing Diagram U1 O\::J f-3 w~ r< JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page one-story, ground level corrugated metal s are present as 1. Idings 4250/E 51 (Sol Storage) and 4251/E-52 (Sol Fuel Storage) were both original built as x open and later converted into closed s bui ; the second shed at Building 4250/E-51 was built in and roll-up doors were installed at all three sheds at that time. are supported by steel I-beam frames bolted to poured-in-place concrete foundations.
Concrete hazardous waste retent bas for collecting hazardous material spills were constructed at each of these buildings in A plumbed emergency shower and eyewash station is present at each building. All three structures are naturally ventilated. Oxidizers were shipped in fiberboard drums weighing approximately 250 pounds Kg) ece and stored at ambient temperatures. Safety rules limited the capacity of 4250/E-51 to pounds Kg) of Class 3 materials and three personnel. All personnel had to wear flame retardant clothing, and they were not allowed to dispense oxidizers or store f shed SO propellants in the structure (N0 2 a Class 1.1 high explosive, was occasionally used in some propellant formulations; HMX was stored under rigid standard operating procedures in Building 4281/E-82 81 ) .
Oxidizer drums were usually stored and removed by fork-lift; marked trucks delivered the drums to Weighing & Storage facility (4269/E- 70) . composed fuels, among them PBAN oni Ie), powdered aluminum, These propellant components were at ambient temperatures in did not permit two or more different same bay, and the building was so Rules, Solid 1 15 il Collection. Fl Center, JPL Collection, Section 35 , Procedure ) JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page res to a maximum capacity of pounds of Class 1 materials and three personnel. As in 4250/E-51, personnel had to wear flame retardant clothing, and were not permi to dispense anything the structure.
82 Oxidizer Weighing and Storage When propellant ingredients were moved for use, oxidizers were taken to Building 4269/E-70, Oxidizer Weigh & Storage, while fuel components went to Building 4234/E-35, Weighing & Control. Building 4269/E-70 was allowed to hold a maximum of pounds Kg) of Class 3 oxidizers in its 20' x 28' perimeter; four personnel were permitted during operat 83 JPL specifications for ammonium perchlorate ("AP," NH 4) required suppliers to ship AP with a minimum puri of ( and in a limited range of particle sizes.
84 Other oxidizers used at JPL on an experimental basis were ammonium nitrate (NH 4N0 3), sodium nitrate (NaN0 3), and ammonium sulfate these were substituted for AP in attempts to remove chlor from motor exhaust products, but the sacrifice in reduced specific impulse per unit of mass made their use in propellants impractical. A typical propellant formula contained about 70% ammonium perchlorate by weight; this proportion rose when less energetic oxidizers were used. Bailey, Richard L. Safety Rules, Sol Propel Engineering, Section Building E 52 15 January E-32, Room 7, Shelf 2, JPL Edwards Facility Col tion. Report on file in temporary storage, Dryden Flight Research Center, Edwards AFB, California, part of the JPL Archives Collection, Pasadena, California. Bailey, Richard L.
Safety Rules, Sol Propellant Engineering, Section Building E-70 15 January E-32, Room 7, Shelf 2, JPL Edwards Facility Collection. t on file in temporary storage, Dryden Flight Center, Edwards AFB, California, part of the JPL Collect Pasadena, California. Jet Propulsion Laboratory, Cali California. JPL [ification] October Test Specification Me thods , p . ( ). s creen, screen, 2 to screen. Research Center, llec ion, Pasadena, JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Operators wearing flame retardant clothing zer drums and careful screened the contents; in some cases, ~~~~.~zers were weighed and loaded directly into hoppers destined for the Baker-Perkins mixer Building 4233/E-34.
More ten oxidizers were sent after weighing to Building 4235/E-36 or 4283/E 84 to be ground to particle sizes required by specif formulas. weighing of large batches was accomplished by a floor- mounted Toledo scale of pounds Kg) capaci ,while smal batches were weighed on a scale of 200 pounds (91 Kg) capacity (see Fig. JPL operators attached grounding straps to all scales and other equipment when work was in progress. e readouts and other electrical gear related to the scales were installed in explosion-proof housings to minimize the spark hazard from elec malfunctions as well as to exclude any accumulations of oxidizer dust in the instrument mechanisms. Scales thems were supposed to be kept scrupulously clean of oxidizer build-up.
No organic materials or solvents were permitted in the building during operations, since their presence near powerful oxidizers was an invitation to fire. Oxidizers were transported to the "grind houses" (4235/E-36 and 4283/E-84) VeloStat -lined fiberboard drums of 250 pounds Kg) capacity. The I is an electrically conductive plast which forms both a moisture barrier and a grounding mechanism for the contents. Oxidizer Grinding Building 4235/E-36 was built in 63 as a 14' 8" x 8" re concrete structure th rooms; Room 101 was the Grinder Room, Room 102 the Building Equipment Room, and Room 103 the Dust Rece Room (see F .
25) .85 Building 4283/E 84 was built in to the same floor plan and dimensions as 4235/E-36, except steel frame and Transite board were used to construct the walls instead of concrete (see Fig. Aust Engineers West Thi Street, Los "Edwards Test Station, Jet s l Institute of Technology, Force Base, , Calif E-36, Grinder plans, Elevations, Sections & Details, Sheet A-37 (6 of 26 June JPL No. E36/1-0. California Institute of Jet s Laboratory, Plant tructures at JPL Edwards of si and Construct Office, Propellant E-84: FIr. Plan, Elevations & Sections. . No E84/ -0 Cali Inst JPL ~EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 102 Building Mechanical Room Mezzanine Scale Pit 101 Weigh Room I Fig.
24 Building 4269/E 70/ Oxidizer We~~H~H~ & JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA~163 (Page Chemical pit ow-out Wall Monorail HOist\ 101 . - - -. . ~/ Grinder Room Emergency 'Shower and Eye-wash ! 103 -3 ! JPL ~DWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page \ Emergency Shower and Eye-wash Station Transite Panels / Monorail Hoist / Building / Mechanical Room Dust Receiver Room Mechanical Systems Pad Fig. 26 Plan of Building 4283/E-84, Oxidizer Grinding JPL .EDWARDS FACILITY Edwards Test station) HAER No. CA-163 (Page 283/E-84 was serve as a back-up for 4235/E-36, occas~vuu.~ tigations idled the building development and test es.
87 The SVULLL1C,:::t,;:, Grinder Room in 4235/E-36 was construe th s foam insulation a frangible or "blow-out" wall an osion; 283/E-84 dispensed wi this provision the 1 thick" . asbestos sandwi panels wi " walls the same funct Both buildings were by and were a maximum of three pE~rE,ol~ne~, 600 Class 1.3 or 120 pounds Class 1.1 oxidizers. The each building was a Model 1 SH Mikro- th stainless steel hammers capable of (59 Grinding could humidi stood between 20 and and could be adjusted by environmental system Room 102 f necessary to permit grinding operations. were required to wear flame retardant clothing and rators if exposed to oxidizer dust. to , an 10-mesh screen was hopper to remove any foreign matter be it hammer An warning light was a loose nut which fell a E- 6.
sprinkler system JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA~163 (Page turned on zer was Aluminum scoops do not accidental s masonry or metals) and electros cal conduct were mandatory transferring oxidizers to the mill hopper. Ils were to be cleaned up with cl treated as purposes. Operators had to 1 a second screen (per propel formula governed the f size of v~~v,~zer icles. They also had to adjust pulleys and belts eve the requisite mill speed for grinding the required particle size and quantity of oxidizer. Once the VeloStat 35- lon fiberboard receiving drum had been positioned beneath the mill and the dust receiver checked, grounding straps were attached to 1 machinery.
Typical set-up time took about 15 90 Personnel were cleared of the building and a warning light was turned on before grind ions The was remotely operated from Bui 4 34/E-35 and tored by television and crophones. During operation, the charge was to the mill automatically by a vibrating hopper and repeatedly ground until required fineness was obtained. It took about 3 hours 0 minutes a 120 pound charge to make 4 passes through the 1 and sift an screen. zer t 1 was a 5-horsepower Roto one Type N tat (dust absorber). All the oxidizers ground 83/E-84 were water-soluble so removed them the by water spray. Fo the drum was sealed and removed, then the domestic water a hose, and ). The grind house had to be clean f t; tools and parts were washed, ed, and at the close of operations. After 140 F.
every JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page and were E-86, 1e size dis were optical by cromerograph. JPL me~kJV~A~~U.~ charac and condit of every substance at every step manufac a propellant batch, both to enSure ity and maintain consistency in propellant formulations for performance analyses. Some formulas cal for a -modal oxidizer, meaning that specific we discrete part le sizes could be red. Drying and Blending of Oxidizers Many JPL propellant oxidizer particles of a particular size or of oxidizer at certain specified ranges of size. To meet these specifications, portions of several would be weighed and blended in the tumble dryer/blender 4237/E-38, Oxidizer Drying and Blending.
Some also contain addit which are extremely sensitive to moisture prior to casting and curing. For these propellants, oxidizers must be carefully dried at 4237/E- 8. If ~~ were called for, particularly s and meticulous procedures were mandated for ety. When 4237/E-38 was built in JPL installed a Patterson-Kel Model 304 blender manufactured in , Pennsylvania. Thereafter other equipment such as f elec scales, an zer particle size , and a oven were talled. An f c was so i to equipment. Iding 4 37/E-38 i concrete block structure measuring across the along the s It has two rooms' Room 101 is the Room and Room 102 is the Room.
The four corners of structure are th 12 square s concrete columns, and the southeastern facade adjoining 101 i blow-out ted 2" 6" studs c,urnfoam two of ene Room 101 is a No. 20 3 AFB, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page \ Chemical ... . - ~ . 0 . Foundat (dashed) " : ; .; Blow-out Wall I I I I I J ~o~ Dryer Room I 1 Hoist . 27 JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page 1 and enclosure for r;r,ro.r/blender. chosen as a struc material it steels) in the presence of oxidizer t if accidental struck ect. lding 4284/E- 85 was built Ibl for 4237/E 38, but the necessary tal The tumble perchlorate, ammonium trate or sodium nitrate. of compound was permitted at any time in the building, which was for a maximum of 600 pounds Kg) of s 1.1 zer and personnel.
93 The blender had to be washed out domest water and dried before a dif compound could be introduced into it. The presence or storage of greases, oils, or solvents any ions with oxidizers was express safety rules, and personnel were required to wear flame-retardant clothing eye protection. Respirators were mandatory when t was present. Only non- tools essent to work were permitted in the building, and had to be accounted for at the beginning of set-up to be sure no tool was acc the ender as to cause acc Prior c hot water heaters, a pump were started the room.
with a water jacket that 190 F to dry the t's contents mercury is drawn the unit during t rotates (tumbles) to agitate the contents To the blender, lifted to the mezzanine above the blender by a fork 1 hoist Austin 311 West Street, Los Station ex-- I, Insti of Edwards Dryer Building: Plans, Elevations, Finish Schedules, l JPL.EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page turner. Drums had to remain iand drums of ammonium perchlorate on the floor due to the compound's fr Personnel, equipment and oxidizer drums were anytime operators were trans and the dryer/blender. Up to 500 could be added to the Iblender funnel. The ronmental usted to maintain the building of 80 F 5 F and a relat humidi of blending operations.
An amber warning light was turned on while oxidizers were being dried or loaded or unloaded from the unit. When ammonium suI was processed, a green light was displayed due to the compound's inert nature. Before drying blending began, determined that the vacuum in the unit had reached 0.3 inches of mercury, then they closed and locked the aluminum wire caging surrounding the unit. JPL personnel moved to Building 4234/E-35 and control from there. To begin, the unit ran vacuum for 3 hours at 180 F 20 F. The water temperature ler was then set to 50 F and a fan t was engaged to reducing the of the water circulat / the temperature declined to 1 0 F, controller was turned off and the unit ran under vacuum thout heat.
If a blend of var ous sized has not cooled to 140 F F optimum) by of was under vacuum. At the close 0 was the dryer ender to release the blend was scooped elec cal fiberboard drums, 250 per drum. Four taken from each dried charge, sealed sture proo and appropriate labeled s. Drums were sealed and trans to Buildings 4269/E 70 or 4 0/E-5 temporary st if they were not ate JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ction, t, or any ~~'Lll~JLJUQ.~Lon of these conditions; it lS more powerful than TNT trotoluene) but its melt it use high temperature environment of burning propellants.
, numerous precautionary steps were and introduction of HMX to propel hazard with HMX is t of c , so the f t ty measure handle it is wet as far as propel process In HMX was shipped to JPL 200-pound capacity fiberboard drums and s at lding 4281/E-82. Inside each drum was a sealed polye ene bag containing canvas bags, each of which of HMX equivalent) wetted with at least 10% ( weight of of a solution to reduce its sensitivi to detonation. The shipping solution commonly contained 40% alcohol [(CH3)2CHOH] and 60% water; sometimes DOA ( [ (CH ( )4) was added as a desensitizer, but were warned not to count on ts presence. two JPL personnel were permitted 4281/E-82 to move HMX canvas No spens or transfer of HMX from the bags to was the s area.
Personne were wear co (to ze electrostat spark ion), f coveralls, eye protection, and and Canvas bags of wet HMX were at th a VeloStat bag. Ie could be tion at 4269/E-70, not be structure. SOPs HMX to 0.2 on grounded S~aLCw From 4281/E 82, JPL in two ways, ac to S.O.P. No. th DOA and JPL EDWARDS FACILITY Edwards Test Stat ) HAER No. CA-163 (Page i r 1 in a ( uuu,-"",,--ifi building 97 ) and cast the VacuDyne trays, or could trans shipping or canvas bags t trays in 4237/E-38. Personnel 4237/E 38 when HMX was present had to wear cotton and clothing, and flame garments had to be sprayed with an anti-stat vu~u.,--tive and wrist straps had to be worn and anti effec s confirmed and recorded by us an resistance meter on each operator.
All tools had to of non-sparking materials and effectively grounded. trical wiring at all plugs had to be checked for frays, and area and personnel "snooped" with a static meter to be sure no charges than 50 volts were present (as measured a 2" stance). are numerous and highly detailed for mixing HMX and and transferring wet HMX to dryer and HMX to appropriate containers. If a quantity 0 HMX were to be mixed, the drum was weighed to the nearest 0.2 pound 4237/E 38, and the we of HMX the was estimated by a simple formula. All f s were When drum was moved to a mixer building, a VeloStat was laid on floor near the and bowl rolled out onto it. The had to be large enough to extend two feet all sides the mixer after it was ro l o u t , and had to to the bui ground system.
such operations were in mixer at buildings 4232/E-33 and 4240/E-41 were losed and amber warning light on. operators placed the drum of HMX on the VeloStat t and trans required amount of HMX to drum was then sealed and returned to 4237/E 8 Q~Q~U, all f were ). A solution of JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page DOA and i to the mix , and the was ions were stati had posit on the to 4234/E bowl was and the out by remote 1. average was 30 minutes at atmospheric pressure, soeea, and a temperature of 80 F. When mixing was eted, the bowl was lowered by remote control be personnel re-tULtL building. Before the bowl was rollout, a new VeloStat sheet was laid out on the floor and grounded to the bui~~~L'c~ Personnel scraped the mixer of HMX us conductive, non-sparking spatula.
cleaned of HMX traces with cotton rags th anti stat solution; waste was of tat -lined drums. Operators then S~~~u.~ess steel or aluminum dryer trays on the VeloStat sheet after weighing and recording the tare weights of set weighed of VeloStat in VeloStat extended at least 2" above They wet HMX the and spread it out a 1" , non-sparking Personnel, , scoop grounded to system. After the enti and bowl wetted co ton rags or paper towels, of the article waste HMX as ore. of wet HMX to the a van JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ~vuv,~tions were monitored by tel sion from 4234/E-35. At the HMX was allowed to cool to 120 F the oven to release the vacuum. HMX samples 20 grams were taken and checked for moisture content.
was cont uu;;:;.'-< if necessary, otherwise, operators proceE:dE2d to transfer HMX from to grounded VeloStat bags. One at a t from the oven and weighed on a we of a tray was recorded on HMX Drying Record, tat bag was placed on the balance, weighed, grounded. With the bag still on the balance, the HMX was (not poured) into it using grounded, non- or VeloStat scoops from the dryer trays until "exact pounds were transferred to the bag. This was until the tray was emptied. The res HMX was transferred to the last bag and weighed to the nearest pound. t r a n s , the operator, tools, tray and were all grounded to each other as well as to the building ground system. The of the oStat bags were sealed " on, Is attached with batch number, weight, and other data recorded on them.
The bags were placed a f a VeloStat bag; the drum was 1 ide th aluminized tape to create a for of any static elec city. up onductive, non-sparking brushes and tat bags; residual spills were and bags are careful sposed containers I th were grounded at all Fuel Preparation was be specificat ons, 4234/E- the So,...,"'Y'''' I of chemicals was was f we JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA- 63 (Page tens le s , sensitivi elec , storage life, s ,etc In t to tances already mentioned, an of prope lant ents dated 24 1 lis 593 substances nitrocellulose t to beryllium castor oi , eOOXleS t "t fings" and napalm soap.
of the listed substances are gaseous, or ha or otherwise raise pecul handl ion of wide-ranging search for any use s to the production and refinement of success sol propellants; needless to say, the list expanded as time passed to lude numerous complex organic and inorganic compounds sifted from the burgeoning world of commerc and chemis A number of these compounds were required small amounts experimentation purposes and could be stored at Iding 4234/E-35. More frequently used fuels such as aluminum powder were stored in bulk at 425l/E 52 th smaller amounts at 4234/E 35 as "ready storage." One of hundreds of successful formulas developed at No. PBAN-Mod.
8 (used sol boosters of NASA's tle), consists of of ammonium orate, fine aluminum powder, , and PBAN (polybutadiene ic acid acryl Ie, an e tomeric or rubber-like binder that also serves as a ) The final product a gray color, a densi of per , and resembles a pencil eraser cons Polyurethanes were used and po enes are used for rubbers are among the most common rubber tons were most pages) "Current as of th code Room lOt le JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA~163 (Page Building 35 i respec s heart of the sol propel process , s e it the control room remote ion cal and mixes the wide varied fuel~and- components of solid propellant formulas. Building 4234/E was original constructed as a 51' 6" x 33' 4" steel-re concrete structure.
From , the bui the same no lIs tecture that been The was itioned into seven work rooms and a by wooden s walls (see Fig. The x wing room on the t corner (added in had or access to the lding and served as fuel binder storage. Adjacent to the east of fuel binder storage was fuel weighing room, followed by the oxidizer room. North of the east~west corridor was the control room in northwest corner of the building, an equipment room for conditioning machinery, and to the east of that, an equipment storage space. The eastern end of the building was taken up by a clean~up bay washing, cleaning and decontaminat laboratory truments and containers. The Iding equipment room was the only room other than the fuel binder storage room not to have an interior door to other spaces in the building.
234/E-3 became inadequate. An open s me roof was added to the southeastern judging from the safety rules of 15 of the room functions had been modified between In the interior was extensive two new rooms were added to the eastern end of (See HAER photo CA- The control room was a er unt was completed. The new control room (Room 01) expanded about swall up the old fuel room to occupy a space f Technology, Jet sion Laboratory, E-35 Addition: Storage Room Addition. JPL No. E35/9-0. i sion Laboratory, Plant structures at JPL Pasadena, s on Laborat Addition to Weigh Move, "'" _ walls da&hed in 102 rooms added in Control Room 1 0 9 - :>- ), 101 106 o " y '1j L' Concrete I ~ :;oro Drain Trenches Ul lding Zrt o --.
' \J) ITJ rt H I L' f-IO H 0'I:::l1-j 28 ~w ~ r< an of Bul i 234 E 35, We & Control JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page across the western end of The room its tion was as Room The s room was renumbered as Room 103 and storage. The end of the old cleaning bay its t and was renumbered as Room To the east of Room 104 was a new room designed to and store at 140 F. The oxidizer room Room new weigh room. The binder room old t Ie the SVU~UClH end of the old clean-up bay became Room a ical property laboratory later converted to solvent s To the east of Room 107 where the shed wing had stood was a new cl room with a roll-up door on the eastern wall. A new concrete apron was constructed on the south side of lding, retaining access to a dry well, but t.
Avai e handling of propellant components at 4234/E-35 is retardant clothing was required for any hazardous ion The simultaneous presence of "incompatible" (such as a fuel and an oxidizer) a room was prohibited. and equipment were to be cleaned after each operat ety goggles and breathing apparatus to be worn when handling certain substances I TDI When powder was connected to ) ) were to be In rooms in 4234/E 5 personnel as fo lows Room 10 : 0 propellants 5 Room 10 : 0 lbs lants 5 Room unknown 5 Room unknown unknown Room 50 5 personnel Room 70 5 personnel Room 10 personnel Room 08: 0 5 personnel 1 JPL .EDWARDS FACILITY Edwards Test Stat ) HAER No. CA-163 (Page I ors, lr I of s is revet barricades, which were built to ts at structures.
Explos still rested on heavy marble benches a "ghost" on f until recently. The had a conduct coating to disperse stat The dense marble benches helped to damp and e erroneous sensitive truments. Readouts were out on paper tapes as well as recorded by to that an ingredient had been weighed to the proper quantity to , and to check against human error a (see HAER photo CA-163-N-6). Electr equipment such as scale meters and fluorescent light were hous osion-proof fixtures. Other rooms were sited for s were largely empty. components for a fuel slurry were prepared at transported them to a mixer along a If quantities were small enough, they were hand- te ; otherwise were ~r~nollant s were to ed by a sol propellant s~llcu.ule specifi at hand.
Motor Casing and Liners have to the heat and Typical between propellant. the L casings contractors, at 0 t compounds, them to cas oven rooms or an JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ~~~uu~zed an autoclave (see If a propellant were cast a no other preparat , it would 1 to Such propellant "pull-aways" that were faster than intended, results. A 1 was a preliminary coat insulation, having properties that would ion and the lant. Liner binder a filler, which consisted of tos (Mg 3 (S ) (OH)4) in the and silica (S ) and other refractory substances were also After asbestos was banned as an environmental hazard, phenolic (a plas ) loons were substituted. One liner formula consis 18% phenolic microballoons.
JPL employees washed insulated cas baths of TDI (toluene 2,4-di-isocyanate, CH 3 C6 H3 (NCO)2)' a solvent which prepared rubber surfaces for the 1 materials (TDI was also used as a curing agent propellants, and sometimes propellants were cast into casings after the TDI wash). TDI was kept in three stainless s wash Room drums of TDI had vent valves on them set release vapors to atmosphere if pressure psi SOPs personnel to wear f , rubber gloves, goggles and breathing ) when handing TDI or other solvents Two people were required to work together , and any spilled TDI had to be immediate ammonia and water solution. All f es had to be cleaned up ter every TDI wash, liner materials had in Room 102 were applied to cured the 4232/E-33 oven The or sur of (probably in 4243/E-44) .
tself was a s 70' 7- /4" 20' 7- JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page 5/8 concrete bui the standard construction above (See unedited construction see Lab contains ten work rooms clustered around Room the room ( s room numbering system was current system shown for 4232/E-33 the one current safety rules for ion in 4232/E-33 been used for of years no longer contained process Mater s and cas were transported into storage room through s double doors on the southeast s of the building. Doors from Room 101 1 to the Liner Room to ~uw~ut and to toilet rooms on northeast s and 109 respect At a later date, Room 101 was divided two rooms, the one the building's southern corner becoming a bay with one side open to the (compare HAER photo CA-163-L-l with F .
Subsequent renovations to the building were JPL employees prepared liner formulat 1 room 11, , a bl ,two fume hoods and severa cabinets. refrac addit to l~ler1ess, the ender prepared mixtures luble additives, and mixers formula's components for the f The formulat were made 1 exposure hazards. Records were es of ormance. 104 lant would be them. th caps and other s or to cast and Casting "*' - TDI t 106 Oven 110 105 Oven II 104 L() 0\ Oven 0\ rl s:: .-1 101 (lj 1 - ..Q - I y 'lj s:: Q) t-< 0. o y 'lj t-< $]CI1 ;:oro Ul Zrt 0 -0' Cfl 'TJ OJ rt lO n PJ n . 29 (0 an of Building Liner Lab I--' 00 f-' I t-< H N 0\ >-3 JPL FACILITY Edwards Test Stat on) HAER No.
CA-163 (Page 150 Ion Baker ze 6 PVM vert mixer, f t acketed can fabricated from s ess steel al This mass t weighed about pounds and was by a 5 epower 3-phase ternat current motor (see HAER CA-163-M-4 for evations of t and its tallation plan) . 4236/E- 7 housed a 30-gallon Baker S ze 12 PVM Room 0 (see HAER photo CA-163-P-2). Two Baker were I in Room 102--a Ion capacity mode 4 PU 1 capaci model (see HAER photo CA-163 4243/E-44 ed a 5-gallon Baker-Perkins model 8-PI in t to a grain trimmer and mandrel ler. The lities of these varied somewhat, wi QrQn~es operating procedures. The Baker E 37 and 4243/E 44 are not original to earlier Bramley of The were adapted to process chemicals from commerc food process models.
manufacturers added piping for f suppression systems, and could mix and cast the of r can or "pot" was equipped at about 140 F the viscous nature of hand to small th a hopper ("tote ents under remote control. ~vuu,~t and temperature of on a mixer. Remote truments (such as and the were room at 4234/E- 5 counter-rotating stainless also ro an anetary gear to rotate SQUOY';:' t faster eared the wal s of the po ch left a JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page of pot. JPL s brief s could be the mix, thus produc the homogenous mass. A specif action is during icles of fuel and zer grind down somewhat. JPL determined that was ,s smal les fi I voids, due to the surface-to-mass rat they react more ; the action es the densi the propellant.
As might be expected, the produced propellant batches for large motors or extens series of test motors, whi smaller mixers produced batches more exper formulas, some of which required expens ents. JPL personnel also used smaller mixers I compounds as weI as f the S-gallon mixer in 4 4 IE 44 often served this purpose. Some motors were so large that several batches from the ISO-gallon mixer were to cast the ; scaled-down test versions of the solid rocket boosters NASA's "Space Shuttle" contained pounds of propel For jobs of this size, extra mix pots were from other iIi ties and batches were s them ght var buildings until suffic propellant accumulated to cast the motor.
In these cases, were no added unti the "last (see HAER photo P-4 an image of the cast a 48" motor) propellant was les per hour or a 1 proceed no ter man's t (3 1 movements system" was to set the pace & cles, for JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-16 (Page present. ives s when ac motor. had to follow f retardant es as were propel of isocyanate vapors were was provided pressurized tanks for emergency purposes. Anti-static spray solut cotton c , and wrist and leg grounding straps were for mixing any HMX Identity badges, rings, watches, pens pencils had to be removed from the persons and clothing above st as ions against anything falling into s.
were required to check out operational status of , inc vacuum pump, water pump systems, fire suppression system and equipment associated with the mixer be they began any hazardous ions. ent conditions in the room had to be 80 F 5 and 0% 10% relative humidity before propellants be introduced into the mix pot. As wi other hazardous f a of two present and all procedures were moni via closed c 4234/E 35. ents were never s to the The itself had to be sed to the ,evacuated the temperature set at 180 any moisture out a sequence specified t, the main 1 had been del head be any structure, the at low When the structure, relecl~\=u had 1 f and the next necessary, so rese sed pos second cyc JPL FACILITY Edwards Test Station) HAER No.
CA-163 (Page cyc could be as little as 5 minutes or as long as 30 HUUl~L'C~, depending on the nature of size of the batch; t for the vacuum pump to evacuate and for operators to release vacuum and lower the to to mix time each cycle s eight or ten dur the propellant, hence some batches might ~~w~,~ete. After the binder was sti ,an be , followed by aluminum powder. the size of the batch, an oxidizer (whether AP or one or two steps. If fferent types or part Ie sizes of oxidizer were called for, these were each added in separate s and the batch. The temperature of the pot J propellant was constantly monitored and recorded, as were all machine settings and mix times.
The last ingredient added was the agent (usually an isocyanate compound 1 IDPI, or isophorone di isocyanate), since that began the chemical reaction that turned the binder the a firm rubbery substance. Just prior to this step, an "end of mix" viscosi reading was taken and recorded. To accomplish s, a small sample was removed from the batch and taken to a Haake Ro sco rotary scosi meter 4234/E-35 (later moved to 4 84/E 85) A of 5 to 10 lopoises was cons 50 ki ses was too thick. Following the introduct of agent, the batch might have a "pot I anywhere from 30 minutes to 3 , all casting had to be made with the too much to be castable. sre.4/Vj) ~ Y i'U t"l trJ :os i'U PJ t"l Ii Q.J ::r:Ul ~ se.e/lPE xe, ss P.eOPELL~.N"T .FRO"!'/' J.lOl.D. Ul Zrt ". OJ rt ~ lO n PJ n ro~rtH Fig.
30 I t"l f-' H Burn as depicted in Standa ting Procedures Ol 1-3 w ~ r< JPL FACILITY Edwards Test Stat ) HAER No. CA- 63 (Page the open top. A a to the bottom of the pot, before the valve bottom of the to release propellant into motor cas motor cas itself served as the vacuum casting Bu blocks and dog bones were cas in Teflon ~coated mo , while burn rate s were to grooved mo (HFigure I H on page 13 of Scanaaro No. 0 8 sion 4 displays a burning rate strand mold; see . 31 s report.) Bulk lant were normal ... cast and cured in V2 gallon milk cartons lined with aluminum foil. Huo The casting of viscous propellants was by the installation of a pressure on top of the lant in the mix pot to the attachment of the pressure dome.
sed air could then be introduc between s plate and the , and the plate would squeeze propellant out the spensing valve on the tom of the pot the evacuated casting chamber. Casting was conducted as as was prudent, and the mix pot was sent off to be cleaned before propellant hardened. If personnel did not begin cleaning time, the job end up taking months, using acetone and tools to remove all traces of lant from the Waste propellant and the c ths used to wipe down were of as lant waste and s eventual destruction at burn unit (4249/E-50) samples were to be 4238/E~39, 4239/E-40 for The and sites housing the dif Sect Manufacture ), 16 f Ie AFB, Pasadena, :<b "'" ' , \ 102 Building Mechanical Room ow-out Panels and 101 vestibule y '-0 t"' Doors and panels removed in ::t!ro [j} Zrt o --.
en!Tj -0 OJOPiO to;P;rtH ro I t"' I-' H a; >-3 3 an of 1 Mixing & Casting JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page began as two room structures th ed Room 101 building 4233/E-34, built 196 -63 to , was 8 The xIS' with a 3-ton st for lif , motor casings and the wall of the room, including the and insulation event of an explosion (Interes and smoke roughly eastward, in winds). Adjoining the mixer room to equipment room which contained the e condit oning equipment, vacuum pumps, ion s and other equipment necessary operation. In a vestibule was built onto ~ilCa.utern wal of the mixer room and the double doors and ow-out panels moved to the new southeastern facade (see The tion provided more sheltered workspace personnel to cast large motors.
Earth-filled revet stee were constructed to the immediate t and southwest f 4233/E-34 to contain the effects of any explosions and s striking the main adminis on (4231/E-32) or the weigh and control bui (4234/E-35). In 4233/E-34 was rated for a 0 ( , 7 ) of C s 1. and f personnel. 6 2 ' 6" appearance follow the above for the des of room is the same size as the 4 33/E-34, but the overhead is 14' smaller 25 Ion Bramley was (see Fig. 3 ). ke 4233/E-34, the room contains a set of tall a blow-out wall. A 1 ton r ist Adj the room to room ch hous JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page Foundation /(dashed) ( -- " p, - " . . . . . - - . __ . _ - - I~o:-I ., I I ~I 102 I J! J ;i Building Mechanical Room 1 I~ ... .~- .,v 1 I ; i' r J Blow-out I 1 I Emergency Shower .
I ~ Panels and I ' I and Stat Doors 1 ~ 1 ,) 1 I' I oor Drain I. i 1'1 1 I I' I I I 101 Mixer Room I JI. o Chemical t Emergency Shower \ ; ., iii and Eye-wash Station J,: .!,!It Emergency Shower and Eye-wash Station 104 Mixer/Puller r-I ro rl ro 0N 1;1 I I tno Mil Room i=I'M i=I'M I 101 'M i=I '0 ro r-I..c1a 'M i=I '0 ld r-I..c1a I1"1 . -- . . - . ' 'M t> 0 'M 0 0 : I Trimmer Room "'\ Ql 0 Ql 0 I, 1 Hoist !, y 1 , "d ,I.. l' .. "';.fW~i;Z:- _~ :~ T: 'Y;~-;;~'I' L_ ow-out Wall ~ "d P! l' Ii p., ~tIl :Aim til ~rt (f) I l' \.Of--'OH . 33 an f E-44, llant Preparation JPL EDWARDS FACILITY Test Station) HAER No. CA-163 (Page took up eastern two was des for "propellant engineering drawings. A 5 machine to be ta1led, later machine. The western end of Room the building equipment room.
4236/E-37, the s of the preparat and blow-out panels nearly east; a hoist s the to assis equipment. At a later date, eo size and function by the addition of another workroom (Room a Iding equipment room (Room to the western end of original structure (see Fig. Des work was performed by Ben & Associates, Architects and Engineers of North HoI , Cali Room 103 0 but not connect internally with Room Room 104 was 20' 0" square and had a 1 , higher than Room Like Room 101 an monorail hoist was install The southern s of Room 104 incorporates an 8' wide blow-out panel, while double doors give access on the northern side. The rating posted on the building in was for a maximum of pounds Kg) of C s 1.1 s and personnel. Bui . . .
U..LCUllcter by deep cast (see HAER to CA-163-GG-3), led due to programs purposes, ace in 199 . Curing Three - 4 8/E , 42 9/E 40 and 4 40/E-41-- were ovens for cast could come from 44. On occas on motor ed JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . r ~ -_. 102 Building Mechanical Room , Insulated Door Foundation (dashed) FACILITY Test Station) HAER No, CA-163 (Page J ~, c;- Chemical Pit ./ \ I:;~ ~ --' I ' \*Bandsaw r r-I r f i i L. 1 I I I --+Milling Machine I Emergency Shower I ! and Eye-wash Station ~Ol Preparation Room ' { ' Mechanical Systems Pad 2 1 JPL .EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page cast motors and es were curing chambers and left 2 weeks at 140 F so that curing and binder had the opt t to complete ~u~u,~ca1 reaction that converted the binder into Heat was supplied by hot produced the bui mechanical room; r was exhausted from curing chamber through a wall vent with a 11 the northeastern facade; this purged the chamber of any solvent fumes from motors or drying hardware. Access to room was from the north is no tween this room and the curing chamber. entering the curing chamber had to wear flame retardant clothing and goggles. Casings and samples had to be properly supported so that no spillage occurred, and propellant scraps were not allowed to accumulate on the floor.
A recorder the kept track of the temperature, and an amber warning 1 was displayed whenever curing was performed 119 When curing was completed, further processing was necessary to prepare and tion propellants for tests. Preparation The preparat Idings-- 4241/E-42, 4242/E-4 , and 4243/E 44- as a group ed out s functions th lding 4242/E-43 as the control center. Personnel 4241/E-42 sawed, cut and lIed propellant samples to the site sizes physi tests, whereas personnel 43/E-44 worked on cast motors. In to and propellant ions, 4 43/E-44's JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA~163 (Page tools removed s from motor and trimmed and shaped the to f size.
The three were built the same solid line's development, but each are of a size and As th all the other , set up with samples lling, but actual work from a remote location Building 4242/E 43, progress closed-circuit televis and audio Iding 4241/E-42 is a x -room structure. Room 101 holds a Kalamzoo Model bandsaw with Teflon -coated saw blade, a milling machine manufac ~U~~ ~f and a workbench with electrical grounded, explosion- proof electronic s es as well as selected hand s (see The machine tools were outfitted th systems to ext sh any that might occur as the result of or lling propellants. Three types of propellant test were made here: "dog bones" (or tensile bars), burn rate strands, and spec specimens cut from bulk propellant.
Sa Rules from 19 August declare that the propellant 1 t for s room is pounds Kg) and the personne are 1 to four. As at other ldings, the f suppress (or de and other systems had to be checked out per cal The " under te contro a precise and size HAER CA-163-S 1) . bone" . The lant JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ~ r tl I ::: JPL EDWARDS FACILITY Edwards Test Station) HAER No CA-163 (Page operating unction th the waste was disposed of according to SOP~ Ie had to be made same day tion to wearing flame clo~u~Ll.~ 11 machine operator had to ground times he had to manually set the presence of propel and Burn rate s could be produced by cast them a spec mo, or they could be cut a propel block.
In the f t method, cast strands were cut to 6" length by hand using an "X-Acto ; in the latter, strands were cut to 0 3" diameter by 6" lengths with a spec round cutter mounted on the milling machine table. The mill table was by hand (see Fig. Further operations red that holes be lIed the burn strands the insert of Some samples were also coated with an inhibitor; the inhibitor was made up and heated in a bread pan for 12 es at 140 F to 180 F a small air circulating oven. operator then the strands the bread pan and coated them , or else them.
Following s was a 4 at 40 F to 160 F or a 16-hour normal cure at 140 F S were then a pan and covered with ion to the Building 4267/E-68, of propellant blocks and was accomplished by remote control ~aLll~,~es were set up by hand; the 96 feet per minute, but s var prope terist s. and a water vacuum; operators made an anti static brush. Further spec iz hand or on milling machine. In all I was splayed outside when hand process, and a red light when controll were way. Extra care was taken when HMX Extra f lters were sposed 0 as
Hmx Jpledwards Facility
Edwards Test Station) HAER No. CA-163 lPage MILLING HEAD .r---
Strand Cutter
FiGURE 2A POSiTiON PR.IOR TO CUTTING FIGURE MILL TABLE STOP PAGS140 F17 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page samples. Building 4242/E-43 is 9' 4" x concrete block structure that served as the control center for the ion bui In it were the controls for operating the machinery and warning lights at 4241/E-42 and 4243/E-44, as well as sion and audio monitoring equipment. An area rest room was luded, along with the privilege of smoking the building. Propel were not allowed in this building, but there was no res ction on the number of personnel (see Fig. Protective blast barriers were constructed in 121 Building 4243/E-44 is described above under mixing.
In addition to mixers, 4243/E-44 also contained a mandrel puller in Room 104 and a specially designed vertical lathe for trimming grain Room "The remote mandrel puller consists of a fixed structural s frame and a hydraulic cylinder mounted on this frame such that a force may be applied to remove the mandrel from the rocket motor. A hydraul power supply furnishes hydraul fluid to the pulling cylinder at pressures up to psi. An operator simply mounted a rocket motor in the frame, attached proper grounding wires and restraining hardware, engaged a cl s in the bottom of the hydraulic ram with a pin, and left the lding for the actual pulling ion.
When the procedure was competed, operators returned to remove the mandrel to storage, removed the rocket engine for further treatments, and vacuumed up any propellant dust sposal. The trimmer was a vertical lathe spec designed to turn the ends and of propel ; its manu turer has not been identified. "S manual trimming of live charges is both slow and dangerous, a machine was designed to do this operation remotely ... There are two unique features on this remote charge (1) The propellant is trimmed in a California Institute of logy, Jet Propulsion Laboratory. Barricade #3 @ E-35, Edwards Test Station, Edwards, California. March 964 ; JPL No . E3 5/8 -1 . i Institute of Techno Jet sion Laboratory, Plant of structures at JPL Plant Pasadena, JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page -Barricade co ' M M ~ I tnw ~ 0l ~ Barricade JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page vert pos t 2) propellant can trimmed to a des contour." (See HAER photo CA-163-T-1 for a view of this ; photo CA-163-T-2 shows the manually operated machine that it .) The machine could turn propellant grain from 8 11 to 14 11 in ameter, and specially contoured bore turnings could ted by a hydraulically operated template follower turning tool. A metal template shaped to the desired contour was mounted the machine, and a follower was engaged to trace its edge and adjust the cutting tool accordingly. D.
Bailey's manuscript instructions on the machine's settings indicate that it could turn a diameter charge with only inches' out-of-roundness and a taper along the 24" length. The SOP for this machine indicates that this machine was later used intensively for trimming standard BATES grains (for Ballistic And Test Evaluation System) BATES grains were cast to fit twelve-inch diameter flanged tubes made of steel in various lengths (as opposed to actual motor casings used in design tests). 124 Motors were always trimmed with the nozzle end down.
When personnel were finished with the machine for the day, all parts were washed down with acetone and Kimwipes ." The used wipes were deposited II the propellant collection drum along th all floor The was powered by explosion-proof motors and hydraulic systems. t produced waste ribbons of propellant which dropped via a chute into a VeloStat lined 30-gallon fiberboard drum. A closed c t sion camera could be mounted to ew up the waste chute and verify that cutting was proceeding on the cont appearance of a waste ribbon. A mirror was also mounted ide the machine that permitted the televis camera to an image of the cutting tool at work. The tool was operated remotely from 4242/E-43 once correct setup had been personally fied by the operators.
Conditioning ion, JPL personnel subjec motors and test speC~W~LJ.~ to long at from -40 F to F. This step was to soaking a I II ll fue the f AFB, Pasadena, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page test Is of the liquid propulsion area of ETS. Motors were exposed to different temperature ranges for to see how various propel s wi s or inactive periods outer space. be tested at various points the t cycle, and motors test fi to evaluate the effects of the treatment on the structural stability of propellants. The es and the propellant and tat were the same for each building. rules were substant ly the same as for the curing buildings, but the allowable propellant quantities were considerably higher.
Each of the conditioning structures could up to pounds Kg) of s 1.1 materials (Class 1.3 at 4245/E-46), and maximum of four could be present Iding at one t The conditioning treatments took ace in Idings 4244/E- 45 through E 49, all of which are two room structures. Room 101 is the tioning room, and Room 102 is the machine room environmental systems. Each structure subjected its contents to a specified temperature range. Bui 4244/E-45 and 49 were designated to handle conditioning (or "storage" as it is to in the ) at ent Iding 4245/E-46 operat at a 40 F to +20 o F. Buildings 4246/E-47 and 4247/E 48 o F to o F, though because of a ,4247/E-48 was for waste s Because 0 es ss some of the structure u~Hlcll~ions sl , construct Is and architecture al .
Iding 4 44/E-45 is a 6' 6" x re Coll t Jet Inst 0 , Ed'i,vards . Edwards Test Station Complex Phase Sections &: E- 33 to E-49 f / JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page concrete structure with 6' 10' steel e %" thick opening to the conditioning on southeast side (see Fig. 39) . apron to room doors was fitted with a steel grate for c The mechanical room doors open on the northwest machinery inside supplied movement into room and out through a vent over the condi '--LVU-L~l.',;j Building 4245/E-46 s a x concrete bl structure. A single x 10' 6" insulated s door opened into Room 101 from the southeast side, while Room 102 was from the northeast side of the building (see Fig.
Not were the walls of Room 101 heavily insulated, but the floor structure was honeycombed wi air ducts to promote thorough, even heat of the room (see HAER photo CA-163 II-1 for a photo of 4245/E-46 when floor was under construction). Hot air was supplied from Room 102 through underground 12" diameter Transite (pressed asbestos) ducts, from which branched diameter copper pipes that conducted air from the 12" ducts to the spaces under the oor. The rooms in 4245/E-46 were of nearly equal Slze. Buildings 4246/E-47, 4247/E-48 and 4248/E-49 were each 4" x 24' 0" concrete bl structures in which Room 101 enclosed over twice the floor are of Room 10 (see Fig. 4 ).
Each condit room had 8" of f and finished Cali Institute f , Jet Propulsion Laboratory, Plant Engineering, Propellant Storage Magazine, Floor Plan Sectls & Elev1s, no JPL . No. E45/l O. California Institute of Technology, Jet sion tory, Plant Engineering: engineering o structures at JPL Edwards Facili Drawings on JPL Plant asaClelna, California. Aus Street, e Techno , Edwards Mechanical E-46 JPL EDWARDS FACILITY Test Stat on) HAER No. CA-163 (Page -~~ ~J j iL.J 102 101 Building Mechanical Conditioning Room Room Systems Pad 9 44 4 f JPL EDWARDS FACILITY Edwa~ds Test Station) HAER No. CA-163 (Page Feeder Ducts /~ -. /' _. --~ l j . ='l . ~r I I I ' .' I . I I I I I 102 I I [I , I !1 101 Conditioning Room I~\ I . Insulated Door I Building j I Mechanical I J R I J I ,oom I "L- d I - 7 ..
- ., J I lFoundation ~ Underground (Qashed) Hot Air Duct Fig. 40 Plan of Building 4245/E-46, Propellant Conditioning JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ~8" Insulation 101 Conditioning \ Room -Insulated Door I -Asbestos . 41 E-47 9, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page of 3 16 n cement tos board. 4246/E 47 and 4247/E 48 were 1t with hot water boiler units. Later, e units were removed, and electric -rods n substituted heat sources. The roof of 4247/E-48 during a conditi cycle; to Robert Ray, the occurred ter working and burned for a long time ~c~uu~e the facility could not see it from his guardhouse. Sterilization At one time, NASA programs called an extreme conditioning process solid propulsion motors.
NASA ordered heat sterilization of spacecraft destined to on planets in order to ensure the spacecraft could introduce no ion to an ien world. NASA specif ions a motor for a Viking (Mars) t to withstand seven cycles 54 hours long at 275 0 for propellant type approval and f 54 hour cycles at 257 F for flight approval An autoclave in Building 4272/E-73 subjected JPL Aus ld & TilJest Third Street, Los les 57, l n Edwards Test Station Complex- Phase II, Jet Propuls California Institute of Techno Force Base, , Cal ; Magazine: Floor Plan, Elevations, Section & Schedules for E-47, E-48, E-49, A-46, 26 June JPL . No. E47/1-0. Cali f ogy, t JPL Pasadena, JPL.EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page motors of 275 F to develop propellant withstand this st lization process required characteristics. At these , JPL looked loss of lant ~HC~.LU~, and chemical decomposition of the ion. ial treatments were sterilization tests, motor were internal faults. JPL ,recrys lizing and orate with a phosphate dopant (ammonium phosphate monobasic, NH 4 H2 P0 4 ) made the oxidizer much more stable at high temperatures; use of unsaturated polYillers such as polybutadienes as binders made for stable, dependable binders. One particular propellant formulation survived 17 sterilization cycles and f successfully, demonstrating the propellant formula loped for it was more than up to NASA's for the program.
The Safe Rules Building 4272/E 73 11 it as an Environmental Conditioning Building limited to pounds Kg) of s 1 1 propellants and personnel; it could ect prope lant and motors to 90 F to o F us a autoclave. It was built of reinforced concrete ock measures x engineer 1 "s lization Facili "and the Real the "Sterilization Laboratory." autoclave, using gloves whenever Flame retardant cloGu~u.~ had Temperatures Ie t upon t program requirements (see Fig. Physical Properties Tests JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page I I 1 I N 0 ri mRS s:: 0 ~S::O r-iRSO ::3 0 CD ! I ~ I I 1 I I I Autoclave! I I 1- -1 II I I I I I I I I L- _ _ _ I I L __ J 101 Future Oven 4 4 z JPL EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 4267/E-68, 1 tests correct s i n g the ts up to I-size motors; is " ... not a 1 process." Tests made at Test Stand "G" ion Facili) Test Stand "E" were necessari of motors, so correction tors were unneeded there. Non-combustion Tests 4234/E-35 is discussed above; Building 4282/E- Services Facili , was constructed in as a x two-room concrete block structure. It was almost immediately enlarged to a x structure containing seven rooms (see F . Room 101 was dedicated to instrument cal ion, Room 102 to instrument repair, Room 103 to Room 05 was designated a clean room, and Room 06 as the sing room access to the clean room; Rooms 105 and 106 were the original structure.
Room 106 was a chemical a storage area designated as Room The balance of rooms to were for a lavatory, jani closet, and vestibule. Two exterior "bottle s " areas were tructed on eastern Viscosity Tests The SOP for use f the Haake Ro scomet indicates that must wear coveralls, sa ses and gloves lants and ensure that 1 s proper i transported from to the scometer a stainless steel s ide an VeloStat 1 scometer cup is fi approximately 10 grams of Robert ew Cali of Technology, Jet Propulsion Facilit truct f Addition Technical E.T.S. Plan, Schedules Details, E8 Cali Inst / ,.
__ A 1); 103 $ Transducer 101 102 Calibr(ltion I Instrument Instrument Calibration Repair ,-\ J, I Bottle Storage L_ ( industrial 1 Fume gas cylinders) I Hood II I 106 / cfu -l Fume '~ Hood Chemical Clean Room Laboratory / ~ C-4 tlj L' trl 1-' o..C-4 :s tlj Pl L' ti o..trl g;en~ I en tJ ~ - - - - - Original Building -- - - - Addition 1 0 \J. PJ <'oOPlO (J)'"Ij ro rt H N I L' f-IOH WOl::Jt-3 Fig. 43 w~~ Plan of Building 4282/E-83, Technical Services Facility JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page it is inserted under a rotor; excess propellant 4284/E-85.
If the propellant s still at ( a F to 140 F, depending on propel formula), the test can begin immediate ; otherwise operators must wait until the scometer bath the propellant up to s measurement cycle takes 20 minutes. For c ean-up, rotor and are removed from the scometer and the propellant s emptied into a waste container. Using rubber clean the cup and rotor wi a spatula acetone- or cyclohexanone soaked disposable towels. Used towels are disposed of in the same container as waste lant. Tensile Tests The Instron machine is ce which will chart the elongat of a prope lant in response to the duration of the test and the tens applied to it. 136 The machine also has a ti chamber which can subject the sample to from F to ambient during the tests.
Liquid was A tensile test could last several hours." bones" were tested until they broke, and then the could be packed for scrap or stored for s on the 1ant engineer's shes Peel Tests The scussed above was also pee test s of the bond between a propellant and ion a climbing peel test attachment. made peel tests by cutt e a 17 has been crossed out JPL .EDWARDS FACILITY Edwards Test Stat ) HAER No. CA-163 (Page 6" x 6" squares of insulation. leaned the ion with acetone and at least one hour at 140 F. The insulat to molds using tape with adhes on both s an layer of liner compound to the insulation using a trowel. The molds were then baked 24 hours at 140 F.
After operators transported the molds to a mixer and vacuum of propel over the 1 When the combination was , the propellant/liner/insulation sandwich was lled to %" thickness on the milling machine in 4243/E 44 and cut into strips 1" wide. Each mold produced a sandwich from which four 1" s could be cut. The propellant sides of three of these strips were bonded to sandblasted aluminum strips and the fourth strip used for visual inspection. For each test, operators talled a strip in the test apparatus (see Fig.
measured the width of each strip to the nearest and recorded the force required to peel the sample apart at W' per minute In addition to recording the visual appearance of each peeled sample, operators derived the peel strength with a formula, using data from the machine and the strips. Disposal of tested samples s not discussed the SOP for s operation. Specific Gravity Tests Measurements of a propellant's specific (ratio 0 propellant density to the density of water) were made with a I Quantachrome S Personnel f re-retardant lothing and rubber when handl x 1" 1" lant samples requ tes . used a spec cell from the s ter, care weighed with and without a e. The cell was talled in machine, and an inert gas was at a recorded pressure. Operators measured the gas volume and the propellant density.
Tested es were shipped 4247/E-48 disposal as waste and the cel learlea acetone. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page STRAP HUNG ON HARDENED PIN ALUMINUM STRAP~~t--_-rt~:;::!mlli BONDED TO PEEL SAMPLE INSULATION CLAMPED TO BARREL SECTlON Fig. 44 Diagram of Peel Test As Performed on Intron Machine JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 {Page Combustion Tests vw~uot test of propellant samples occurred Bui 4267/E 68, ter ; the bui 's Sa Rules re to s structure as "Igniter Laboratory and Small :f\1otor Assembly." s 4' -0" x 25' 8" concrete block structure two rooms an exterior test bay (see F 4) Room 10 was where some tests were set up and ters and small motors assembled.
Room 102 was the bay where hazardous tests were conducted; all tests in this bay were remote controlled from Room 01. Room 103 was simply the building mechanical systems room. Room 101 was limi to 20 pounds (9 Kg) of Class 1.1 s and four personnel, whereas Room 102 was allowed up to 80 pounds (36 Kg) of Class 1.1 materials but only two personnel. Flame clothing and safety goggles were required attire, and personnel handling explosive materials were also required to wear grounded wrist straps to dissipate any stat elec cal charges Grounding bars were located at the entrance to Room 101 for personnel to touch upon entry. JPL test engineer L.
reI JPL staff and prepared many types of igniters at the Igniter (4267/E-68) instead of purchas them from commerc These "homemade" devices were tested pieces of up the test test bay was also the site of checks and tes firings electr squibs and ces Most ters consisted of boron s )], al [AI( [B( )] were also used. Raw materials well as assembled igniters themselves were L Lu~u.~ine, 4261/E-62. Burn Rate Tests rate tests s 1.1 and .3 propellants were made trument cal "Crawford Bomb, " cons s 0 tell a er bath. JPLEDWARDS FACILITY Edwards Test Station) / HAER No. CA- 63 ~ {Page s_ Emergency Shower and Eye-wash Station '- Fume Hood Concrete .: Apron '7" ;., 102 Test Bay 103 Building Mechanical Room - 8! JPL .EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page 6" strands of Tests were conducted at pressures rang from per square inch absolute (ps Class up to ps s 1.1 s on parameters requested. Dif f rates depending upon the ambient pressure; of these factors was important for and ~~.~.~~u, S lants in an actual motor le under pressure producing thrust. The pressure bomb was al by introducing GN 2 from pressure 1 serving JPL Edwards. The temperature be from -50 F to o F. Crawford bomb was a Model 535 At Research Corporation. strands were prepared for the tests by drilling a le an tion , and two more holes 5" The timing wires indicated when the In the strand pas the measured points along the strand.
trurnents were connected to the Crawford bomb, including pressure gauges, pressure transducers, a plotter, and various remotely controlled valves. Burn rates could be moni the pressure transducers or acoustic emiss equipment; in first case, all strands were fi s taneously whereas the second, only one strand was fred at a time. Each test took approximately 30 seconds. When tests were completed, high pressure gas was bled from the bomb, and the t lowed to coo be it was and res cl=u,u,~~ out. X-Ray (psia) is of zero are pounds per square the gauge is equal to JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page lures parts of the cas or zz e were immediate table. I a motor to be X- with the motor rotated ong its vertical s to a ipal orientation.
After the t X-ray was made the motor was rotated 90 about its vert s a second image made. This the detection of most faults. were also made th the motors other posit Motors X- during condit ! be and after tes at the Facili (Test Stand 4271/E-72) and other of motor production. Building 4286/E-87 was a x concrete block structure built in to accommodate a 1 Ilion tron volt X-ray machine purchased from the Lockheed ft Corporation. This unit was considerably more powerful than the one used at Test Stand "E" (4259/E-60). It was housed in the 26' tall "high bay" of the ility, which was separated by a 4' thick concrete shielding wall from the "low bay" where the control room and film processing room were ocated (see Fig.
46) The high bay contained a travell bridge crane from which was suspended a scissors and form for the X-ray unit. This ted to set the X- ray unit in a wide positions. A 14' wide by 18' high roll-up door in the northwest facade of the gave trucks access to the building for mo del and Due to facili was of land to and a zone was northwestern boundary of Facili so that the elding wall was between the the entire JPL Edwards Fac Ii enclosure to closed to the iIi image was made, and swi on a red the od X- rays were tted, an r at s. exposed, ray ilm was film processing ~HUll,~~~ate Further could be made JPLEDWARDS FACILITY Edwards Test Station) HAER No, CA-163 (Page I II ' .. 103 I X-Ray Bay IJ 1 1 t . '.
102 101 Dark Room Control Room /' c i JPL EDWARDS FACILITY Test Station) HAER No CA-163 (Page the spot f necessary to c questions. From 4286/E 87 a motor could be returned to the process s it had 1 to test ion, or to Test Stand "G" or Test Stand "E". Motor Assembly to ion tests or test firings, JPL personnel assembled inert of motors in Building 4260/E 61, des the "Inert Assembly lding." It contained an office, area rest room, a small machine shop, and X-ray film processing facilities used when were conduc at Test Stand "E" This 8" x concrete block structure was built in as part of the JPL solid line's first wave of construction. It was connec to tunnel system an outs entrance (see Fig. Small s were made as necessary for the assembly of parts.
No propellants were ever admitted to s structure. The f assembly of I motors was carried out 4268/E 69, We & Tes s x 39' 0" concrete block structure consisted of two rooms: work room containing a I hoist, ontal steel , and a pound capacity floor s e, and a room (see Fig. The work room was rat pounds Kg) of Class 1. mater Apparent no structural ficat were lding since its construction, , a i 1 was taIled sometime before to ean-up the recovery of contaminated so No more than one motor could be processed at a t had to lec grounded whenever it was one metal f to another. Personnel wore flame tion, wrist and leg handled s of I motors (see HAER I and Tes I JPLEDWARDS FACILITY Edwards Test Station) !W HAER No. CA-163 (Page I . '. 101 Assembly Room 105 Office '. Fig.
47 Plan of Building 4260jE-61, Inert Assembly Building JPL EDWARDS FACILITY Edwards Test Station) I HAER No. CA-163 ~. (Page an 0 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page of BATES motors) . Any scrap t-minute trimming and fitting could not ~~UU'~~f nor could it s overnight on the Personnel to required s and Next, they assembled motor taIled boron wafer igniters, installed the wrappers) in the casing, and then a t '-~''-uc<-< out ined for assembling some motors ( BATES motor) were applicable to assembly at as well as at 4268/E-69. Assembled motors were stored on three-wheeled "bomb carts" in Building 4268/E-49 wi Ve on the nozzle openings until needed tests. The lding 4261/E-62, is a x 8" steel a flat blow-off roof constructed from 2" x 6" ters and W' thick plywood.
It contains two rooms labeled l-A and I-B, each with two outward- opening, steel doors. The first exterior door opens to a small vest , which itself has a steel door leading into the space proper. By the handle of each exterior is a steel th a visible grounding cable and a s "Caution: Grounding Bar - Touch Before Entering" (see HAER photo CA-16 -AA- ). All wiring ec light passes through mounted s conduit to minimize the ri of explosion init malfunctioning wiring. The magaz was ly constructed 63 as a one-room 6'- 8" x structure 8" concrete walls (Room I-A). Room I-B was a three-room was 12" thick walls, reflecting a for the construction of bui Fig. The building is posted for .) of s 1.1 s. Each a cabinet in whi ters, 146 -90-E69-5 f s 5 September # Motors, 9.
Records Center, Collection, / s_ Grounded Steel Doors I ' - - I i.' I I I ~ 1\ y 'U I ./J I t" trl L ~ 'U PJ t" Ii ~Ul~ ~ ~ ~ built~ .~ .~ ~- ~ original~ ;:dro;:d Ul t:J - - - Never - Addition-.+ -0. Cf) 'Tj ~ rt :J;I (t) nPJ n N I l - " t" Nt->OH Fig. 49 ~ 0'\ ~ >-3 Plan of Building 4261/E-62, Igniter Magazine JPL FACILITY Edwards Test Station) HAER No. CA-163 (Page electri ces or their constituent chemi s were drawers. JPL personnel had to wear flame retardant clothing when and carry igniters in metal to ze the poss Ii the might be "touched off" by ion. Test Stand Vibrator Because spacecraft sol motors rode larger rockets into earth orbit or beyond, their motors were subjected to considerable vibration during launch.
JPL s f built Test Stand "G" 4271/E-72 in to determine motors' ability to thstand launch conditions by simulation Building 4271/E-72 was a x concrete block structure with three rooms; the vibrator was installed a 26' tall high bay, while the equipment room and amplifier room were I the low bay (see Fig. 50) The vibrator itself (see HAER photo CA-163-EE-2) was " ... a MB-C210E Electrodynamic Exciter having a maximum sinusoidal force output of . and a no-load-peak acceleration sine wave of 80 gs" gs" means 80 times the of gravity) . The was connected to a steel table on which motor assembl could along with associated instruments (see HAER to CA-163-EE-3).
Because live motors were tested here, the east elevation of the vibrator room was equipped with blow-out panels blow-out 10' x 26' double doors. Personnel were no allowed inside the building 148 ley, IJr,r-ncol Section Records on file in temporary storage, Research Center, Edwards AFB, California, part Collection, Pasadena, l 149 Cali Insti tute of Technology, Jet Propulsion Laboratory, Plant Engineering, Vibration Test Facility E-72, Floor and Roof Plans, Sections, Details Door Schedule, Sheet AI, 21 May JPL No. E72/2-5; i Institute of Technology, Jet s on , Plant , Vibration Test Facility E-72, Exterior Elevations, A2, 1 May JPL . No. E7 ti Technology, Jet ion of structures at JPL Plant s_ 111IlC!I/!!.1I illlli.h'llilffr" _ IJeIf L . . . 1,1 , , I' _ ... ... I . .. J ., I.. If. I '..
Amplifier ect ca Room ,-QJ,J.J.UC;;",S ~ tilt ~r ...,.'V----r---Ud.:.... ~ l I , Vibrator :- ,II rL:i ~ ~. -i-:-t.....""e-- M01!0rail HOlst y Vibrator Pad co Mech. _____:u.:.- t-t Room Q;y ... ;. .. fxJ .# ~ cot-t 1-1 Q; ~Ul Ul Zrt Cfl rt~ OPJO I 1-" t-t f-IOH ffit:l>-3 ~~ 50 an Sui 42 E- 2 Test St "G" (Vibrator) JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page tests l and not re-enter t until 15 ter a testIs conc ion. In 1 new catwa tal led on the north and south walls f the or to the building In JPL converted 1 facility to an Autoclave & ion Facili A new 5' x 8' autoclave was purchased to NASA programs I 4271/E-72 had the e power supply to support autoclave.
As part justification conversion, JPL Edwards staff said that the vibrator had not been us 15 years, and there were no plans for its use. autoclave rubber insulation materials at tures up to 400 F and pressures up to 400 pounds per square inch. Normal to be cured were placed in vacuum and lef under Hg vacuum. Inst tute Techno t Jet Plant IVibration Test Facility E-72, Floor and Roof Plans, Sections, Details & Door Schedule, tAlI 21 May i a Institut of Jet Propulsion of structures at JPL Plant ..LU..Lll,'::::!;::'! II a at JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA~163 (Page s , pressure and gas were applied as by a process Contents of the autoclave had to cool below 200 autoclave could be shut down. The s of oxygen and CO 2 were ly moni ide and outside the autoclave.
Iding were oxygen levels inside building 1 below vented from the autoclave. Test Stand "E" Test Stand "E," built in is a 5' x 70' s poured concrete structure with a four The test stand consists of two individual atmospheric, (one vertical and one horizontal) solid-propellant rocket motor f Is, and trumentation room, and a third test cell as an on cell until (see Fig. 19, page The two rocket motor cells are located on the north half of the test stand, and the inspection cell is on the south half of the test s The north bay is open on the east facade; it contains a metal work bench and a 2-ton steel I-beam monorail hoist. A remote camera is trained on the work bench. A metal covers the bay. The acent south bay has tall concrete walls and an upper divider for separating and tests.
It has a metal roof, and is open on the east facade. The center bay was used and zontal rocket motor f An octagonal iedown is on the ground. Openings west walls convey trumentat and utili es system. These test cells normal motors rect, t reverse. Maximum was JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page attached to the west facade of the south bay. It housed a generator and monitor; a door on the south facade of the addition accessed equipment. Two fully enclosed wooden plank blast barriers (native soil and cribbing) are located on the north and south facades Test Stand "E." The north blast barrier been extended and in a metal Test Stand "E" was f t NASA's commerc satellite and spaceflight program, such as Syncom and ATS.
Solid-propellant kick motors, to place Syncom and ATS in geosynchronous (geostationary) orbit around the earth, were tested at Test Stand "E" in the Nozzles a pound solid-propellant motor, under development space shuttle program, were tested on Test Stand "E" the late 156 The two test c Is were modif to accommodate testing of 48 inch motors for the space program. In later years, propellant configurations the ASRM was tested at Test Stand "E." The last test firing at Test Stand "E" was conducted in April Waste Disposal and Clean-Up The accumulation of scrap , used propellant samples, and propellant wastes and solvents was stored at two sites on JPL 4247/E-48 and 4258/E-59. Eventually, accumulat be disposed of, and the JPL solution was to burn t. Is were cleaned by contractor.
The inc 4249/E-50 was original a propane-f waste materials (see HAER , Kern County waste changed open pit burning of of waste. The 4249/E-50 propellant wastes were kept in sealed and placed a chute which led to the A maximum of 50 pounds (23 Kg) propel could anyone Loading the was to be the 4249/E-50 , however, loose ) be Ions of solvent the east 0 the to teel be could JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page be at one t ,and whenever burns were underway, personnel had to be behind the barricade, and all and brush a 100 had to be cleared from t burning was sanctioned, burns were conducted had the time to do it.
Kern County es at least every 90 days to prevent a hazardous f eSt but JPL personnel preferred to wait until at least 00 or 300 pounds of waste had accumulated be disposing of t. s minimum quantity assured that all waste would be burned up. A maximum of pounds was permitted during a s e burn. 157 Facility Administration wi the construct the f t phase of the sol propellant line JPL also constructed an Administration Building 32 (see Fig. The administration and communications wing was constructed first with expans anticipated. The initial wing was a 40' x 80' structure which provided only offices and a room telephone The second phase, call ,.
support " for E-32 were designed by Aust f ,Field & and constructed the Army Corps of Engineers in These iIi es provided numerous amenities in addition to more off space. Inc were a conference room, , a machine shop, and a total floor area several t The internal connect between awkward for personnel, the two of two opposed corners. followed hard on the addition provided a Iding and added still more original included a vert 14" engine lathe, a and heat treatment oven (see were of any of spec ized operat - . I r Original wing '\ '- . \ Modifications $_ I I I I I . . . . . ~ . ~ I I I I I I y Modifications 'U I t:' I trJ Q,y I ~ 'U ~ t:' \ t-i \ " _-- - - - - - -Support facilities - - - ~~ o. (f) -0 rt ~ ~ n ~ n (l) I Fig.
51 Nf-'OH W O\::l 8 Plan of Building 4231/E 32, Administration Building & Shops w ~ r< JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-l (Page The strat and its support iIi es are e structure at JPL Faci ty where any tec "flavor" appears, even here, it is reserved the publ entrance on south s of the original wing. The rest of the facades are built of reinforced concrete block , rigorously functional design charac s I buildings. JPL eDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page ) Chemical Names and Formulas Ammonium Ammonium Ammonium sulfate: (NH Boron potassium nitrate: 3 )2 Carbon dioxide. CO 2 DOA (di-oetyl adipate): CH 3 (CH 2 ) ] 2 ( Gaseous He HJI.1X (eye tramine) : IPDI (.1.C>v""uv di-isoeyanate) 1 ): JPL,EDWARDS FACILITY Edwards Test Station) HAER No.
CA-163 (Page TDI OC~farlal:,e) : TNT trotoluene) : Triethylaluminum Al( [B ( Water: EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page PROJECT INFORMATION s HAER report had its genesis Phase II cultural resource evaluation of the Jet Propulsion Laboratory Edwards Facility conducted by Scott M. Hudlow, Architectural storian, Environmental Services Department, Appl Technology sion, Computer Sciences Corporation, Edwards Force Base, California. The Phase II study determined that the JPL Fac i was el as a National Register of His s distr , and that the Air Force Flight Test Center closure plans resulted in adverse effects which merited mitigatory HABS/HAER documentation under Sections 106 and 110 of the National s Act.
This addendum was prepared to document id propellant manufacturing and testing line, since this portion of the ility has great historic significance its own , was litt used, and personnel who could be for were retiring. At the time of this writing, there are few people nationwide training in the art solid propellant development, hence there was an additional urgency to document the solid propellant line while personnel knowledgeable its history and operations were available to assist in the documentation. The historical background and sources from Mr. Hudlow's work were adapted Richard K. Anderson, Jr. to meet the HAER report format and HABS/HAER standards as required by the Phase III cultural resource documentation ect conducted by Mr. Hudlow. Mr.
Anderson also included in the report numerous and s observations derived from reviews of historic drawings, JPL photographic site sits to the lant , and telephone and th JPL Photocopied from the JPL of test stand schemat and drawings have been filed along with several dozen Hudlow 9 of JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 tPage mission. In t to the HP R , Mr. Anderson prepared two HAER measured drawings, collaborated with Mr. Hudlow in selecting sites HAER photographic documentation as well as photographic of photographs and drawings for inc the HAER Grogan and Philipp S. ttermann, Photography A s s o c , Inc., Yosemite, California made contemporary format photographs.
storical JPL negat were photographically copied by Bob Schlosser of the Huntington , San Marino, California, with the invaluable help of David Deats at the JPL Photographic Laboratory in Pasadena, Cali The HAER report, measured drawings and large format photography were prepared under Computer Sciences Corporation purchase order No. 7 July Richard K. Anderson, Jr , vendor. Hudlow and Anderson apprec the numerous hours of assistance given by JPL employees William C. Tibbitts Edwards Facility Manager), Bob Ray I Test ), John Bluth Archivist, Pasadena) and others in pointing out f es, investigating lit questions and reviewing the HAER documentation at of its preparation.
Primary and Secondary Research research for the Phase III HAER report on line was conducted between December photographs and as-built , were reviewed at the JPL Edwards Facili closure, the records were transferred to the , Pasadena, California during review. were placed in long-term storage Center at Edwards AFB, Cali a in were made to Scott M. Hudlow November thanks to John Bluth records, ect made JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (P~ge reports, and newspaper. JPL most quintessential historic information germane to the Facili Force Flight Test Center History Office (AFFTC/HO) sparse documentation pertaining to the JPL Edwards Faci Because JPL was a non-Air Force tenant organization, AFFTC/HO not historic records.
The AFFTC/HO did, however, some useful historic Army reports which discussed The library proved useful for locating secondary sources on JPL and the space program. Off libraries and repos were contacted and/or visited to complete the ect. Beale Memorial Library (the main branch of the Kern County Library) in Bakersfield, California, was contacted and sited and Walter W. Library at Cali State ity, Bakersfield was visited. Secondary sources on JPL and the space program were located at both libraries. JPLEDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page
Figure Sources
Notes: Building illustrated in s ted of JPL engineering symbology and annotations have been each structure's plan more drawings used in this process are notes for reference. the used for are products of several "generations" of reproduct should not be regarded as scale tably, have been introduced. Line quali significantly on some drawings. In the interest of clarity, were "touched up" the HAER llustrat ,but not redrawn due to time limitations . 21 Left: t for Buildings 4232/E-33 through 4248/E-49 taken from: Austin Field & Architects Engineers West Third Street, Los Angeles 57, Cali .
"Edwards Test Stat Complex-Phase II, Jet Propulsion Laboratory, Cali Institute of Technology, Edwards Force Base, Edwards, California: Typical Structural Sections & Details E33 to E49, Sheet S 2, 26 June JPL No. E33/8-0. Right: ColI taken from: California of Propuls Facili and Construct Of f Addition to E-37, utilities Plan, 25 June 25 Feb JPL . No. E37/9 1. Fig. 22 Jet Propuls fCal Institute of Force Base, Edwards, Typical Service Panel. ; JPL . No. E33/18-0. . 2 June 982 , Jet s , Building No. E-70, Site Plan, Floor Plan, Elevations and Details, 2 June 962 . No 0/ JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . 2 Field & , tects Engineers West Street, Los Angeles 57, California.
"Edwards Test , Jet Propulsion Laboratory, California Ins tute of Technology, Edwards Air Force Base, Edwards, California: E-36, Grinder Plans, Elevations, Sections Details, Sheet A-37 (6 of 26 June JPL . No. E36/ -0 . 26 i Institute of Technology, Jet Propulsion Laboratory, Facilities Engineering and Construction Office, Propellant Processing Building E-84: FIr. Plan, Elevations & Sections. Sheet AI, 3 June JPL No. E84/3-0. 7 Austin Field & Architects Engineers West Street, Los Angeles 57, California. "Edwards Test Station Complex--Phase II, Jet Propulsion Laboratory, California Institute of Technology, Edwards Force Base, Edwards, California: Dryer Building: Plans, Elevations, Section, Details, Door and Finish Schedules, Sheet A-39, 26 June JPL No. E38/1-0 .
28 Cali Institute of Technology, Jet Propuls Laboratory, Facili Engineering and Construction Of ,Addition to Weigh & Control E-35, Demolition, Floor & Roof Plans, Sheet A-2, 3 Oct. 198 JPL . No. E35/3-0. 9 Engineers West California. "Edwards Test Stat Phase II, Jet Propulsion Laboratory, Cali Institute of Technology, Edwards Air Force Base, Edwards, i Liner Laboratory: Floor Plan and Schedules, Sheet A-31, 26 June JPL No. E3 /4- o 8, p. 1 Procedure No 20 Cured lant o EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . 3 & ,Architects West Street, Los Angeles 57, California.
"Edwards Test Phase II, Jet Propuls Laboratory, Cali Ins itute of Technology, Edwards Air Force Base, Edwards, California: Casting Building Plans, Elevations, Section, Details, Finish and Door Schedule, Sheet A-34A, 26 Oct. JPL No. E34/3 O. Fig. 33 Austin Field & ,tects West Third Street, Los Angeles 57, California. "Edwards Test Station Complex--Phase II, Jet Propulsion Laboratory, California Ins tute of Technology, Edwards Air Force Base, Edwards, California: Mixer Building: Plan, Elevations, Section, Details, Finish and Door Schedule, Sheet A-38, 26 June JPL . No. E37/1 O. . 34 Austin Field & tects West Third Street, Los Angeles 57, Cali "Edwards Test Station Complex- II, Jet Laboratory, California Institute of Technology, Edwards Force Base, Edwards, ifornia: Remote Prep.
Plans, Elevations, Section, Details, Finish and Door Schedule, Sheet A-43, 26 June JPL No. E44/1-0. (Original lding) Ben Beckler & tects & Engineers North Hollywood, Cali Cali Ins itute of Technology, Jet Laboratory, Faci and Construction , Addition to Building E-44, Floor Plan, Elevations & Section Sheet A-16, no date; JPL No. E-44/6-0. 5 Aust Field & Architects Third Street, Los 57, Cali Station Complex--Phase I, Jet California Ins tute of , Force Base, Edwards, Cure Building: Plans, Elevations, Section, Details, and Door Schedules, A-40, 6 No. E39/ -0. General arrangemen JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . 36 Austin Field & Architects Engineers West Third Street, Los Angeles 57, California.
"Edwards Test Station Complex--Phase II, Jet Propulsion Laboratory, California Institute of Technology, Edwards Force Base, Edwards, California: Preparation Building: Plans, Elevations, Section, Details, Finish and Door Schedule, A-41, 26 June JPL No. E42/1-0. . 37 J. A. Barry. Standard Operating Procedure No. sion 4. Preparation of Cured Propellant Burn Rate Strands. 8 March Figure 2, p. 14 of 17. Fig. 38 Austin Field & Architects Engineers West Third Street, Los Angeles 57, California. "Edwards Test Station Complex--Phase II, Jet Propulsion Laboratory, Cali Institute of Technology, Edwards Force Base, Edwards, California: Control Building: Plans, Elevations, Section, Details, Finish and Door Schedule, Sheet A-42, 26 June JPL No. E43/1-0. .
39 ifornia Institute of Technology, Jet Propulsion Laboratory, Plant Engineering, Propellant Storage Magazine, Floor Plan Sect's & Elev's no date; JPL No. E45/1-0. . 40 Aust & Architects Engineers West Third Street, Los Angeles 57, California. "Edwards Test ~~a~.~on Complex--Phase II, Jet Propulsion fornia Ins tute of Technology, Edwards Force Base, Edwards, California: Magazine: Plans, Elevations, Section, Details, Finish and Door Schedule, Sheet A-44, 26 June JPL No. E46/1-0. 41 Aus Field & Architects Engineers West Third Street, Los Angeles 57, California. "Edwards Test Complex- II, Jet Propulsion Laboratory, Cali~v~Ll~Q Ins tute of Technology, Edwards Air Force Base, I : Magazine: Floor Plan, Elevations, Section Schedules, . A-46, 26 June 196 JPL No. E47/1 O.
tute of Technology, Jet sion , Plant Engineering, Sterilization Facility E-73, Mechanical Site Plan, Piping A!e Plans, & JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . 43 California Institute of , Jet Propulsion Laboratory, Facili and Construction Office, Addition to Technical Services Facility E-83, E.T.S. Floor Plan, Schedules and Details, Sheet A-2, 19 June JPL No. E83/ 5. Fig. 44 L. R. Shirai Standard Procedure No. Manufacture and Peel Test of Propellant/Liner/ Insulation (PLI) Interface Test Samples. 7 February 4, p. 10 of 18. Fig. 45 California Institute of Technology, Jet Propul on Laboratory, Plant Engineering, Building No. E-68, Site Plan, Floor Plan, Elevations and Details, 2 June JPL No. E68/4-1.
46 Ben Beckler & Associates Architects & Engineers Lankershim North Hollywood, California Cali Ins tute of Technology, Jet sion Laboratory, Facilities Engineering and Construction Office, Radiographic Inspection Facility, Floor Plan, Sections & Elevations Sheet A, 25 June JPL No. E87/4-0. 47 California Institute Jet Propuls t Laboratory, Plant , Assembly E-61 Floor Plan Foundation, no date; JPL No. E61/2 O. 48 Kistner Wright & tect & , Los Angeles i E-59, Site Plan, FLoor Plan, Elevations and Details; Design and Construction of Oxidizer Remote Process & Igniter Edwards Test station, Edwards, California. A 3, 12 Dec. JPL No. E69/3-0.
49 s to Building E- 52, 12 Dec o Institute of Techno I s Plant I Vibration Test Facility E-72, Floor and Roof Plans, Sections, Details & Door Schedule, Sheet 9 ; JPL . No. / - JPL .EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page . 51 Ins tute of Technology, Jet Propulsion , Plant , Administration Communications Wing, Building E-32, Floor Plan, Schedules, Abbreviations & Symbols, A, 1 November JPL No. E32/4-3. Austin & tects Engineers West Third Street, Los 57, California. "Edwards Test Station, Jet , California Institute of Technology, Edwards Air Force Base, Edwards, California: Supporting Facilities E-32 Part Floor Plan West Portion, Sheet A-5, 6 of 35, 26 February JPL No. E32/12 1.
California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering, E-32 - Modifications Site Plan Details, Sheet C, 26 September JPL No. E32/46-1 California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering, E-32 - Modifications Floor Plan West Portion, Sheet Al 26 September JPL No. E32/47-1 JPL.EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page BIBLIOGRAPHY PIUMARY
SOURCES
2433 words
The headings the report itself prints. Each one jumps to where it begins.
Source document
Quoted word for word from HAER CAL,15-BORON.V,1-.
Not written, edited or summarised by this site.
A. Facility Records "Real Property Record - Buildings," a series of cards on each structure at JPL Edwards Facility, recording construction, alterations and costs. Records on file at JPL Edwards Facility, Edwards AFB, California. B. Maps and Drawings California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Edwards Facility, Edwards AFB, California. Schematics and drawings from test stand files of David Quarles and John Richard Bonner, JPL test engineers. Schematics and drawings on file at JPL Edwards Facility, Edwards AFB, California. C.
Historical Photographs A large collection estimated at images was reviewed at JPL Edwards Facility in Original negatives are retained by JPL at its Pasadena, California headquarters as series 11, and Of these images, ones used for this report or photocopied for the HAER record are cited by negative number. D. Unpublished Manuals and Manuscripts "Control and Energy Conversion Division, Facility Utilization ETS, Edwards Test Station, Edwards, California." .Unpublished Manuscript. Frank C. Brown & Company, Inc. "Toxic Exhaust Scrubber Facility." Revised December TYpescript operator's manual on file at JPL Edwards Facility, Edwards AFB, California. Gibbons, John, and William C. Tibbitts. Edwards Facility Historic Overview." Typescript on file at AFFTC/EM, Edwards AFB, California,
Jpl Edwards Facility
Edwards Test Station) HAER No. CA-163 (Page E. Reports Austin-Field & Fry A.I.A. Planning, Architecture, Engineering. Master Planning Program, Edwards Test Station, Report No. 1 August National Aeronautics and Space Administration, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California. Report on file at JPL Edwards Facility, Edwards AFB, California. Daniel, Mann, Johnson, and Mendenhall. Master Facilities Plan Report on file at JPL Edwards Facility, Edwards AFB, California. Hudlow, Scott M. Cultural Resource Evaluation of the North Base Complex (The Muroc Flight Test Base and the Rocket Sled Test Track), Edwards AFB, Kern County, California. Report on file at AFFTC/EM, Edwards AFB, California, Johannesmeyer, James, and Margaret Ronning.
Phase I Historic Properties Inventory for the Proposed Closure of the Jet Propulsion Laboratory, Edwards AFB, Kern County, California. Report on file at AFFTC/EM, Edwards AFB, California, Koebig & Koebig, Inc., Engineering, Architecture, Planning, December Master Plan for Edwards Test Station, National Aeronautics and Space Administration, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California. Report on file at JPL Edwards Facility, Edwards AFB, California. Shoop, Richard L. Historical Report of Technical Engineering, Army Air Field Base Unit, Muroc, California, for the Month of May Report on file at AFFTC/HO, Edwards AFB, California. F. Interviews and Telephone Communications: Bluth, John. (Archivist, Jet propulsion Laboratory, Pasadena, California).
Telephone conversations with Scott M. Hudlow. Bonner, John ("Dick") Richard. (Test engineer, JPL Edwards Facility). Personal interviews and telephone conversations with Richard K. Anderson, Jr and Scott M. Hudlow. Malina, Frank J. Interview by James H. Wilson, 8 June JPL Archives, Oral History Program. Transcript of interview on file at the JPL Archives, Pasadena, California. JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Moran, Cliff. (Chemist, Member of Technical Staff, JPL Pasadena, California). Telephone conversations with Richard K. Anderson, 20 March and 27 June, Stapp, John Paul. Interview by Richard Wessel, Linda Stowe, Lewis Hiede, Ted Liveratos, and Frank Kou on 10 December at Edwards APB, California. Transcript on file at AFFTC/EM, Edwards AFB, California. II.
SECONDARY A. Books Advisory Council on Historic Preservation. Balancing Historic Preservation Needs with the Operation of Highly Technical or Scientific Facilities. Washington, DC: Advisory Council on Historic Preservation, Baker, David. The Rocket: The History and Development of Rocket & Missile Technology. New York, New York: Crown Publishers, Inc., Bishir, Catherine, Carl Lounsbury, Charlotte Brown, and Ernest Wood III. Architects and Builders in North Carolina: A History of the Practice of Building. Chapel Hill, North Carolina: University of North Carolina Press, Butowsky, Harry A. Man-in-Space National Historic Landmark Study. Washington, National Park Service, Department of Interior, Caidin, Martin.
Countdown for Tomorrow: The Inside Story of Earth Satellites, Rockets and Missiles and the Race Between American and Soviet Science. New York, New York: E. P. Dutton and Co., Inc., Cent~r For Air Force History. Coming in from the Cold: Military Heritage in the Cold War. Report on the Department of Defense Legacy Cold War Project, Dibblee, Thomas W. "Geology of the Rogers Lake and Kramer Quadrangles, California." USGS Bulletin U.S. Department of the Interior, Geological Survey (USDI-USGS), Washington, U.S. Government Printing Office, JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Garner, John S. World War II Temporary Military Buildings: A Brief History of the Architecture and Planning of Cantonments and Training Stations in the United States.
USACERL Technical Report, Champaign, Illinois, Hampel, Clifford A. Rare Metals Handbook, 2nd ed. London: Reinhold Publishing Corporation, Koppes, Clayton R. JPL and the American Space Program: A History of the Jet Propulsion Laboratory. New Haven, Connecticut: Yale University Press, Kreger, Robert David. "The Making of an Institutional Landscape: Case Studies of Air Force Bases, World War I to the Present." diss., University of Illinois, Champaign, Illinois, Ley, Willy. "V.2-Rocket Cargo Ship," reprinted in Famous Science- Fiction Stories: Adventures in Time and Space. Raymond J. Healy and J. Francis McComas, eds. New York, New York: The Modern Library, McDougall, Walter . . . . The Heavens and the Earth: A Political History of the Space Age.
New York, New York: Basic Books, Morrison, David and Jane Sarnz. voyage to Jupiter. NASA Washington, National Aeronautics and Space Administration, Murray, Bruce. Journey into Space: The First Thirty Years of Space Exploration. New York, New York, Norton, Neal, Valerie, Cathleen S. Lewis, and Frank H. Winter. Spaceflight: A Smithsonian Guide. New York, New York, Macmillan, Neufeld, Jacob. The Development of Ballistic Missiles in the United States Air Force, Washington, Office of Air Force History, Newell, Homer E. Beyond the Atmosphere: Early Years of Space Science. Washington, National Aeronautics and Space Administration, JPL EDWARDS FACILITY Edwards Test station) HAER No. CA-163 (Page Noble, David. America by Design: Science, Technology, and the Rise of Corporate Capitalism.
New York, New York: Oxford University Press, pursell, Caroll W. "The History of Technology and the Study of Material Culture" in Material Culture: A Research Guide. Thomas J. Schlereth, ed. Lawrence, Kansas: University Press of Kansas, Upton, Dell. "The Preconditions for a Performance Theory of Architecture," Comment on "Time and Performance: Folk Houses in Delaware," by Bernard Herman in American Material Culture and Folklife: A Prologue and Dialogue, Simon Bronner, ed. Ann Arbor, Michigan: UMI Press, Vasek, Frank C. and Michael G. Barbour. "Mojave Desert Scrub Vegetation," in Terrestrial Vegetation of California. Michael G. Barbour and Jack Major, eds. New York, New York: John Wiley and Son, Vlach, John.
"The Concept of Community and Folklife Study" in American Material Culture and Folklife: A Prologue and Dialogue. Simon J. Bronner, ed. Ann Arbor, Michigan: UMI Research Press, B. Periodicals Activities at White Sands and Edwards Commence in LAB-ORATORY, May, "Edwards Tests Station Marks Birthday." LAB-ORATORY. April, "What's Happening at Edwards." LAB-ORATORY. April, C. Brochures National Aeronautics and Space Administration and Jet propulsion Laboratory. The Edwards Facility. JPL pasadena, California: Jet Propulsion Laboratory, November ~RNo. CA-163
Addendum to
Jet Propulsion Laboratory Edwards Facility Edwards Test Station} Edwards Air Force Base /5 -BOfi\oN. VI Boron Vi ci nity /- Kern County California
Photographs Written Historical and Descriptive Data
Historic American Engineering Record National Park Service Department of the Interior San Francisco, California cAL /5-Bo~oN. V /_ J HISTORIC AMERICAN ENGINEERING RECORD INDEX TO PHOTOGRAPHS ADDENDUM TO Jet Propulsion Laboratory Edwards Facility, HAER No. CA-163 Edwards Test Station) (Page 4) Edwards AFB Boron Vicinity Kern County California Photographs CA-163-1 to Ca-163-7 were transmitted to Library of Congress in Photographers' Credits: Credi t Photographic copy of JPL photograph by William C. Tibbitts, date cited in caption Credit Philipp S. Ritterma=, Photography & Preservation Associates, Inc., September, All Jet Propulsion Laboratory materials are in the public domain, having been completed under U.S ..Government funding.
CA-163-8 Credi t Original 4" x 5" black and whi te negative housed in the JPL Archives, Pasadena, California. This aerial photograph displays solid propellant line structures E-34 through E-40 negative no. 384-6572A, 24 May CA-163-9 Credit This overview displays the concentration of JPL solid propellant production buildings as seen when looking directly north from the roof of the Administration Building (4231/E-32). The structures closest to the camera contain the equipment for weighing, grinding, mixing, and casting solid propellant grain for motors. Structures in the distance generally house curing or inspection activities . . - JPL.EDWARDS FACILITY HAER No.
CA-163 INDEX TO PHOTOGRAPHS (Page 5) CA-163-10 Credit This group view shows propellant preparation buildings 4241/E-42, 4242/E-43, and 4243/E-44 (left to right) as seen when looking northwest ). Note the warning lights at the extreme left of the view, and the use of lightning rods on structures. Building 4241/E-42 housed solid rocket motors after they were cast and awaiting curing. Building 4241/E~42 was the Preparation Control center which housed remote controls for operations in the other two buildings. Buildings 4243/E-44 housE!d a remotely controlled mandrel puller for pulling mandrels (casting cores) from cured grain, and a vertical lathe for trimming grain to shape and size . HA t< CAL. IS-eaR-oN. V J 1- .
Addendum to JET PROPULSION LABORATORY EDWARDS FACILITY HISTORIC AMERICAN ENGINEERING RECORD HAER No. CA-163 (Page
Jet Propulsion Laboratory Edwards Facility
Edwards Test Station) This report is an addendum to a 119 page report previously transmitted to the Library of Congress in l "Real Record - 1dings," a cards on each structure at JPL Edwards Faci1i construction, alterations and costs. Records on file at AFFTC/CE-RE (Real Estate), Edwards AFB, California. B. Maps and Drawings California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings 0 structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California. C. tori cal Photographs A large collection estimated at images was reviewed at JPL Edwards Ii Original negatives are retained JPL at its Pasadena, California headquarters as and of these , ones used for s report or photographically the HAER record ted by negat number.
D. l"lCHIIJa..L S Manuscripts A., S. H. Kalfayan, and C. A. Propellant Development." on Vol. 5; Laurel, MD: Johns Hopkins Laboratory, Chemical s on JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Department of the Air Force. AFR Explosive ty Standards. Document on File, AFFTC/SEW, Edwards AFB, California, Gibbons, John, and William C. Tibbitts. Edwards Facility Historic Overview." Typescript on file at AFFTC/EM, Edwards AFB, California, Jet Propulsion Laboratory. Control and Energy Conversion Division. Facility Utilization ETS. Edwards Test Station. Edwards, California. JPL Edwards Facility Collection. Report on Ie in temporary storage, Dryden Flight Research Center, Edwards AFB, California, part of the JPL Archives Collection, Pasadena, California.
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California. JPL Spec[ification] GMO-50065-TST, 22 October Test Specification Ammonium Perchlorate Analysis Methods (typescript). JPL Edwards Facility Collection. Collection ln temporary storage, Dryden Flight Research Center, Edwards AFB, California. JPL Archives Collection, Pasadena, California. D. Reports Austin-Field & Fry A.I.A. Planning, Architecture, Engineering. Master Planning Program, Edwards Test Station, Report No. 1 August National Aeronautics and Administration, Jet Propulsion Laboratory, Cali Ins tute of Technology, Pasadena I California. Report on file at JPL Edwards Facility, Edwards AFB, California. Butowsky, Harry A. Man-in-Space National His c Landmark Study.
Washington, National Park Service, Department of Interior, ~G'U.LC~,Mann, Johnson, and Mendenhall. JPL Master Facili es Plan Report on fi at JPL Edwards Facility, Edwards AFB, California. Hudlow, Scott M. Cultural Resource Evaluation of the North Base Complex Muroc Flight Test Base and the Rocket Sled Test Edwards AFB, Kern CountYI Cali I on Ie ,Edwards AFB, Cal JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Koebig & Koebig, Inc., Engineering, tecture, Planning. December Master Plan for Edwards Test Station, National Aeronau cs and Space Administration, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California. Report on le at JPL Edwards Facility, Edwards AFB, California. Powers, L. B. NASA Marshall Space Flight Center, Huntsville, AL; R. L.
Bailey and B. H. Morrison, Jet Propulsion Lab., Pasadena, CA. AIAA-81-1461: Shuttle Solid Rocket Motor Nozzle Alternate Ablative Evaluation. New York, New York: American Institute of Aeronautics and Astronautics, E. Interviews and Telephone Communications: Bluth, John (Archivist, Jet Propulsion Laboratory, Pasadena, California). Telephone conversations with Scott M. Hudlow. Bonner, John ("Dick") Richard. (Test engineer, JPL Edwards Facility). Personal interviews and telephone conversations with Richard K. Anderson, Jr and Scott M. Hudlow. Ray, Robert L. (Test engineer, JPL Edwards Facility). Personal interviews with Richard K. Anderson, Jr. and Scott M. Hudlow. II. SECONDARY A. Books Baker, David. The Rocket: The tory Development of Rocket & Missile Technology.
New York, New York: Crown Publishers, Inc., Bennett, H. se and Technical Dictionary. 3rd ed. New York, New York: Chemical Publishing Company, Bes ,Al The Li and Death of a Satellite: A Biography of the Machines at War with Space. Boston, Massacnuset: t ,Brown and Company, James A. Kent. HLCUCL'S Handbook Industrial Chemis 9 ed. New Chapman & 1, R. JPL Program: A the Jet New Haven! JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page McDougall, Walter . .. . The Heavens and the Earth: A Political History of the Age. New York, New York: Basic Books, Murray, Bruce. Journey to Space: The First Thirty Years of oration. New York, New York: Norton, Neal, , Cathleen S. Lewis, and Frank H. Spaceflight: A Smithsonian Guide. Macmillan: New York, New York, Neufeld, Michael J.
The Rocket and the Reich: Peenemunde and the Coming of the Ballistic Missile Era. New York, New York: The Free Press, Newell, Homer E. Beyond the Atmosphere: Early Years of Space Science. Washington, National Aeronautics and Space Administration, Ordway, III, Frederick I. Pictorial Guide to Planet Earth. Thomas Y. Crowell Company: New York, New York, Paul, Gunter. The Satellite Spin-Off: The Achievements of Space Flight. Robert B. Luce: Washington, , Mitchell R. Satellites and Probes: The Development of Unmanned Spaceflight. Doubleday and Company, Inc.: Garden , New , lding-White, T. M. Jane's Pocket Book of Space Exploration. 1 : New York, New York, lliamson, Mark. Dictionary of Space Technology.
Adam New York, New York, cs and Space Administration and Jet The Edwards li JPL Pasadena, Jet sion Laboratory, les "The Schlereth, ed. Lawrence, Kansas: Universi Press Kansas, 9 JPL EDWARDS FACILITY Edwards Test Station) HAER No. CA-163 (Page Dibblee, Thomas W. "Geology of the Rogers and Kramer Quadrangles, California." USGS Bulle U.S. of or, Geological Survey (USDI-USGS) , Washington, D C.: U.S. Government Printing Of , Vasek, Frank C and Michael G. Barbour. "Mojave Desert Scrub Vegetation." In Terrestrial Vegeta on of California. Michael G. Barbour and Jack Major, eds. . New York, New York: John Wiley and Son,
The federal surveyors worked through Boron building by building. These are the other structures
they measured and filed a report on, longest report first.
Written history. Quoted verbatim from HAER CAL,15-BORON.V,1-. United States federal work, no copyright under 17 U.S.C. 105.
Text capture. Machine-read from the scanned typescript filed with the survey, so spelling and spacing follow the original page.
How this page is made. Documentary passages are quoted from the linked federal record; page labels and counts are clearly marked as site presentation or calculations.