BlockBefore

University of California Radiation Laboratory, Bevatron, 1 Cyclotron Road, Berkeley

University of California Radiation Laboratory, Bevatron, 1 Cyclotron Road, Berkeley, Alameda County, CA. Surveyed as HAER CAL,1-BERK,4-, with a 32,726-word written history.

From the record

“The Bevatron was among the world's leading particle accelerators during a forty-year period from to and is associated with significant contributions in the fields of particle and nuclear physics, thus helping to establish American leadership in scientific research.”

Written record, HAER CAL,1-BERK,4- survey. Machine-read text.

Surveyed by the federal HAER program as HAER CAL,1-BERK,4- · the record runs 32726 words · one of 198 surveyed structures published for this county.

Sources: the survey record at the Library of Congress

Location

147 words

Source document Quoted word for word from HAER CAL,1-BERK,4-. Not written, edited or summarised by this site.

Ernest Orlando Lawrence Berkeley National Laboratory Buildings 51 and 51A One Cyclotron Road Alameda County Berkeley, California U.S.G.S. Briones Valley, California, 7.5-minute quadrangle photorevised and Richmond, California, minute quadrangle photorevised Universal Transverse Mercator Coordinates: 565.9839E, Date of Construction: Altered, Engineers/Architects: Building; Masten and Hurd (architect), Milton T. Pflueger (architect), Huber and Knapik (structural engineers), San Francisco, California Bevatron atomic particle accelerator: William Brobeck (engineer) Builders: Pacific Coast Builders, San Francisco, California Ernest Orlando Lawrence Berkeley National Laboratory Buildings 51 and 51 A 1 Cyclotron Road Alameda County Berkeley, California U.S.G.S.

Briones Valley, California, 7.5-minute quadrangle photorevised and Richmond, California, 7.5-minute quadrangle photorevised Universal Transverse Mercator Coordinates: 565.9839E, Date of Construction: Altered, Engineers/Architects: Building: Masten and Hurd (architect), Milton T. Pflueger (architect), Huber and Knapik (structural engineers), San Francisco, California Bevatron atomic particle accelerator: William Brobeck (engineer) Builders: Pacific Coast Builders, San Francisco, California Huber & Knapik, Engineers

Significance

32461 words

The headings the report itself prints. Each one jumps to where it begins.

Source document Quoted word for word from HAER CAL,1-BERK,4-. Not written, edited or summarised by this site.

The Bevatron was among the world's leading particle accelerators during a forty-year period from to and is associated with significant contributions in the fields of particle and nuclear physics, thus helping to establish American leadership in scientific research. In the late and early four Nobel Prizes were awarded for particle physics research conducted in whole or in part at the Bevatron. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 2 Report Prepared By: Present and former Berkeley Lab scientists and technical staff: Edward J. Lofgren, William Brobeck, Harvey Syversrud, Richard Gough, Lee Schroeder, Glen Lambertson, Gerson Goldhaber, Bill Wenzel, Stevenson, Albert Ghiorso, Stan Curtis, and Joe Castro Date: September, Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 3 Contents Contents 3 Introduction 5 Description of the Bevatron 6 Purpose, Development, and Operation of the Bevatron 7 The Bevatron: 7 The Bevalac: 8 Historical Context: Berkeley Lab and the Development of Particle Accelerators 10 Bevatron Planning Process 13 Bevatron Design 18 Bevatron Upgrades 21 Particle Detectors Used with the Bevatron 22 The Bevatron Transformed: The Bevalac 24 Bevatron Closure 31 Overview of the Historic Significance of the Bevatron 32 Nobel Prize-Winning Research 32 Scientists Associated with the Bevatron 35 Architecture of the Bevatron Building 38 Construction History of the Bevatron Building Complex 38 Architecture of the Bevatron Building Complex 44 Architecture of the Bevatron/Bevalac Building Complex 47 Bevatron Building (Building 51/51A) 47 Future Plans 49 References and Bibliography 50 Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 4 0 100 200 400 600 ft 0 30 60 120 180 XBD TIF (August Berkeley Lab site map, Bevatron Building 51A). Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 5 Introduction T his report highlights the scientific achievements and significant persons associated with the Bevatron/Bevalac from (when construction of the facility began) through when the facility was closed. The report describes the original design of the accelerator machines and buildings, and notes the major design changes that were made as scientific work progressed. A major change took place in when the Bevatron was connected to a linear accelerator known as the SuperHILAC to create the Bevalac.

The following sections are included in this report: The Bevatron, a subatomic particle accelerator, was the largest, highest-energy accelerator in the world as described in the section entitled Description of the Bevatron. Purpose, Development, and Operation of the Bevatron describes this accelerator as an essential tool of high- energy physics and discusses the development and operation of the Bevatron and the Bevalac. Historical Context: Berkeley Lab and the Development of Particle Accelerators provides an historical background of the Laboratory and the particle accelerators. An account of the initial planning, political processes and funding negotiations, and engaging in a competitive race are presented in the Bevatron Planning Processes.

Bevatron Designs describes in detail the design stages, components, magnet, electric fields, injectors, upgrades, and other accelerator developments such as the Bevalac. Bevatron Closure relates the why and when the complex closed. The scientific research and the scientist themselves are recounted in Overview of the Historic Significance of the Bevatron. The Architecture of the Bevatron Building section describes the context of the construction history. Finally, the References and Bibliography section contains a list of sources consulted in the preparation of this report. Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 6 Description of the Bevatron The Bevatron, a subatomic particle accelerator with an energy potential of 6.2-billion electron volts (BeV), was the largest, highest-energy accelerator in the world when it opened in at the University of California Radiation Laboratory (UCRL), predecessor of the Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab).

The Bevatron had been designed for the study of high-energy nuclear processes of the cosmic-energy (a stream of atomic nuclei of heterogeneous extremely penetrating character that enter the earth's atmosphere from outer space at speeds approaching that of light) range, and was the world's "most productive accelerator of the (Seidel, During the and four Nobel Prizes were awarded for particle physics research conducted in whole or in part at the Bevatron. Like most other UCRL facilities, the Bevatron was owned and funded by the U.S. Atomic Energy Commission (AEC; predecessor of the U.S. Department of Energy) and managed by the University of California.

The Bevatron was constructed on land that is under the jurisdiction of the Regents of the University of California and was leased to the AEC (Fig. 1). Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 7 Purpose, Development, and Operation of the Bevatron The Bevatron: The Bevatron was designed by UCRL engineer William Brobeck and staff as a proton synchrotron-a machine that accelerates protons (an elementary particle that is the positively charged constituent of ordinary matter and, together with the neutron, is a building block of all atomic nuclei) until their velocity becomes relativistic as the particles (any very small part of matter such as an electron) approach the speed of light.

The Bevatron was a circular accelerator in which particles were kept in a path of constant radius by a magnetic guide-field that increased concomitant with increasing particle mass. A radio-frequency accelerating apparatus imparted energy to particles that were injected into the Bevatron from an external ion source (Cole and Tigner, Protons in the Bevatron were accelerated by electromagnetic (pertaining to phenomena in which electricity and magnetism are related) forces and all particles moved in the same direction forming a single circulating beam. After the particles were accelerated to the desired energy, the beam was steered toward a target.

When a beam of high-energy protons from the Bevatron struck a target, interactions occurred between the speeding protons and the stationary nuclei (the positively charged mass within an atom) of the target. The interactions often produced particles in the target chamber that did not exist before the collision (Fig. 2). Particle accelerators are designed to cause these interactions and permit study of their results (Cole and Tigner, The accelerator is an essential tool of high-energy physics, used to accelerate particles to very high energy so that the particles can probe the innermost structure of matter and the forces that govern its behavior.

In the interaction between a projectile particle and the target particle it strikes, new kinds of particles can be produced that provide clues to the nature of matter. These particles are usually short lived and decay radioactively in a time much less than a microsecond. Such reactions were produced copiously in the first moments of the "big bang" (a theory of the origin and evolution of the universe) from which our universe is believed to have evolved, but are now produced only infrequently in nature by cosmic rays. Systematic study of these particles and their interactions requires controlled, copious production using accelerators. (Cole and Tigner, The greater the energy of the protons striking the target, the more massive or numerous the newly-created particles were likely to be.

The creation of new particles (such as mesons* or baryonst) is a consequence of the strong force-stronger than the *Any elementary (noncomposite) particle with strong nuclear interactions and baryon number equal to zero. t Any elementary particle which can be transformed into a nucleon and some number of mesons and lighter particles. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 8 electromagnetic force-which binds protons and neutrons+ together in atomic nuclei. Studies of the production and properties of new particles led to the discovery of the strong force. One characteristic of new particles is that they are not stable; they interact or spontaneously break up after very short lifetimes, typically measured in billionths of a second.

Their disintegrations, called decay interactions, are a manifestation of the weak force-weaker than the electromagnetic force. Deeper penetration of a particle requires progressively higher energies in the bombarding particles. The Bevatron was in the vanguard of physics research in the late because of its capacity to generate the highest energies produced by accelerators of that period. The highest velocity that protons attained in the Bevatron was miles per second, or of the speed of light (Fig. 3). This is equivalent to an increase in energy of 6.2 BeV (Barklow and Perl, The Bevatron was the most powerful accelerator in the world from to and dominated the field of high-energy physics until the early By the late during a period of substantial U.S.

government support for physics research, and rapid advances in accelerator design, the Bevatron had been superseded by more powerful accelerators at other laboratories. William Wenzel, who began work at UCRL as a postdoctoral student from California Institute of Technology in has identified the period through as one of "decline and transfiguration" at the Bevatron. An AEC congressional report projected the shutdown of the Bevatron in (Wenzel, The Bevalac: The scientific utility of the Bevatron was extended in by a proposal promulgated by Albert Ghiorso, a laboratory nuclear chemist, to connect the Bevatron to the nearby SuperHILAC (Heavy Ion Linear Accelerator). This resulted in a hybrid facility known as the Bevalac.

From through the Bevatron was modified under the direction of Edward Lofgren, Division Head of the Accelerator Division, and Hermann Grunder, a specialist in accelerator design and later Bevalac Group Leader. The SuperHILAC linear accelerator was used as a means for injecting heavy ions into the Bevatron, thereby expanding the research potential from a singular particle source (protons), to ions of every naturally-occurring element.

With the operation of the Bevalac beginning in the focus of research at the Bevatron shifted from the acceleration of protons to the acceleration of heavy ions (ions heavier than helium) and from high-energy particle physics research to three new areas of research: nuclear heavy-ion physics; medical research and therapy in cancer treatment; and cosmic ray experiments which simulated conditions encountered by astronauts in outer space.

After the Bevalac was upgraded in it was the only accelerator in the world capable of accelerating ions of all the naturally-occurring elements of the periodic table (a table of the elements, written in sequence in the order +An elementary particle which has approximately the same mass as the proton but lacks electric charges, and is a constituent of all nuclei having mass number greater than of a proton. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 9 of atomic number or atomic weight), from the lightest-hydrogen-to the heaviest- uranium.

The Bevalac retained this distinction and maintained an active research program until the facility was closed by the Department of Energy (DOE) in February, Throughout the whole period of its operation, from through the Bevatron/Bevalac was used not only by scientists at UC Berkeley but by visiting scientists from around the country, as well as foreign scientists from Europe, the Soviet Union, Israel, Japan, and other countries. Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 10 Historical Context: Berkeley Lab and the Development of Particle Accelerators UCRL: The University of California Radiation Laboratory was organized in on the main campus of UC Berkeley by physics professor Ernest Orlando Lawrence, who invented the cyclotron, a circular particle accelerator, in (Heilbron et al., :11 ). The Laboratory was renamed the Lawrence Radiation Laboratory in in memory of its founder; in the name of the Laboratory was changed to the Lawrence Berkeley Laboratory, and in it was renamed the Ernest Orlando Lawrence Berkeley National Laboratory. The cyclotron provided a "long-sought breakthrough into the realm of high- energy physics" by applying Lawrence's principle of repetitive acceleration.

In the direct-voltage accelerators had been developed which gave particles a single, accelerative push. The direct-voltage accelerator was, however, severely limited in its energy range. In a cyclotron, accelerating particles travel a spiral path within a relatively small space, receiving repetitive applications of comparatively small voltages. This exposure to many accelerative pushes results in the acceleration of particles to high energies. The first practical cyclotron, built in by Lawrence and M. S. Livingston, was an 11-inch instrument (with magnet pole faces 11 inches in diameter) and yielded charged particles of sufficient energy to cause nuclear disintegrations.

Rapidly succeeding generations of larger and more efficient cyclotrons (27.5-inch, 37-inch, 60-inch) continued to establish frontiers of new energy ranges and deeper penetrations of the atomic nucleus. University officials rewarded Lawrence for his success with the cyclotron program in by establishing the Radiation Laboratory as an independent division of the UC Berkeley Physics Department. The vast potential of cyclotron research at UC Berkeley, and elsewhere, had by that time gained international recognition. With Lawrence's help, cyclotrons were built at other universities in the United States, as well as in Europe, the Soviet Union, and Japan.

In at the age of 38, Lawrence received the Nobel Prize in physics for his invention of the cyclotron and for his pioneering research (Lawrence, The award was a triumph not only for Lawrence but for the University of California because Lawrence was the first professor at a public university in the United States to receive the Nobel Prize (Childs, The physicist and cold war historian Herbert York, one of the early students at the Radiation Laboratory, summarizes in the following passage the substance of the cyclotron invention and Lawrence's enduring contribution to the field of accelerator design: [The cyclotron] was a machine for accelerating protons and other nuclear particles to high velocities by means of an ingenious combination of oscillating electric and static magnetic fields.

Its basic purpose was to probe the properties of the atomic nucleus and to investigate its constituents. There were other machines for this purpose-all were Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 11 popularly called atom smashers-but Lawrence's cyclotron proved to be the most powerful and effective. More important, his approach appeared to offer the potential for virtually unlimited further development and extension. In fact, more than half a century later, nearly all of the world's huge particle accelerators are based on concepts that, while different in detail and generally much more elaborate, are the direct descendants of Lawrence's original invention.

(York, UCRL: Lawrence's Nobel Prize helped generate funding from UC and the Rockefeller Foundation for the expansion of programs and facilities at the Radiation Laboratory during the early Having outgrown its original site on the main campus of UC Berkeley, the Laboratory focused its plans for future development on Charter Hill, University property located east of the main campus, which had a commanding view of the University, the City of Berkeley, and San Francisco Bay to the Golden Gate. This hill, rising above the Greek Theater and the football stadium (existing UC facilities on the main campus), has been seen as a "romantic site" (Heilbron et al., or a "picturesque site" (Gebhard, intended as a showcase for the largest cyclotron ever built-the 184-inch cyclotron.

Construction of this "'he-man cyclotron,' the 'father of all cyclotrons"' (Heilbron and Seidel, began in and has served since that time as a "visually dominant structure [that would] assert the pre-eminence of science" (Gebhard, Historians Heilbron and Robert W. Seidel, who have written the definitive history of the early years of the Rad Lab, described the entrepreneurial spirit that drove Lawrence and UC President Robert Gordon Sproul in their quest for newer and bigger accelerators. The success of the cyclotron had inspired competitors, including two clones of the 60-inch; if the Laboratory wished to stay ahead, it must cross the new frontier where, as cosmic ray studies indicated, 'strikingly new and important things' were to be found. Sproul wanted to keep Berkeley ahead.

(Heilbron and Seidel, These ambitions were fed both by timely scientific innovations and by generous patronage-by private foundations during the pre-war period and federal government agencies during and after World War II.

The UC Regents also played a vital role as Laboratory sponsors by approving contracts with the AEC for university management of UCRL and by providing university land for Laboratory expansion (Seidel, During World War II, UCRL accelerators that had originally been built for physics research were mobilized by the Manhattan Engineer District (MED) for the development of a prototype for electromagnetic separation of uranium (a metallic element in the actinide series, highly toxic and radioactive) isotopes (one of two or more atoms having the same atomic number but different mass number) used in nuclear explosives. The weapons program generated rapid development of UCRL facilities and personnel; by there were more than thirty buildings and laboratories on the main campus and Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 12 Charter Hill, and a staff of more than scientists, technicians, and engineers (Seidel, UCRL:

Immediate Postwar Period

The Bevatron was the first UCRL building to be constructed on the Frank Wilson Tract, a 97-acre parcel which adjoined the main university campus on the north, and Charter Hill (the 184-inch cyclotron area) on the south. After the World War II, the Wilson tract had been considered as a possible site for the United Nations headquarters (California Monthly, The partnership of the physics community and the U.S. government that had been established for the weapons program during World War II continued during the postwar period.

The arms race with the Soviet Union during the Cold War provided new justification for sponsorship of physics research and accelerator projects that had potential military applications (Brown et al., At the end of World War II, when physicists returned to their laboratories, the enhanced status of nuclear physics was immediately evident. The exciting and dangerous development of atomic energy, with its tremendous implications for national security, stimulated strong popular support for spending government funds on building still larger and higher-energy accelerators. (Livingston and Blewett, [quoted in Brown et al., Accelerator development in the years just after World War II was, Heilbron argues, the result of a "trade-off, more or less explicit, between physicists and government.

According to this account, university physicists received generous support for research that was little, if any, direct concern to the sponsoring agency, in return for supplying trained manpower and technical advice. Most of the trained with AEC funds at university accelerator laboratories did go to work for the AEC in one way or another" (Heilbron, ). The Rad Lab's contribution to the success of the atomic bomb program during the war ensured government support for the continued expansion of Laboratory programs and facilities in the immediate postwar period.

"Lawrence knew that science would be both honorably discharged and held in ready reserve for the national defense and welfare" (Heilbron et al., "One of the greatest scientific promoters of his time," (Seidel, Lawrence secured funding from the MED and the AEC (successor to MED) for an ambitious development program that focused on four new accelerators: the 4,000-ton 184-inch synchrocyclotron completed in initially operating at 380 million electron volts (MeV ); a synchrotron (operational in designed for the acceleration of electrons to 300-million volts; a linear accelerator (completed in November, incorporating Luis Alvarez's ideas for the use of microwave power (an electromagnetic wave which has a wavelength between about 0.3 and 309 centimeters, corresponding to frequencies of gigahertz) to accelerate protons to high energies; and the Bevatron, designed in for the acceleration of protons to energies of over 6 BeV.

Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 13 Bevatron Planning Process The initial planning for the Bevatron occurred in the late during a period of rapid dissemination of accelerator ideas, fostered both by cooperation among and competition between various research laboratories. William Brobeck, head engineer at UCRL, designed a 10-BeV proton synchrotron in the fall of after taking an engineer's course on accelerator construction at UCRL in the summer of The 10- BeV energy limit was set because it seemed "the largest machine that could be made in the near future without departing from the techniques used on machines at present in operation" (Brobeck quoted in Heilbron et al., The physicist I.I.

Rabi borrowed copies of Brobeck's plans to persuade officials at Brookhaven National Laboratory in New York to undertake a similar accelerator program there. Mark Oliphant, a physicist in Birmingham, England, who had visited UCRL during the War, and was familiar with the concept of phase stability (a principle governing the stability of motion of particles in a synchrotron), had by this time already planned a 1.3-BeV proton synchrotron, scheduled to begin operation in late (Actual operation of the Birmingham machine was delayed until June, With this array of competition, "Lawrence knew, therefore, that he would have an uphill fight to win AEC support for Brobeck's machine, which he needed to remain ahead in accelerator design" (Quote from Seidel, Childs, ).

Political processes and funding negotiations played a crucial role in the design of the Bevatron's energy threshold (Seidel, Seidel, Heilbron, Lawrence first sought approval from the AEC in for million for a 10-BeV proton synchrotron designed by UCRL's head engineer, William Brobeck. When this proposal exceeded AEC budget limitations, Lawrence cut the energy capacity for the Bevatron in half, to 5 BeV. UCRL physicists Edwin McMillan and Wolfgang Panofsky suggested an energy of 6 BeV, the level estimated to be necessary for the production of antiprotons (Seidel, In late and early UCRL and Brookhaven National Laboratory engaged in a competitive race for design and approval of proton synchrotrons in the 2 to 6 BeV range.

Brookhaven National Laboratory countered Lawrence's proposal to the AEC with one of their own for a 2.5-BeV proton synchrotron (a device for accelerating protons in circular orbits in a time-varying magnetic field, in which the orbit radius is kept constant) to produce pions (mesons having a mass from approximately 264 to approximately 273 times that of any electron with positive, negative, or zero charge and spin of zero) in pairs. Lawrence then revised his proposal from a 6.2-BeV machine to a 1.8 BeV (for pion production) which could be expanded to 6.5 BeV by doubling the size of the magnet and quadrupling the generator capacity.

The General Advisory Committee (GAC) of the AEC ultimately took the diplomatic course by recommending in February, that "two machines, aimed at substantially different maximum energies, should be built and that the energies and locations [of each] should be determined as a result of consultation between the laboratories" and the AEC (Seidel, The GAC recommendation left open the vital question of which laboratory would win approval for a higher-energy machine. On March 8, Lawrence revised his Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 14 proposal again, now calling for a larger machine with a radius of 55 feet, with a primary goal of "the achievement of 6-7 BeV protons." Brookhaven National Laboratory adhered to its original proposal for a 2-3 BeV machine (named the Cosmotron) with hopes of eventual construction of a 10-BeV machine. The GAC approved the two proposals-a 3-BeV Cosmotron and a 6-BeV Bevatron-on April 14, as "major tools for basic research" (Seidel, Childs, AEC

Decision to Build the Bevatron

The Bevatron was planned as the largest accelerator in the world in the mid-1950s. Heilbron has posed the question, was the machine built?" The normal response of the physics community-that the Bevatron was built for pure physics research, specifically for the discovery of the anti proton (negative proton)-is only part of the answer. Heilbron analyzes the AEC's reasons for funding the Bevatron and other postwar accelerator projects (Heilbron, ): 1. The AEC built the Bevatron in order to investigate nuclear forces in the hope that they might be exploited in new weapon technology. 2. The AEC did not build the Bevatron so much to knock the nucleus to pieces as to provide an opportunity to keep the experienced engineering staff at Berkeley together for mobilization in a national emergency. 3.

The AEC cared little about particle physics, but much about maintaining good cheer at Berkeley, which was the only one of the Manhattan Engineering District's installations untouched by the severe decline in morale and staff suffered by the district immediately after the war. 4. The Bevatron, despite its uniqueness in energy, is best understood as only the biggest of the many redundant accelerators commissioned at universities in the immediate postwar years by the Manhattan Engineer District, the Office of Naval Research, and the AEC. The AEC's authorization of the Bevatron, the fourth major accelerator at UCRL in the immediate postwar period, underscored the pre-eminence of the Radiation Laboratory's leadership in high-energy physics.

Lawrence's success was due not only to technical and scientific ability but to his effective organization of the Laboratory and political finesse in negotiations with the AEC. "Lawrence could not have succeeded in his courtship of the federal patron had his Laboratory not demonstrated its remarkable facility for reconversion to peacetime research that was attractive to the scientific community as well as important to a fundamental understanding of nuclear forces. Another special feature at Berkeley was that accelerator design and construction, unlike reactor development, did not involve security problems or the use of 'special materials' controlled by the AEC.

While Argonne, Oak Ridge, and Brookhaven jockeyed for priorities in reactor development, the Radiation Laboratory steamed ahead on its accelerator projects and abandoned its plans for a reactor. The Laboratory's early postwar successes, peaking in the production of the pion, testified to the high morale and determination of its scientists and engineers, to the effectiveness of the postwar organization, and to the leadership of Lawrence and his senior staff. By accelerating science along the path of crash programs for large-scale technological development in Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 15 science, the Radiation Laboratory helped set the tone of modern big science" (Seidel,

Proton Synchrotron Development

The British scientist John B. Adams views the Bevatron and other synchrotrons of the postwar period as the beneficiaries of an exceptionally smooth evolution of accelerator design and development that had begun with Lawrence's cyclotrons of the early What happened was that one type of machine succeeded another and as each type reached a limiting energy, sometimes for fundamental reasons but more often because extending its energy would have led to prohibitive costs, a new idea was put forward which overcame these limitations and allowed higher energy machines to be built. The remarkable thing was that these new ideas arrived at just the opportune moment so that the research proceeded rather smoothly from one energy range to the next.

When the cyclotrons of Lawrence and Livingston were reaching their energy limit due to relativistic effects causing the particles to drop out of phase with their accelerating voltage, McMillan and Veksler invented phase stability. The cyclotron became the synchrocyclotron and the energy limit was extended from about 20 MeV to nearly 1 GeV. [GeV is equivalent to BeV]. When the huge magnets of the synchrocyclotrons looked like becoming an economic limitation, annular magnets were adopted and the accelerating voltage frequency was tracked with the rising magnetic field to keep the particles circulating at constant radius as their energy increased. This new type of machine, called the synchrotron, enabled the energy limit to be pushed up by another order of magnitude to 10 GeV.

(Adams, The advance in accelerator design represented by the Bevatron and other proton synchrotrons can be shown through a brief comparison with earlier, pre-war accelerators. Accelerators used in nuclear research before World War II were all limited in maximum energy, and could not maintain acceleration indefinitely. In the early cyclotrons, for example, the relativistic increase in mass of protons (an elementary particle that is the positively charged constituent of ordinary matter and, together with the neutron, is a building block of all atomic nuclei) and deuterons (a positively charged particle consisting of a proton and a neutron, equivalent to the nucleus of an atom of deuterium) destroys the validity of the resonance principle for energies above about 25 MeV.

In the cyclotron, the magnetic field that guided the particles in their circular orbits was constant in time. The iron magnets that produced the fields got bigger and bigger- up to hundreds of tons-as the energy of the machine increased. In a synchrotron such as the Bevatron, by contrast, the magnetic fields are designed to increase in time as the particle energy is increased by a radio-frequency accelerating voltage. A synchrotron is an accelerator for charged particles using the principle of magnetic resonance of the cyclotron and exploiting the characteristics that Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 16 these orbits are stable in phase for small deviations from the proper resonance energy to permit a variation of the magnetic field or both the magnetic field and the accelerating frequency during the acceleration. (Lofgren, The synchrotron principle of magnetic particle acceleration derived from three independent sources all occurring within a few years of each other. The first proposal for a proton accelerator was made by Marcus Oliphant of the University of Birmingham, England, in although the proposal was not published until 194 7.

The Bevatron also drew upon the idea of phase stability developed by two scientists working independently-a Russian scientist Vladimir Veksler and Edwin McMillan of UCRL Both versions of the phase stability concept "presented methods by which particles in resonance-type accelerators could be kept in resonance with the radio frequency fields indefinitely, and could be accelerated to much higher energies" (quote from Veksler, McMillan, Livingston, Phase stability is the: ... observation that particles in such a machine [synchrotron] tend to travel in bunches. Suppose the protons, say, get out of step with each other as they move around the ring. Some will then arrive sooner and some later at the places where they are to be accelerated.

Since the accelerating fields are changing with time, things can be accelerated so that a particle that arrives too soon will get a smaller boost than one that arrives on time. The effect on a particle that arrives too late will be just the opposite. The net result is that the particles get locked together in bunches. (Bernstein, The Bevatron, and other proton synchrotrons, were the "culmination of phase-stable accelerators," and produced the highest energies of the accelerators built in the immediate postwar period (Livingston, Other postwar accelerators were relatively restricted in energy range. Electron synchrotrons had a practical energy limit of the order of 1 BeV due to the rapid onset of radiation losses.

Linear accelerators were not yet well enough developed to venture into the BeV range. The synchrocyclotron required a solid core magnet which at this level of energy was exorbitant in weight and cost. In the proton synchrotron a ring magnet is used to reduce cost, and protons can be used to avoid radiation loss limitation. The proton synchrotron uses a ring magnet to produce a magnetic field over an annular region, in which a doughnut-shaped vacuum chamber is located. Protons produced at low energy in an external source can be focused and deflected into the vacuum chamber. The magnetic field guides the particles in a circular orbit of constant radius, and is modulated from low to high intensity as the protons gain energy.

An electric field to accelerate the protons is provided at one point in the circular path, so that the particles acquire an increment of energy on each revolution; this accelerating field must be oscillatory in nature and synchronized with the Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 17 motions of the ions (an isolated electron or positron or an atom or molecule which by loss or gain of one or more electrons has acquired a net electric charge). Since proton velocity increases with energy, the frequency of the applied electric field must be varied during the acceleration to match the increasing angular velocity of the particles.

This frequency must be precisely controlled to provide the correct phase of the accelerating field, so as to maintain constant orbit radius and prevent loss of particles by striking the walls. (Livingston,

Comparison of Bevatron and Brookhaven's Cosmotron

Both the Bevatron and the Cosmotron were proton synchrotrons of the race track design with four straight sections between magnet quadrants. The Bevatron also had a straight section for a drift-tube accelerating electrode. Low-energy accelerators were used as injection sources of protons. For the Bevatron, a proton linear accelerator (linac) was used. The Bevatron had a double-magnetic return circuit similar in cross section to the standard cyclotron magnet (Livingston, John Blewett has compared the Bevatron with the Cosmotron. The basic design features of the Bevatron are similar to those found in the Brookhaven Cosmotron. The proton orbit consists of four circular quadrants about 50 feet in radius separated by field-free straight sections 20 ft. long.

The component designs in the Bevatron, however, differ from those in the Cosmotron in most cases. The Bevatron magnet, for example, is roughly symmetrical about the proton orbit, with two magnetic return yokes, one inside and one outside the orbit. The design is less susceptible to yoke saturation effects than is the C-shaped magnet of the Cosmotron, but it does not permit the easy access to the vacuum chamber that is possible with the C-shaped magnet. The radio-frequency accelerating unit is a short drift tube whose capacity is continuously tuned by saturation of a ferrite-cored inductor, whereas the accelerating unit in the Cosmotron is a ferrite-loaded cavity.

Injection into the Bevatron is at 10 MeV from a linear accelerator instead of the 4 MeV electrostatic injection used in the Cosmotron. (Blewett, Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 18 Bevatron Design UCRL built a quarter-scale model of the Bevatron in to work out design problems. Success with the model prompted the start of construction of the full-scale version in September, (Childs, The quarter-scale model was sent to the California Institute of Technology, and after upgrading was used for several years to accelerate electrons (Fig. 4).

Progress on the Bevatron was interrupted between and by the diversion of Rad Lab scientists to a new project, a materials-testing accelerator (MTA) built at an abandoned naval air station at Livermore, California, 45 miles east of Berkeley. The MTA, a proton linear accelerator designed for the production of critical materials, was considered a top priority after the explosion of the first Soviet atomic bomb in led to a new period of Laboratory mobilization for national defense. Difficulties in the design and operation of the MTA, and the discovery of new sources of uranium in the western United States, led to termination of the MTA project, and the return of Rad Lab personnel to Berkeley and to the Bevatron in (Seidel, ).

The Bevatron was in operation by early and reached the target of more than 6 BeV in April, (Childs, One of the central questions in Bevatron design was the size of the beam aperture. Brobeck's original design called for a large aperture between the magnet poles, 4 feet high by 14 feet wide, but this would have produced protons of only 1.5 BeV. Work on the quarter-scale model in and with the Brookhaven Cosmotron (inaugurated in provided experience that made possible a fine tuning of design for the full-scale machine, and brought about a redesign of the aperture. In UCRL planned the Bevatron with an aperture of 2 feet by 6 feet for an energy of BeV, with allowances for future modification for an energy range of up to 6 BeV.

In December, it was decided to plan directly for a 6-BeV machine, with an aperture of 1 foot by 4 feet. The diversion of UCRL personnel to the MTA project had delayed the completion of the Bevatron by two years, whereas the Cosmotron began operation in Yet, the Bevatron profited from the delay because of experience gained from the quarter-scale model and the Cosmotron. "When completed in the 10,000-ton synchrotron could accelerate well-behaved protons through turns in seconds without their deviating from the median orbit by more than a few inches. Their journey to 6.2 BeV lasted miles" (Heilbron et al.,

Bevatron Components

The Bevatron had a magnet diameter of approximately 120 feet, and dominated the interior of the Bevatron Building (Figs. The massive ring-shaped electromagnet was divided into quadrants (Figs. 8, 9), producing a magnetic guide-field that kept the protons on a path of more or less constant radius during acceleration. Once during each revolution the circulating protons passed through an accelerating electrode where they experienced a small forward push and gained a little energy. To accumulate high energies they had to pass through the electrode millions of times. Acceleration was accomplished by two electric fields, one at the entrance to the accelerating electrode Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 19 and the other at its exit.

These fields were produced by a radio-frequency oscillator connected to the electrode. At every instant during acceleration the energy of the protons, the strength of the magnetic guide-field, and the frequency of the rf had to be perfectly matched to keep the protons in orbit at the proper radius. Because of this requirement, the Bevatron could not deliver a continuous stream of high-energy particles, but instead delivered them in bunches or pulses. The acceleration of a typical bunch took about two seconds. When the desired energy was reached, the protons were extracted for experimentation. Then the magnetic field and oscillator frequency returned to their initial values to prepare for the next cycle.

The time from the beginning of one cycle to the beginning of the next was about six seconds.

The Bevatron Magnet

Almost the entire mass of the Bevatron, except for the shielding, was devoted to producing the magnetic guide-field. The heaviest part was the huge magnet, which contains approximately tons of iron. In addition, approximately 347 tons of copper were used in the 26 miles of heavy cable in which the magnet was wound (Figs. The whole assembly weighed about as much as a medium sized naval cruiser, and its power requirements are prodigious. The two motor- generator and flywheel sets that supply current for the magnet coil must deliver a peak power of kW (kilowatts). The average requirement which must be supplied to the motors by the local power company is close to kW.

The magnetic field is made to rise by applying an essentially direct-current voltage of volts to the magnet coil at the beginning of the acceleration cycle ... In addition to holding the particles in orbit radially, the magnetic field must also apply vertical control. The magnet is designed to produce a magnetic field that bulges slightly toward the outside of the ring. The effect of the bulge is to constrain the protons to a region midway between the top and bottom of the aperture. Thus the particles are focused into a tightly bunched beam, whose radial position is determined by the balance between energy and field strength and whose vertical position is determined by the shape of the magnetic field.

Although in principle the Bevatron could have a truly circular shape, in practice there must be access regions along the path where the protons circulate in the machine for inserting such items as the accelerating electrode, targets, vacuum pumps, etc. The magnet does not cover these regions and therefore the particles travel through them in straight lines. There are four straight sections in the Bevatron; these are called tangent tanks and are designated by points of the compass. The protons are injected into the east tangent tank and are accelerated by the electric fields in the north. The west tangent tank contains target handling facilities. 1969a:4-5)

Electric Fields

The accelerating electrode in the north tangent tank is a rectangular tube constructed for the passage of the protons. Protons gain energy when they pass through the electrode, if they enter it when the voltage is positive and rising. To increase Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 20 their energy to 6.2 BeV, the protons had to circulate times and travel a total of about miles (Fig. INJECTORS The Bevatron had to have an injection system (Fig. 15) for putting the protons into orbit at the start of each pulse. The main function of the injection system was to pre- accelerate the protons to an energy of 19 MeV (Figs. 16, The system consisted of four main parts: 1) An ion source where the protons originated.

The protons accelerated by the Bevatron started as constituents of hydrogen gas. Electrons were removed from the hydrogen atoms, leaving behind the nucleus, or proton. The protons were then attracted by a system of electrodes and directed into a Cockroft-Walton accelerator. 2) Cockroft-Walton type accelerator often called an ion gun (Fig. This was a kind of high-voltage power supply. Protons entering the tube of the Cockroft- Walton were accelerated to an energy equivalent to the voltage of the power supply, delivering protons at about 480 kV. 3) The largest part of the pre-acceleration of protons was accomplished by a linear accelerator, or linac, composed of a cylinder about 3 feet in diameter and 42 feet long. Inside along the axis were 75 metal structures called drift tubes.

Protons traveled through the tubes in a straight line; after 74 successive accelerations, the protons acquired the 19-MeV energy desired for injection (Figs. 19, 4) An inflector, which directed the beam of protons into the main part of the Bevatron. This was essentially a guidance system that steered the protons into the east tangent tank and then directed them into orbit in the Bevatron. Under very good conditions, about 60% of the beam that entered proceeded into orbit. TARGETS AND PROTON

Acceleration in the Bevatron

Once the protons were in orbit in the Bevatron, the accelerating voltage was turned on. The cycle started when a signal from a master timing device instructed the motor/generators to start forcing current through the magnet coils. When the protons had been fully accelerated in the vacuum chamber of the Bevatron, they were directed to some form of target. With an internal target located in the center of the Bevatron aperture, the basic technique was to make the proton energy too low for the existing magnetic field so that the particles spiraled inward. Originally, all the targets were internal to the main ring and the only particles that left the machine were called secondaries, produced when the primary protons collided with one of the targets.

Yet, the massive magnet structure and the magnetic field proved to be obstructions to the placing of targets. In a later development, primary protons themselves were extracted from the accelerator with steering magnets and directed to external targets. They were guided away from the machine after acceleration just as they had been guided into it by the injector at the start. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 21 Bevatron Upgrades When the Bevatron opened in it was the most powerful accelerator in the world. By the early its maximum energy of 6.2 BeV had been surpassed by several new machines at other facilities, including Brookhaven's 33-BeV Alternating- Gradient Synchrotron, CERN's 28-BeV Proton Synchrotron, and the USS R's 10-BeV machine at Dubna.

From to Bevatron director Edward Lofgren headed a group of scientists and engineers in planning a major modernization of the facility, with assistance from Walter Hartsough, who was in charge of operations at both the Bevatron and Bevalac for many years. The machine was shut down in July, for the improvements, and subsequently reopened in February, (Figs. 21, The modifications were made in the following five major areas: 1) Proton Injection System. A completely new proton injection system was installed for increased beam intensity; it consisted of a Cockroft-Walton ion gun and a 19-MeV strong-focusing linear accelerator (Figs.

23 and The new injector was capable of supplying at least 20 times more protons to the Bevatron than the old injector; the higher beam intensity was both more efficient (because of greater opportunities for beam-sharing and simultaneous experiments) and opened the possibility of the study of rare events. 2) External Proton Beam Facilities. An external proton beam facility was added allowing a beam to strike a primary target outside the machine (Fig. previously, a target had to be placed inside the accelerator for an experiment. To study particles striking an internal target, particle detectors and other equipment had to be set up in the cramped and inaccessible hub area of the machine.

The extraction of the primary beam from the accelerator allowed targets to be placed within the large experimental area outside the Bevatron. The other advantage of the external proton beam was that particles with extremely short half-lives would survive long enough to emerge from the accelerator and reach the detectors. In a machine with an internal target, these short-lived particles would not survive long enough to hit an external particle detector. In there was a further improvement in the extraction of proton beams through development of an External Proton Beam Facility. This facility, completed in was built as an addition to the original Bevatron Building.

It provided square feet of new floor space and allowed simultaneous service of several experimental targets with up to eight secondary target beams. 3) Concrete Shielding. Tons of new concrete shielding were added to the Bevatron to compensate for the increased beam intensity and to control background radiation levels (Fig. The original wooden shield was a partial wall on the south and west sides. As the beam increased, shielding was added to complete the wall on all sides. Some of the original shielding was 1-foot-square redwood timbers from a dismantled bridge.

These were fabricated into a ceiling shield, thereby shielding the control room, and used to create shielding-houses for the experimenters (Lambertson, In the concrete shield ring surrounding the accelerator was increased to a uniform thickness of 10 feet- Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 22 creating a concrete igloo-style housing. Experimental equipment was placed at the hub, and a new 7-foot-thick ceiling was built over the entire accelerator. The new shielding was supported by steel beams sunk in an underground tunnel directly beneath the magnet. The new shielding was expected to reduce background radiation to of the previous level.

This enabled scientists to undertake many experiments not previously possible because of interference from background radiation; it also reduced the necessity for special experiment- shielding houses, freeing space for offices or other functions. 4) Movable Targets. The increased beam intensity raised residual radiation levels inside the Bevatron tank; whereas previously, routine maintenance had been undertaken by workers actually entering the machine's tank, now such access would have to be kept to a minimum. Pole-face windings and other troublesome parts were replaced, and internal targets were moved, by remote control. In the early years at the Bevatron, scientists and workers had entered the magnet gap in the Bevatron for inserting targets and making measurements.

Physicist Glenn Lambertson recalls the improvisation involved thusly, With less convenience a person could also roll through the gap itself on a special flat scooter-it was a hot trip both thermally and radioactively. My first job in the gap was that of measuring the pulsed magnetic field. We built a cart to carry the pickup coil; this was made of non-conducting and non-magnetic materials ... This contraption, trailing cables, was pulled through the quadrant with a rope. With some fussing, it did work and gave us the data to know the energy of that first beam on April 2nd (Lambertson, 5) Control System. The control system was completely overhauled to eliminate undesired beam-induced resonances.

The operator's job was made much easier through better displays and an improved beam control system. This enhanced the monitoring of several variables including strength of the magnetic field, the number of protons in the beam, and position of the beam in the tank. Particle Detectors Used with the Bevatron The new particle discoveries that took place at the Bevatron in the and were made possible not only through advances in accelerator design but through developments in particle detector technology. The Laboratory had not been a pioneer in particle detection methods or technology before World War II, but developed a strong instrument section after the war (Heilbron et al., Cloud chambers had, since the enabled physicists to produce visual images of subatomic particles.

Two electronic counting detectors, scintillation and Cerenkov counters, were introduced about and were used in the first Nobel Prize-winning experiment at the Bevatron-the discovery of the antiproton. Scintillation counters involved the visual reading of flashes made by alpha particles striking fluorescent Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 23 screens; Cerenkov counters tracked the Cerenkov radiation emitted by a charged particle traveling through a substance at a velocity faster than the speed of light. The bubble chamber, invented by physicist Donald Glaser in and improved by Berkeley Lab physicist Luis Alvarez, was a visual detector that showed particle tracks in liquid hydrogen.

The liquid in a bubble chamber is heated above its boiling point, but is prevented from boiling by high pressure in the chamber. If that pressure is released for a very short time and then reapplied, the liquid still does not boil. However, if a charged particle passes through the chamber while the pressure is released, the resulting ionization leads to the formation of a string of bubbles along the path of a particle. This string of bubbles is then photographed to produce a picture of the paths or tracks of the charged particles in their passage through the chamber. (Barklow and Perl, Not all bubble chambers used liquid hydrogen. A UCRL team led by Wilson Powell and Robert Birge worked with propane bubble chambers.

Glaser won the Nobel Prize in Physics in for his invention of the bubble chamber. He was a UCRL scientist at the time of the award, but the invention had been made when he was a graduate student at the University of Michigan. The first bubble chamber at the Berkeley Lab, built in was 1.5 inches in diameter; by a 10-inch chamber was in use at the Laboratory (Fig. A 72-inch bubble chamber, the largest built up to that time, was completed in March, at a cost of $2 million with an additional expense of $1 million for a computer. This was the first giant bubble chamber, and a prototype of the large liquid hydrogen bubble chambers later used in high-energy physics all over the world.

The chamber, weighing 240 tons (not including its refrigeration system) was housed in a new 7500-square-foot building (Building 59) adjacent to the Bevatron (Fig. By bubble chambers had become the "foremost detectors of particles from high-energy accelerators," replacing the cloud chambers, counters, and nuclear emulsions that had been used as standard detectors of ionizing particles during the (Bradner, Heilbron et al., Ritson, Galison, Riordan, Bradner, W.A. Wenzel, working in Edward Lofgren's group at the Bevatron, introduced spark chamber detectors at the Laboratory. Spark chambers, first used in consist of an arrangement of parallel, electrically charged metal plates.

A charged particle passing between the plates causes the discharge of a series of sparks from one plate to another; when these sparks are photographed, they show the track of a particle passing through the chamber. Muon and electron tracks, for example, can be distinguished from each other using this method because of the observable differences in particle mass (Bernstein, By the early particle detectors at the Laboratory had achieved a status almost as great as accelerators themselves, and groups specializing in different forms of detector technology were organized at the Laboratory. George Trilling and Gerson Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 24 Goldhaber specialized in nuclear emulsions.

Donald Gow, who had assisted Alvarez in pioneering bubble chamber development and served as project engineer for several Rad Lab chambers, headed the team on bubble chambers (Fig. Hugh Bradner was in charge of data analysis development; H. H. Heckman's group focused on photographic problems; David Judd ran the electronic computers section. "Particle detection in the age of the bubble chamber came to resemble factory production. Other institutions followed the Rad Lab's lead" (Heilbron et al., The 72-inch bubble chamber was removed in December, after being in operation for 7 years and nine months. It was rebuilt and enlarged to 82 inches, and reinstalled at the Stanford Linear Accelerator. The 72-inch bubble chamber was subsequently returned to the Lab and is currently on display.

The Bevatron Transformed: The Bevalac The focus of this section of the report is on the Bevalac, a hybrid facility created in when the Bevatron was connected to a linear accelerator known as the SuperHILAC. A detailed account of the SuperHILAC and its predecessor, the HILAC, during the years before is beyond the scope of this report, but a brief review is included here as background for the history of the Bevalac. As will be discussed, the research role of the Bevatron was transformed by modifications permitting the SuperHILAC to inject heavy ions into the Bevatron. The HILAC, or Heavy Ion Linear Accelerator, was opened at the Laboratory in April, to study heavy ions-ions heavier than helium.

The HILAC, and a similar machine at Yale University, were the first accelerators built specifically for heavy-ion research. The basic elements of the HILAC were a Cockroft-Walton generator and two Alvarez linacs (linear accelerators) separated by a narrow space: In the first section the ions are accelerated to about 1 MeV /nucleon and, between the sections, electrons are stripped by passage through a thin foil of beryllium oxide; the ions then enter the second section where they are accelerated to full energy. (Blewett, The HILAC incorporated technology developed for the MTA Mark I; it made possible acceleration of nuclei as heavy as argon (element 18) to energies up to 10 MeV per nucleon.

Among the many achievements of a team headed by Glenn Seaborg and Albert Ghiorso were the synthesis of the elements nobelium ( and seaborgium In while Glenn Seaborg was serving as chairman of the AEC in Washington, Albert Ghiorso led a team that synthesized the element named lawrencium in honor of Ernest Lawrence, founder of the Laboratory (Heilbron et al., Hubbard, Blewett, Grunder and Selph, The HILAC was modified and upgraded in and again in A major modification, in warranted a new name for the machine, the SuperHILAC. A new ion source enabled the machine to accelerate beams of all ions up through krypton (an inert, monoatomic gaseous element, present in very small amounts in the atmosphere). Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 25 BEVALAC:

The Idea and Early Development

Plans for the upgrade of the HILAC to the SuperHILAC had originally included two improvements: capacity to produce beams of extremely heavy ions of low energy for nuclear chemistry research; and use of the SuperHILAC as an injector for a biomedical synchrotron for biomedical research 1968e:55). The second part of this plan-the biomedical research program-was ultimately sacrificed. The idea of combining the Bevatron with the SuperHILAC was originally conceived as an attempt to restore the biomedical program and to explore the potential of heavy- ion beams in cancer therapy. Albert Ghiorso, a nuclear chemist at the SuperHILAC who originated the idea for the Bevalac, explains, But now [with the SuperHILAC] we had no high energy capability at all.

I had been forced to abandon the biomedical people and I felt guilty about it. Ghiorso considered the idea of a further modification to SuperHILAC to raise the output of the machine to high energies for biomedical research, but was told it would be prohibitively expensive with available technology. (Ghiorso, Ghiorso, in proposing the Bevalac idea, was also influenced by another important factor. The Bevatron, superseded by more powerful accelerators at other research institutions, was already slated to be shut down.

This proposal would give it a new research program (Ghiorso, Heilbron et al., LaMacchia, Ghiorso's idea for the connection between the two machines was to use the SuperHILAC as a heavy-ion source and injector for the Bevatron to combine the best features of both machines-the heavy-ion capability of the SuperHILAC and the high- energy capability of the Bevatron. Ghiorso recalls that his inspiration for the idea of the Bevalac was a map showing the proximity of the Bevatron to the SuperHILAC, situated approximately 500 feet uphill. I remember returning from the Accelerator Conference at Chicago and talking to [Frank Selph] about his progress. He happened to have a map of the hill showing the various locations of the tunnels where he was thinking of placing his linac.

I noticed that the Bevatron was not very far away from the SuperHILAC and I suggested, somewhat facetiously, that maybe we should consider injecting our beam into that machine! Although I made the remark somewhat in jest I said that we should calculate whether that was at all possible. I thought that someone might ask about such a scheme because the Bevatron was on the list to be shut down within a year or so. Within a few minutes Frank had calculated that the idea was indeed feasible and the Bevalac was born. Ed McMillan Director] was one of the first persons that I went to with our idea. His reaction was typical of him, didn't I think of that!" (Ghiorso, Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 26 Funding for the Bevalac was secured through the efforts of Laboratory chemist Glenn Seaborg, who had just returned to LBL after several years as chairman of the AEC: We still had to worry about getting the funds for the 2M$-transfer line to carry the SuperHILAC beam down to the Bevatron. Although he had just stepped down as Chairman [of the AEC] and had returned to Berkeley, Seaborg still had lots of influence. He called one of the regents of U.C., who in turn called Caspar Weinberger, the Director of OMB [Office of Management and Budget] under Nixon, and persuaded him to place the needed transfer line into the budget. The rest is history!

Under the very capable hands of Ed Lofgren and Hermann Grunder the Bevalac became a great and successful accelerator. (Ghiorso, Ghiorso had accurately predicted that the pulse and energy characteristics of the SuperHILAC beam were ideally suited for injection into the Bevatron. The Bevalac achieved its first beam in August, By it was capable of accelerating iron ions, the heaviest ions accelerated in a high-energy beam at that time. Even after the Bevalac facility was in operation, however, both the Bevatron and SuperHILAC continued to operate independently at times; each accelerator maintained its own injectors and developed separate experimental programs. The Bevalac ushered in a new era of research at the Laboratory.

The focus of the Bevatron had previously been in particle physics research; only comparatively light particles [e.g. mesons, protons, electrons (an elementary particle that is a fundamental constituent of matter, having a negative charge, and existing independently or as the component outside the nucleus of an atom), alpha particles, deuterons] were available to experimenters at high energies. Heavy nuclei like nitrogen could be accelerated only to relatively low energies, in linear accelerators like the HILAC. The Bevalac was ultimately capable of accelerating all of the naturally occurring heavy nuclei.

Heavy ions injected into the Bevatron from the beam transfer line originating at the SuperHILAC, were accelerated to 2.1 BeV per nucleon for applications in nuclear medicine, nuclear physics, and cosmic-ray experiments. The beam research time at the Bevalac was divided so that one third was for biomedical use and two thirds were for nuclear science experiments-including a wide range of fields such as elementary particle production with heavy ions, nuclear fragmentation, cosmic-ray simulation, and atomic physics.

(Alonso, The Bevalac was the only research facility in the world capable of accelerating to high energies the nuclei of all the elements of the Periodic Table-from the lightest element, hydrogen, all the way up to uranium, the heaviest of the naturally occurring elements (Goldhaber, LaMacchia, Grunder and Selph, The Bevalac, (in conjunction with the 88-inch cyclotron also at the Rad Lab) became the country's leading facility for heavy-ion research, drawing scientists from universities and laboratories throughout the United States, and from all over the world, including China, Japan, Germany, and Israel (Heilbron etal., Kapa, Kapa, Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 27

Bevalac Design

The connection between the SuperHILAC and the Bevatron was made through a 550-foot meter) transfer line, that served as a conduit for a heavy-ion beam traveling downhill from the SuperHILAC to the Bevatron. The transfer line lost 140 feet in elevation, before bending and continuing the remaining 300 feet horizontally in the 50-MeV proton injector line. One hundred twenty-five feet of the hillside line was actually underground, contained in a steel liner pipe.

The line used 12 bending magnets and 30 quadrupole magnets to guide the beam along the way; transmission of the beam was tuned through computer monitoring and control Alonso, The Bevalac system was developed from through under the direction of Edward Lofgren, Division Leader of the LBL Accelerator Division, and Hermann Grunder, a specialist in accelerator design and later Bevalac Group Leader.

In addition to the beam line, the Bevalac required four modifications of the existing facilities: 1) Additional rf cavity in the SuperHILAC to provide for energetic ions for injection 2) Control room in the Bevatron exclusively for biomedical research 3) Two experimental caves in the Bevatron for biological and medical work 4) Animal handling and tissue culture facility in the Bevatron The SuperHILAC had two injectors that could provide heavy ions for its own experimenters and for Bevalac researchers at the same time. The first injector, named Eve, was designed to produce ions up to argon, mass 40 on the periodic table. The so- called Adam injector could inject ions as heavy as lead. A third injector named Abel, was added in to provide ions up to uranium 1981a:4).

An improvement program at the Bevalac-a new injector for the SuperHILAC, an upgrading of the transfer line, and a new high-vacuum system in the Bevatron-enabled the Bevalac in to become the first machine in the country capable of accelerating uranium to nearly the speed of light 1981a:4; A new particle detection system was developed at the Bevalac for heavy-ion research. The Heavy-Ion Spectrometer, or HISS, was installed in on the east side of the Bevatron's main experiment hall, and was designed for multiparticle experiments, rather than the single particle experiments that had predominated before that time. The project scientist was Peter Lindstrom; Doug Greiner was group leader with overall responsibility for HISS detectors; Hank Crawford was in charge of HISS facilities.

HISS was a system, or workbench, where experiments could be arranged quickly and inexpensively, and where many experiments could be performed simultaneously. The system included a large superconducting dipole magnet, two versatile beam lines, a flexible computer system, and a large experimental cave area, but the heart of HISS was a huge magnet 15 feet high, 21 feet wide, 10 feet deep and more than 1 million pounds in weight. A Laboratory report extolled the virtues of the HISS system. This powerful magnetic field will do for subnuclear particle beams what a prism does for light-divide and separate out different components, thereby providing a spectrum for viewing and analysis ...but HISS will not Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 28 include the instrumentation found in a classic spectrometer. Researchers using HISS will provide their own particle detectors and some specialized instrumentation during experiments.

Bevalac Biomedical Facility

In the Bevalac was established as a national accelerator facility for biomedical heavy-ion research funded by the U.S. Energy Research and Development Administration (ERDA). Under the terms of the funding, the beam was to be available to all potential users throughout the country. The Bevalac Biomedical Facility, which opened in the Bevatron in united the biological and physical sciences in a program to use heavy ions clinically for diagnostic and therapeutic radiology. It was specifically designed for tumor, tissue, cellular, molecular, neural, developmental and space radiobiology, radiography, and radiological physics. It included a separate control room, three irradiation caves, and two preparation rooms.

Biomedical programs included basic research on cancer, radiological and chemical studies, and research on the nervous system, in addition to cancer therapy and medical diagnosis (Alpen and Lothrop, Cornelius A.

Tobias, a pioneer in early cancer therapy research at the Laboratory, noted in that the Bevalac was the "only accelerator in the world capable of producing heavy ions with substantial beam penetration qualities that are suitable for medical applications in humans" (Tobias, The best ions for biological and medical work range from neon (element 10) through iron (element After being generated in the SuperHILAC, these heavy ions were steered by magnets through a vacuum line into the Bevatron where they were further accelerated to higher energies and then directed to one of three experimental rooms- the Radiological Cave, the Biological Cave, or the Minibeam Room. The Minibeam Room was located on top of the shielding roof directly above Channel II.

The beam was brought up through a hole in the roof blocks at an angle of 27 degrees and ran parallel to an inclined optical rail system inside the Minibeam house. This facility was designed for low-energy, low-intensity operation with extremely fine beams for microscopic radiobiological work and microsurgery (Alonso, Accelerated heavy ions are particularly well suited to biological and medical research and therapy. They penetrate deeply and deposit their energy abruptly as they stop in a target, which makes them especially appropriate for diagnosis and treatment of many diseases, including some types of cancer. Most of the destructive force of the beam is concentrated at its stopping point in the tumor without damaging the surrounding healthy tissue.

This is in contrast to conventional radiation therapy; x-rays, for example, deliver a dose that steadily decreases with depth, so that surface tissue is more likely to be damaged than the deep-seated tumor Joseph Castro, who directed the biomedical program at the Bevalac, has explained that, There are two real advantages for this kind of radiation, the first of which is that since it's a charged particle, it can be much more precisely delivered than the standard kinds of high energy x-ray treatment that you would Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 29 commonly find in a hospital. And that precise delivery means a greater effect on the tumor and less side effects in terms of normal tissues around the tumor.

The other big advantage is the biology of these particles, that is the biological effects are greater, and therefore, there's a better chance of killing tumor cells with the Bevatron radiation than with the standard kinds of radiation. (Quoted in LaMacchia, The patient therapy program at the Bevalac began on a small scale in the spring of By patients were treated four days a week. Physicist Jose Alonso headed the biomedical team at the Bevalac in with patient monitoring by Berkeley Lab radiotherapists and local hospitals Dr.

Castro described the treatment of patients in the Bevalac Biomedical Facility in detail: So the patient would typically be seated in [a] chair and in a mask, and the radiation beam came from the Bevatron, where it was accelerated into this room in a horizontal fashion, and would pass through a number of devices to shape the beam to determine how deeply it would penetrate, and then through these measuring devices to be sure that we had the right dose and energy, and finally intersect the patient, coming to rest in the tumor. (Quoted in LaMacchia, BEVALAC

Research in Nuclear Chemistry and Physics

The Bevalac was the only laboratory in the country capable of simulating the high- energy heavy-ion component of primary cosmic rays; this component of primary cosmic rays consists mostly of hydrogen nuclei (protons) but also some heavier elements that are always streaming toward earth from outer space. Relatively little was known of primary cosmic rays, because naturally-occurring cosmic rays interact with gas molecules in the upper atmosphere and form secondary particles before reaching the earth. The Bevalac played an important part in the NASA space program, studying how cosmic radiation reacts with matter. Instruments were exposed to beams to evaluate sensitivity to cosmic radiation.

Biophysicists Stan Curtis and Aloke Chatterjee developed models for assessment of the health risks to astronauts due to heavy-ion exposure during long-term space missions. Biophysicist Cornelius Tobias conducted controlled experiments to test the veracity of astronauts' reports of seeing flashes of light in outer space. He exposed himself to a beam at the Bevalac and observed a visual phenomenon never before seen on earth. "You see visual flashes," he recalled. "It is an exhilarating sensation. It is as though you are looking into the universe itself." In the late experiments at the Bevalac produced the world's first data on central collisions of energetic beams of heavy ions and heavy-element targets.

In these experiments, a beam of heavy ions such as neon 20 was accelerated to near the speed of light and steered to collide with a very heavy target nucleus such as uranium. The Art Poskanzer/Hans Gutbrod Group, which included both nuclear chemists and nuclear physicists, measured such reactions in their scattering chamber at the Bevalac, and worked on a description of the reaction known as the fireball model. According to this Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 30 model, nucleons in the area of impact momentarily fuse together, forming a kind of nuclear fireball, which then decays in an explosion of particles. The fireball reached a temperature of 50 MeV, which was believed to be the hottest nuclear matter ever seen at that time.

Art Poskanzer noted that "it took both the physicist's and the chemist's point of view to come up with the fireball model" In the late and early scientists at the Bevalac sought to identify the mysterious substance known as quark matter by studying the particles produced in heavy-ion collisions. Quark matter is a form of matter-predicted but never yet observed-that consists of free quarks (the ultimate particle-like constituent of matter) and gluons (the carrier of the force that binds particles together) in a kind of nuclear soup. Quark matter is thought to have been the dominant state of matter at one point shortly after the Big Bang, and may still be present in the cores of neutron stars left over from exploding supernovae.

A major current goal of nuclear science is to create and study quark matter in the laboratory by colliding heavy nuclei (ions) at high energies. (Goldhaber quoted in In addition, the LBL Nuclear Science Division's dilepton spectrometer team led by Lee Schroeder and Chuck Naudet studied certain very rare particles produced in heavy-ion collisions. These rare particles, which occur only once in a million events, provided "a unique view of the earliest moments of collisions between heavy ions" (Goldhaber quoted in ). In a typical DLS experiment, the researchers varied factors like the mass of the projectile and target nuclei, the energy of the beam, and the density reached during the collision.

These variations were reflected in the mass of the intermediate particle that linked the primary pions created in the collision to the electron/positron pair that was eventually detected. The spectrum of these masses provided information on how the pions propagated in hot, dense, nuclear matter. The first important DLS observation, in was that the pion annihilation process is the main mechanism for electron pair production in heavy-ion collisions at high mass (Goldhaber quoted in 1). Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 31 Bevatron Closure The Bevatron/Bevalac research complex closed in February, 39 years to the week after the first subatomic particle beam was circulated.

The decision was made by DOE after several years of deliberation, and in spite of last-minute appeals by NASA, which sponsored the facility's cosmic-ray research. An article in the Berkeley Lab periodical Currents, described the decision as a primarily political one, in a period of budget shortfalls. "The Bevalac was, in essence, a victim not of scientific obsolescence but of today's adverse economic climate.

The money could not be found to fund a Berkeley Lab proposal to keep the accelerator running for ground-based cosmic-ray experiments that would help assess radiation risks to astronauts on deep-space missions" Judith Goldhaber, science writer for Berkeley Lab publications, summarized the achievements of the Bevatron/Bevalac, emphasizing the extraordinary versatility that allowed the facility to flourish as long as it had. In the past, Bevalac was often snatched from seemingly inevitable closure, to be reborn each time into a whole new productive chapter of its career. But now it seems to have finally used up all of its nine lives.

Since its commissioning almost 40 years ago, the venerable particle accelerator has made major contributions to four distinct areas of research: high- energy particle physics, nuclear heavy-ion physics, medical research and therapy, and space-related studies of radiation damage and heavy particles in space. As the Bevatron/Bevalac neared the end of its usefulness in each of these fields, the area of research it had pioneered moved to other facilities around the nation. Thus, particle physics continues at accelerators such as Fermilab's Tevatron, [and] SLAC's colliders ...

Heavy-ion nuclear studies will be the major focus at the new Relativistic Heavy Ion Collider (RHIC) at Brookhaven, and experiments in heavy-ion therapy led to design of dedicated medical accelerators such as the Proton Cancer Treatment Center at Loma Linda University Medical Center, and the proposed proton therapy facility at the UC Davis Medical Center. The original version of the accelerator, the Bevatron, has been called (by physicist Ed Lofgren, who was in charge of its operations from until his retirement from the position in "the last of the great accelerators built in .. .'the Lawrence style,' ... durable and adaptable. That's why it's not surprising that the Bevatron has endured and adapted so well over the years." Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 32 Overview of the Historic Significance of the Bevatron 0 nly the highlights of the many years of scientific work at the Bevatron can be described here. Although many discoveries relating to atomic structure and function were made at the Rad Lab, the focus for this discussion will be on Nobel Prize-winning experiments and some of the significant persons associated with the Bevatron.

Nobel Prize-Winning Research ANTIPROTONS: NOBEL PRIZE TO EMILIO SEGR~ AND OWEN CHAMBERLAIN, The existence of the antiproton, the antiparticle of the proton (nucleus of the hydrogen atom) had been theorized since It is now known, in relativistic quantum theory predictions, that every subatomic particle has an antiparticle, identical in every respect except that all charge-like properties (electric charge, strangeness, and charm) are opposite (Barklow and Perl, Antiparticles are bits of matter that have properties exactly opposite to their counterparts in ordinary matter. They do not normally exist in the ordinary world of matter, and if produced they exist for only a short time, for when they collide with ordinary particles they are annihilated with them.

The result of the annihilation is the creation of other particles that usually decay quickly and dissipate into energy. At the beginning of when scientists at the Bevatron began the search for the antiproton (the negative proton) the division of the particle panoply (a complete covering or array of something) into particles and antiparticles had not yet been fully established, and some physicists doubted whether the antiproton existed (Riordan, However, most physicists at Berkeley Lab "were firmly convinced that antiprotons were being created in the nuclear debris formed when protons in the Bevatron beam struck a target of copper (Figs.

The trick was to catch and detect them" (Goldhaber, The Bevatron, capable of boosting protons to energies of 6 BeV, was the only accelerator operating in with enough energy to produce antiprotons. Different teams of scientists at the Bevatron entered into a kind of competitive race to find the antiproton (Fig.

Physicist Edward Lofgren played a substantial part in the process, both as leader of one of the teams and as Bevatron director responsible for coordinating and scheduling the use of the machine (Heilbron et al., A team of scientists led by physicists Owen Chamberlain and Emilio Segre, using three magnetic quadrupole lenses to focus antiprotons onto electronic counters- scintillation counters and Cerenkov counters-found clear evidence of a negatively charged particle with exactly the same mass as a proton-the antiproton (Fig. Two members of their team who made important contributions to the discovery were Clyde Wiegand (Fig. and Thomas Ypsilantis (Riordan, Heilbron et al., Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 33 This first discovery of the antiproton through the measurement of its mass was quickly confirmed by a team led by Eduardo Amaldi in Rome and Gerson Goldhaber at Berkeley Lab, who found the tracks of the collisions of protons and antiprotons in photographic emulsion plates. Photographic emulsions are stacks of photographic film that are exposed by the ionization tracks of energetic charged particles. The image of the tracks can be observed when the film is developed (Goldhaber, Westfall, Segre and Chamberlain won the Nobel Prize in for their experiment. Chamberlain discussed the importance of the discovery in a retrospective essay published in "In assessing the impact of the discovery on physics, I would say it was certainly no surprise.

Most theorists predicted that the antiproton was there to be found when conditions were right. Still, the discovery cleared the air: It allowed people to proceed more confidently into a rewarding future" (Chamberlain, In July-August, about a year after the discovery of the antiproton at UCRL, a second antiparticle, the antineutron, was discovered by another UCRL experimental group-William Wenzel, Bruce Cork, Glenn Lambertson, and Oreste Piccioni.

DISCOVERY OF THE RESONANCES: NOBEL PRIZE TO LUIS ALVAREZ, "Perhaps the farthest reaching of the discoveries made with the Bevatron were the so-called 'resonances' or energies at which fleeting combinations of particles occur" (Heilbron et al., o- Resonances are particles whose lifetimes are on the order of 1 23 second-too short to leave visible tracks using the conventional instruments of this period. Such particles travel about a trillionth of an inch before decaying into two or three other particles. Bubble chamber photographs showed only a spray of tracks at the point where the resonance was formed. The first resonance was discovered by Enrico Fermi in Chicago in Physicists subsequently undertook analysis of these spray patterns.

The first resonances found at Berkeley were a hyperon (any of several elementary particles having a mass between that of a neutron and a deuteron) and two pions, in The Berkeley group, working with the 15-inch bubble chamber, then found the first kaon resonance and another hyperon resonance.

Luis Alvarez's 72-inch bubble chamber was the most advanced tool for detection of resonances in the early The first vector meson, K*, was discovered at Berkeley Lab in By a pion-pion resonance, and a three-pion resonance led the way to a new era of resonance discoveries in the (Riordan, Alvarez won the Nobel Prize in physics in for "the discovery of a large number of resonance states, made possible through your development of the technique of using hydrogen bubble chambers and data analysis." The award was given in recognition of two related contributions: 1) Alvarez's development of the bubble chamber for observing high-energy atomic interactions-the use of large liquid hydrogen bubble chambers and computer-linked data processing systems; 2) Alvarez's involvement in finding 18 of the resonances, which were either discovered or codiscovered in film from one of the two big Rad Lab bubble chambers, the 15-inch or the 72-inch.

Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 34 At a press conference at the time of the announcement of his Nobel Prize, Alvarez gave full credit to Donald Glaser, the inventor of the bubble chamber, and to the team who worked with him, including Donald Gow, who "played the greatest role in the development of the hydrogen chambers," Frank Solmitz and Art Rosenfeld, who led the computer development for his group, and Paul Hernandez, who was the chief engineer of the 72-inch bubble chamber. Among Alvarez's students in the pioneering bubble chamber work were M. Stevenson and Frank Crawford (Stevenson, 1993a, Alvarez recalled the thrill of his pioneering work at the Bevatron.

The early days at the Bevatron were unbelievably exciting; we were repeating and extending the work that had been done by cosmic-ray physicists in the past 20 years. But our 'cosmic rays' traveled horizontally instead of vertically, were billions of times more intense, and ended up in our bubble chambers, where we could take a good look at them! (Quoted in Goldhaber, THEORY OF PARITY NONCONSERVATION: NOBEL PRIZE TO TSUNG-DAO LEE AND CHEN NING ("FRANK") YANG, INDIRECT

Connection to Bevatron

Until almost all physicists believed in the conservation of parity, or the mirror symmetry between left and right. Before the Lee-Yang paper, it had become almost a credo that mirror invariance (parity conservation) is an a priori property of the laws of nature rather than an hypothesis to be tested by experiment" (Telegdi, Parity symmetry had been used to make predictions in atomic and nuclear physics. Even after initial experiments raised questions, "in many laboratories, both in the United States and in Europe, parity violation was considered too wild a hypothesis to warrant an all-out experimental effort" (Telegdi, Lee (of Columbia University) and Yang (at Princeton University) found that parity was sacrificed in some weak interactions involving mesons and hyperons.

While working as visiting scientists at Brookhaven National Laboratory, they correctly predicted in that the weak nuclear force, which causes radioactivity and the slow decay of many subatomic particles, violated parity, the symmetry of left and right. This was the "first known example of a lack of symmetry in nature" (Gerson Goldhaber, quoted in Goldhaber, Parity symmetry is therefore only observed in the strong nuclear force, which holds atomic nuclei together, and in strong nuclear interactions (Heilbron et al., Riordan, Bernstein, Goldhaber, Scientists at the Bevatron made experimental observations of the subatomic particles, K mesons, that contributed significantly to the theory of parity nonconservation-that parity does not hold in some cases.

Physicist Gerson Goldhaber, who participated in this early work at the Bevatron, has described the contribution of Berkeley scientists. Two important observations emerged from these early studies of K mesons at the Bevatron. First, what had been believed to be two different kinds of K particles were found to be indistinguishable, even though one kind decays into two pions and the other into three. Dick Dalitz suggested Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 35 that the difference lay in their parity-right handedness or left handedness-and T. D. Lee and Frank Yang hit on the explanation: that parity was not being conserved in this decay.

(Quoted in Goldhaber, Dalitz, THEORY OF STRANGENESS AND THE EIGHTFOLD WAY: NOBEL PRIZE TO MURRAY GELL-MANN, A CAL TECH PHYSICIST, INDIRECT CONNECTION TO BEVATRON Berkeley emulsion groups contributed to Gell-Mann's identification of so-called strange particles that had novel isotopic spin assignments. "The positively charged K+ and the negatively charged K- turned out to have very different interaction properties, and this confirmed Murray Gell-Mann's suggestion of a new property of matter, strangeness" (Gerson Goldhaber quoted in Goldhaber, Gell-Mann introduced a new quantum number, the strangeness S.

"What took this scheme beyond mere taxonomy was Gell-Mann's imposition of an approximate conservation law, namely, that in all strong processes, the kind in which the strange particles are produced, strangeness is conserved" (Quote in Bernstein, Heilbron et al., Gell- Mann, ). Lawrence Radiation Laboratory physicists Sheldon Glashow and George Kalbfleisch discovered a new elementary particle, the Y*1 that provided important confirmation of Gell-Mann's theory of the Eightfold Way. This theory suggests that, The basic components of strongly interacting matter, the so-called 'elementary' particles, fall naturally into groups, or multiplets, of particles, with the majority of the particles arrayed in groups of eight called octets.

In the 'ground' state, there are four such octets, one collection often called a decouplet, and several singlets. Other particles that have been discovered are seen as recurrences of these particles at higher energy states. The importance of the theory, aside from the question of its theoretical validity, lies in the fact that it permits the prediction of yet undiscovered particles. In this sense, the 'eightfold way' scheme might serve modern physics for subatomic particles as the periodic chart of the chemical elements has served chemists in the past. Such a scheme would permit physicists to predict the properties of nuclear states of matter from a limited knowledge of the more familiar particles.

1963a:l) Scientists Associated with the Bevatron The following discussion classifies significant persons in two groups. In the first group are the Nobel Prize-winning physicists whose work is associated with the Bevatron; the second group is composed of the many scientists, engineers, and physicians who conducted important scientific work at the Bevatron and Bevalac, or who contributed significantly to the design and operation of the accelerator. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 36 Ernest Orlando Lawrence and Edwin McMillan Although their Nobel Prizes were not directly associated with the Bevatron or Bevalac, they played leading roles as Laboratory directors in the creation of the facilities.

Lawrence's invention of the cyclotron in and McMillan's idea of phase stability in were major scientific contributions that provided a foundation for development of the Bevatron. All of the people on the following list are physicists unless otherwise noted. All of them were (and many still are) on the Berkeley Lab staff. Nobel Prize winners directly associated with the Bevatron: Emilio Segre and Owen Chamberlain Jointly awarded the Nobel Prize in for their discovery of the anti proton in an experiment at the Bevatron. This experiment is described briefly in the Overview of the Historic Significance section in this record.

Luis Alvarez Won the Nobel Prize in for his development of the bubble chamber particle detector (originally invented by Donald Glaser) and for his role in finding 18 particle resonances with Rad Lab bubble chambers used in conjunction with the Bevatron. Many other researchers have been associated with the Bevatron/Bevalac.

The following are representative of the scientists and engineers associated with the Bevatron and Bevalac: Jose Alonso: Bevalac Director; nuclear physicist in Bevalac Biomedical Facility Robert Birge: Experimental work with propane bubble chambers Eleanor Blakely: Researcher affiliated with the Biomedical Facility William Brobeck: Engineer, Chief Designer of the Bevatron Joseph Castro: In charge of clinical medical program at Bevalac Bruce Cork: Member of team that discovered antineutron in worked on instrumentation and experiments from early period (Fig.

36) Ben Feinberg: Head of operations at the end of the Bevalac Albert Ghiorso: Nuclear chemist at HILAC who conceived idea for Bevalac Gerson Goldhaber: Experimental work with nuclear emulsions Donald Gow: Assisted Luis Alvarez in development of bubble chamber Hermann Grunder: Built the Bevalac and was head of Accelerator Division at the Rad Lab after Edward Lofgren's retirement Walter Hartsough: In charge of operations at Bevatron/Bevalac for many years Paul Hernandez: Assisted Alvarez with the hydrogen bubble chamber detector Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 37 Harry Heckman: Conducted first Bevalac experiments on projectile fragmentation Glenn Lambertson: Member of team that discovered anti neutron in worked on instrumentation and experiments from early period Edward J.

Lofgren: First director of Bevatron, leader of Bevalac development, Director of Accelerator Division at Rad Lab Shoji Nagamiya: Leader of the Japanese research group at the Bevalac Charles Naudet: Worked with Lee Schroeder on heavy-ion research Oreste Piccioni: Member of team that discovered anti neutron in Art Poskanzer, Hans-Georg Ritter, and Hans Gutbrod: Members of the team that discovered the directed flow of nuclear matter Wilson Powell: Experimental work with propane bubble chambers Howel Pugh: Scientific Director of the Bevalac for many years Stevenson: Member of Luis Alvarez's team in bubble chamber experiments Reinhard Stock: Leader of the German research group at the Bevalac James Symons and Hank Crawford: Conducted research using HISS (Heavy Ion Spin Spectrometer) lsao Tanihata: Discovered neutron halo in lithium Cornelius Tobias: Conducted cancer therapy research at Bevalac George Trilling: Experimental work with nuclear emulsions William Wenzel: Member of team that discovered antineutron in work on instrumentation and experiments from early period Clyde Wiegand: Member of the Segre/Chamberlain team that discovered anti proton Gordon Wozniak and Luciano Moretto: Investigated complex fragment emission of heavy ions Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 38 Architecture of the Bevatron Building T he terms Bevatron and Bevalac commonly refer to a complex of buildings and the machines inside them. The buildings and machines functioned together for common purposes, and in several ways the distinction between buildings and machines is blurred. At the same time, a natural distinction exists between buildings and machines. From the beginning, they were the concerns of two separate sets of designers and builders. Buildings were constructed under the building codes and other applicable laws of the State of California; building records have always been kept separate from machine and instrument records.

The purpose of this section is to discuss the chronology of building construction and to summarize the architectural features of the Bevatron. Construction History of the Bevatron Building Complex The buildings of the Bevatron/Bevalac, and associated buildings, which still exist are the Bevatron (Building 51, 51A, and 51 B), the HILAC (Building 71 ), and the Accelerator Design Building (Building Building 51 and Building 71 together comprised the main components of the Bevalac accelerator. (These buildings are described to provide the context of the construction history; however, we would like to note that only Buildings 51 and 51A are of historical significance.) Building 64 served first as a support building for the Bevatron and later for the Bevalac.

Building 59-no longer in existence-housed the bubble chamber and was one of several particle detection facilities built in the flat, open area adjacent to, and northwest of, the Bevatron. The area occupied by the Bubble Chamber Building was subsequently covered by the External Proton Beam Hall (EPB) B) in Building 59 was, at the time of its construction, the most prominent detection facility outside of the shelter of the Bevatron. After it was demolished, most subsequent detection facilities were inside the Bevatron complex (including the EPB), and lay largely on the machine-side of the machine/building divide. Other experiment buildings have been relatively small and unobtrusive.

The buildings of the Bevatron were frequently modified and expanded throughout their years of service from the early to February Since the Bevatron/Bevalac was closed in February some of the machines and other furnishings which the buildings housed have been removed. The history of the Bevatron and other associated buildings are introduced as a whole, and then treated separately below.

Building Site Characteristics

The Bevatron is located on a hill east of the campus of the University of California (Fig. 37) at Berkeley that was a large, sparsely developed area first assigned to the UC Radiation Laboratory in The Bevatron was built on an undeveloped piece of land called the Wilson Tract which had been allocated for the UC Radiation Laboratory. A contract for grading and drainage of the site was let in August, At the time the Bevatron was built, the principal building of the Laboratory was the 184-inch Cyclotron Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 39 (Gebhard, A comparison of the 184-inch Cyclotron and the Bevatron will illustrate the nature of the Bevatron Building. The Cyclotron was sited prominently so that it could be seen from the main campus and a wide area below.

It occupied a key spot on axis with the plan of the main campus, and its dome was designed to be compatible with the Beaux-Arts classical buildings on the campus. In its design and siting, the Cyclotron was symbolically powerful, expressing its relationship to the campus and established fields of learning to a wide public. By comparison, the Bevatron was situated below the Cyclotron on the hill so that it was barely visible from below (until the EPB hall was built in Its siting and design had no relation to the main campus plan. In appearance, it was a modern industrial building that could have been sited anywhere. BEVATRON BUILDING (BUILDING 51) Phase 1. Building 51, The Bevatron Building The Bevatron Building was designed by the San Francisco architectural firm of Masten and Hurd.

The earliest dated scheme was a drawing of September 9, A signed perspective dated December 10, indicates that there was a general approach to the building in place by that time (Figs. 38, A complete set of as-built drawings on file at the Berkeley Lab Facilities Department is dated June 6, The index to subcontracts of the Facilities Department of Berkeley Lab shows a contract let for construction in June (Fig. Construction photographs dramatize the difficulty of building on a hill (Figs. which was reached by a narrow, winding road, in a series of views of a truck hauling one of the 93-foot long cranes to the site. Photographs show the building as complete before the machines were finished (e.g.; Berkeley Lab Photo: Box 1, Book 1, No.

and illustrate the role of the building in the completion of the machines, with the winding of the magnet coil using the big crane. As built, the Bevatron consisted of a principal circular magnet room with a quarter- circle, two-story, shop-and-office wing along the south side of the circle, and a large rectangular mechanical wing tangent to the circle on the northeast (Fig. The circular magnet room is 220 feet in diameter and 40 feet high between the main floor and the bottom of two tiers of roof trusses. A pair of 30-ton cranes, mounted on crane rails at the center, and the circumference of the space were used to install and repair the magnet below and to handle later additions such as concrete shield blocks.

The 34-foot-wide shop-and-office wing included spaces designated for control room, electronic equipment and shops, and office space for researchers and engineers (Figs. The mechanical wing x feet) housed the fan room for cooling the magnet, the motor/generator room for providing power to the magnet, and miscellaneous shops. Its exterior is clad in corrugated transite panels and bands of steel sash and louvered ventilators. Under a separate design and contract, a cooling tower was built outside the circle in the area between the shop-and-office wing and the mechanical wing. This was in place by May It was demolished in as a collapse hazard. Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 40 Another contract in October was for construction of a ring of foundations to support heavy concrete shielding around the magnet. This was a ring 10 to 13 feet wide of concrete caissons with an inner radius of 60 to 65 feet. The designer was Robert A. McGuire of Huber and Knapik, engineers. Little is known about the design process or program apart from what can be inferred from the drawings and the building itself. William Brobeck, designer of the Bevatron machine, was not involved in the design of the building. The architects, Masten and Hurd, were respected designers of public schools and other school buildings and had worked for the University of California on other projects (Figs.

49, Although the design of the building is unique among industrial buildings in general and accelerators in particular, it is characteristic of industrial buildings of the period, in that its form was generated from its very specific functional needs. It was designed from the inside out-without preconceptions about its shape. It provided shelter for its machines, space for circulation of personnel, and room for future expansion-all in a setting of natural light and adequate ventilation (Figs. Phase 2. Building 51 Addition, Building 51A. The Building 51 Addition was an expansion of the principal circular magnet room of the Bevatron on its northwest periphery (Fig. It ran one-third of the way around the circle to the south from the mechanical wing.

It was 65 feet wide except at the junction with the mechanical wing where it included a new generator room, and was about 80 feet wide. It was designed together with Building 59 to the northwest, to which it was linked by a heavy concrete pad. Both buildings were designed by the San Francisco firm of Milton T. Pflueger, Architect, in plans dated February 11, Huber and Knapik were structural engineers, and Buonaccorsi and Murray were mechanical and electrical engineers. A contract was let for construction in February The Building 51 Addition was a steel-frame structure clad in corrugated transite panels with bands of steel sash windows, to match the original Bevatron Building. Except for the new generator room, it was about 40 feet high from the floor to the bottom chord of the roof truss.

The roof was supported by a Pratt truss so that there was a single, slightly curving, open space below. This space was served by a 30-ton crane that was curved to fit the exterior curvature of Building 51. Also in this period, new cooling towers were built in the area just outside the circle between the shop-and-office wing and the mechanical wing. These were built under contracts let in May and April The designation Building 51A has come to include both this addition and a smaller addition in described below. Phase 3. Major Bevatron Improvements A group of substantial modifications to the Bevatron were undertaken in to commonly referred to as Major Bevatron Improvements. The architectural modifications required to accommodate these changes were primarily inside-many of them underground.

The major areas of change in the building were initially to provide additional shielding for the magnet, to accommodate a new injector and an external Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 41 beam, to remodel the north experimental area, and to build the west experimental area addition, and a five-story south addition. All but the south addition were realized. To accommodate complete shielding of the magnet, new walls had to be built inside and outside the magnet ring which would be spanned with a roof, so that the magnet was completely enclosed by massive blocks of concrete. Foundations for the outer shielding walls had been built in and strengthened in New foundations had to be built for the inner shielding walls.

Tunnels and ducts were built underneath the shielding which required additional strengthening and reconstruction of the inner wall area to maintain the inner crane rail above. This area was referred to as the new Center Structure, and more commonly as the Igloo. The shielding foundation and support structures were designed by Huber and Knapik. Moran, Proctor, Mueser and Rutledge of New York, Consulting Engineers, and Keller and Gannon, Mechanical Engineers of San Francisco were associated on the project. The center structure was designed by Earl and Wright of San Francisco.

This work was performed under a contract let in July To accommodate a new injector, the original electricians and maintenance machinist's shops in the mechanical wing of the building were combined into a single space, and new foundations were provided. For the construction of an external beam line beyond the northwest edge of the building a foundation for shielding was built. This work was all designed by the same team that designed the shielding and was built between May and October The north experimental area, in the Building 51 Addition just west of the mechanical wing, received new foundations, new partitions including a soundproof wall for insulation from the motor/generator room, and a heavy duty floor.

This work was performed under a contract let in May The West Experimental Area Addition (Building 51A) was designed by Earl and Wright and was built under contracts let in July and June This expanded the Building 51 Addition of described in Phase II above, around the circle two bays of the circle) until it met the original shop-and-office wing. Together with the Building 51 Addition, this was designated as Building 51A. Phase 4. External Proton Beam (EPB) Hall, Building 51 B The External Proton Beam Hall was designed by Earl and Wright, Consulting Engineers of San Francisco, in several stages.

The first stage was the External Beam Craneway, whose design is shown in a set of as-built drawings dated December 14, A contract for this work was let in December The design for the External Beam Craneway Roof is shown in a set of drawings dated August 19, The External Beam Craneway was built around and over Building 59 which was demolished according to drawings dated January 30, The design for the EPB hall siding is shown in a set of drawings dated July A contract for this work was let in July The EBP Hall projects northwest from the edge of that portion of the Bevatron designated as Building 51A. It is a rectangular steel-frame structure measuring about 290 by 144 feet and 74 feet high. It is 52 feet high from the floor to the bottom chord of Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 42 the system of roof trusses. The roof is supported by a grid of Pratt trusses. The EPB hall is open for 21 feet around its base, and enclosed by large metal and plastic wall panels above. These panels measure 53 by 30 feet and are blue-green in color. The interior is a large craneway with a clearance of feet. It was only with the application of siding to the EPB Hall that any portion of the Bevatron became conspicuous from the City of Berkeley. The main floor level for both buildings is at an elevation of 710 feet above sea level. The Bevatron is about 68 feet to the top of its conical roof; the EPB Hall is 74 feet high over a much larger area and is much bulkier.

The Bevatron is built back into the hill so that portions of it are below grade. The EPB Hall is in front of the Bevatron, blocking any glimpse of the Bevatron that might otherwise exist. The EPB hall is one of five LBL buildings on the hill that can be widely seen from below, also including the Cyclotron, Building 50, Building 88, and Building 90. Phase 5. Earthquake Rehabilitation Plan Work began under a contract let in January on a plan to strengthen the Bevatron against earthquakes. This plan was developed by John J. Earle, structural engineer with the LBL Plant Engineering Department (predecessor of the Berkeley Lab Facilities Department).

Some of the principal Bevatron project construction contracts were let to the following companies: Installation of Magnet Assembly: Gilmore Steel Wiring Raceway: Garlervy; California Steel Company Electrical Power Installation: Severin & Brayer Electrical Flywheel and Motor/Generators: G. W. Thomas Drayage and Rigging Concrete Radiation Shield Foundation: 0. C. Jones BUBBLE CHAMBER BUILDING (BUILDING 59, DEMOLISHED Building 59 was a freestanding structure built northwest of the Bevatron but connected to it by a heavy concrete pad. It was designed and built at the same time as the Building 51 Addition, shown in as-built plans dated February 11, prepared by Milton T. Pflueger, Architect.

A contract was let for construction of these buildings in February The Bubble Chamber Building was in two principal parts. It was a pair of parallel rectangles of unequal size and height, a low office and shop wing x 29 feet) on the north, and a 40 foot high crane bay x 40 feet) in the south. The low wing included rooms for mechanical equipment, a shop, and a control room, and the high wing housed the bubble chamber. Both wings had solid concrete-panel lower walls and bands of corrugated translucent plastic above. Construction photographs show steelwork for the EPB hall built around Building 59 and the demolition of Building 59 only when the EPB hall was nearly finished, in Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 43

Ancillary Buildings

Accelerator Design Building (Building 64) The Accelerator Design Building was designed and built in stages. The first stage is shown in a set of as-built drawings prepared by lndenco Engineers of Oakland, dated January 3, and was built under a contract let in January The original building consisted of two, two-story rectangular volumes in series, with a higher and wider section close to the north end of Building 51, and a lower and narrower section to the north of the first section. The larger section enclosed a single, partitionable space broken by two interior rows of columns on the ground floor, and a column-free loft upstairs under a trussed roof. The smaller volume housed offices.

The second phase, at the west end of the original building, and at an angle to it, is shown in as-built drawings prepared by Corlett and Spackman, dated June 27, and was built under a contract let in June This addition housed offices and a loft area for mechanical engineering on the ground floor, and offices and a loft area for plant engineering upstairs. In the Accelerator Design Building underwent major modifications, including installation of a 30-ton crane and a cooling tower on the hill behind the building. The interior was reorganized so that, on the ground floor, bubble chambers occupied the north end of the building, electronics engineers and installers occupied the middle, and testing equipment occupied the south end in a two-story space created by the removal of the second floor.

Upstairs, mechanical engineering occupied the middle between offices to the north end and the upper part of the crane bay to the south. In the original central entrance to the building was converted to an experimental area. In new foundations were designed for the 50-MeV HILAC. After formation of the Bevalac in Building 64 housed the Bevalac Engineering Group. Later it housed the Accelerator and Medical Physics Groups. HILAC Building (Building 71) The existing building was linked to the Bevatron by way of the Beam Transfer Line when the Bevalac was established. A detailed description of the HILAC Building is not part of this HAER documentation.

Buildings Associated with Bevalac Operation

The establishment of the Bevalac involved modifying and linking the machinery in two existing buildings, the Bevatron and the HILAC, but has not involved major modifications of the buildings themselves, except to accommodate additional experimental equipment. Those which were considered buildings and are recorded in the building records are described below. HISS Users Buildings Two prefabricated buildings, so-called Butler Buildings, described on drawings dated February 23, as Relocatable Experimental Shelters, were designed by Construction, Inc., of Oakland, to be built at the north end of the EPB hall. Both were small, windowless rectangular structures with light steel frames, and vertical metal Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 44 exterior cladding. Building No.

1, with three rooms, was 24 x 60 feet; Building No. 2, with a single interior space, was 30 x 50 feet. Experimental Computer Enclosure (Building 51 L) The Experimental Computer Enclosure is a one-story rectangular structure south of the EPB hall near its junction with the Bevatron. The building measures 24 x 36 feet. It contains a wide central room flanked by narrow rooms, each with a small separate room at the rear. It is a light steel-frame structure with vertical siding and a very slightly pitched roof. It was built according to a set of architectural drawings dated July 19, Bevalac Patient Facility (Building 51 N) The Bevalac Patient Facility is a small building located inside the Bevatron Experimental Area, on the north side of the magnet room.

This is a light steel-frame structure with "prefinished" metal siding and foil-faced fiberglass batt insulation. It is rectangular in plan (32 x 20 feet). Stud wall partitions divide the interior along a central corridor, with a tech-station, viewing room, and toilets on one side, and a waiting room, dark room, and exam room on the other. It was designed according to a site plan and other drawings from April, Architecture of the Bevatron Building Complex

Accelerator Building

The first modern subatomic particle accelerators were built in existing lab space at the University of California at Berkeley in the late and early The first cyclotron, with a diameter of five inches, was used by E.O. Lawrence in a lab in Le Conte Hall on the main campus of the University of California at Berkeley in Beginning in a series of increasingly larger cyclotrons were built in a room in a building originally designated the Civil Engineering Test Laboratory (later renamed the Old Radiation Laboratory) on Hearst Street adjacent to the main campus.

Lawrence described this as "a large frame structure with several substantial concrete piers in the rooms" (Lawrence cited in Heilbron, A photograph of one of the cyclotrons in this building showed walls of ordinary wood construction in the background. A photograph published in of a 1.3 BeV electron synchrotron at Cornell University shows that as late as the unmodified lab space was used for particle accelerators (Wilson and Littauer, 1960:Plate XI). As accelerators grew larger and their needs for power increased, new accelerators began to be built. The first of these was the Cyclotron Building for the University of California Radiation Lab (currently designated Building 6) on the hill east of the main campus.

Construction of this building (Building 6) began in the Cyclotron went into operation in The Cyclotron Building was designed by Arthur Brown official campus architect, and one of the most distinguished architects of his day in California. He also designed, alone or with partners, the city halls in San Francisco, Berkeley, and Pasadena; the Opera House and Coit Tower in San Francisco; and Hoover Tower at Stanford University. The Cyclotron Building was carefully sited and designed to express the pre-eminence of science in the modern university and the modern world. Its siting Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 45 was on axis with the main campus plan below, and its carefully proportioned dome was in harmony with the Beaux-Arts buildings of the campus.

Except for its siting and dome, the design of the Cyclotron Building was the product of standard modern practice for the design of industrial buildings. A later article on the design of accelerator buildings expressed the process concisely as follows: "Architectural form usually emerges from a site, a list of project requirements and a budget provided by the client to his architect" (Leposky, In other words, the building is largely the result of practical needs and constraints. Like other industrial structures, its form is the product of the activities and the machines inside. After World War II, planning began-with the involvement of the AEC-for new accelerator facilities at Brookhaven (New York), and Berkeley.

These would be proton synchrotrons called the Cosmotron at Brookhaven and the Bevatron at Berkeley. They were approved at the same time, although the Cosmotron went into operation in two years before the Bevatron. The approach taken to the design of buildings for two machines of the same type at the same time in the same country begins to illustrate the variety of appearances that were possible, and that characterize the increasing number of accelerator buildings around the world in the years that followed. One might say that for one type of building-the accelerator building-various styles were possible. Accelerator buildings could be symmetrical or not, they could appear grand or factory- like, they could be ornamented in a modern way or with historical references.

Designers of the Bevatron followed up to a point the example of the Cyclotron, which had a 24- sided, circular main building clad in transite panels and horizontal bands of windows; at the same time, the Bevatron was less symmetrical and it lacked historical ornamental references. Although the Cyclotron and Bevatron buildings reflected the shape of their respective accelerator machines, the Cosmotron Building did not. Similar machines and activities were sheltered by a symmetrical, generally rectangular building whose appearance reflected linear craneways inside, rather than the shape of the accelerator apparatus. Beginning in the many new accelerators would be built in the United States, the Soviet Union, Western Europe, and Japan.

Designers of buildings for these machines were faced with a consistent set of problems, to provide shelter and services for accelerator machines and power sources, experiments, control systems, and radiation shielding, and to provide circulation space, room to expand, cranes, and light. To this common set of problems, the designers brought a consistent approach to design, common in designing for industry, in which the form was generated by the specific needs of the situation. The great variety in specific circumstances, including the type of accelerator (linear, proton synchrotron), the size of the machine and power needs, the site, the presence or lack of existing lab and office facilities, produced a great variety of buildings.

Discussed in traditional terms of structure, plan and function, and image, a few generalizations can be made about accelerator buildings. Structurally, all accelerator buildings appear to be steel-frame or reinforced concrete with heavy concrete foundations. Some accelerators are built partly underground for shielding purposes. Accelerator buildings are varied in plan, with respect to the accommodation of variable Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 46 research programs.

Plan types include those represented by the mile-long linear accelerator at Stanford (Stanford Linear Accelerator Center), the makeshift accretion of parts of the Bevalac, and the highly ordered, master-planned research campuses of Fermilab near Chicago, and CERN (Organisation Europeenne pour la Recherche Nucleaire) near Geneva. As for architectural image, most are straightforward buildings using modern industrial materials which represent in modest ways the pre-eminence of science and reason. Only a few, like the Cyclotron at Berkeley and the Soviet accelerator at Dubna with its exterior characteristic of Soviet civic architecture-are reminiscent of the overscaled Italian fascist architecture of Mussolini (Jungk, 1968:Plate), possessing larger symbolic or architectural pretensions.

In all of these ways, accelerator buildings are an international building type, the product of twentieth-century attitudes toward planning and design held in all advanced industrial countries. Individualistic touches, such as the dome of the Cyclotron and the exterior cladding of the proton synchrotron at Dubna, are rare and superficial (at Dubna, the magnet room interior is similar to, but larger than, the magnet room of the Bevatron). As an international type, each of several countries produced no more than a few in the early years, and each accelerator and accelerator building was an effort of the national government or a cooperative venture of more than one government, together with leading scientists and universities in those countries.

Finally, like other industrial building types, accelerator buildings are designed to accommodate machines. Some industrial buildings simply shelter machines from the elements so that machines of different types for different processes might simply be moved in or out as needed, like furniture. Other industrial buildings are designed for specific machines and processes. Steel mills, glass factories, flour mills, slaughterhouses, and many gravity-process factories are examples of this type. In these cases, the buildings are designed specifically for a machine process and are essential to the process.

In effect, buildings like these are parts of the machinery, reflecting a statement of pre-eminence for the scientific or industrial apparatus and thereby de- emphasizing architectural elements representing individual or social metaphors. In a sense, the absence of architectural metaphor is in itself a statement. Accelerator buildings are like these industrial buildings. Each one is designed for very specific circumstances (Leposky, Each one is shaped by a variety of forces including the machines to be housed, the site, attitudes to design, and the individuals involved; each one is, in effect, part of the machine. The Bevatron Building (Building 51 ), for example, has become more complicated and more machine-like as it has been modified over the years.

The Bevatron machinery could not operate without it. The Bevatron Building is integrated with the operation of the Bevatron machinery in the following ways: the two cranes in the circular magnet room, and the other cranes in the main experimental area as well as the External Proton Beam Hall (Building 51 B), have been essential to the construction, maintenance, and repair of the magnet and other machines; the foundations provide support for very heavy and highly-specialized equipment such as the magnet, the injector, the HISS, and the shielding; the power room is an essential component for running the Bevatron; and the ducts under the floors carry air from the fan room to cool the machine.

In this way, the Bevatron Building is like other accelerator buildings, inseparable from the accelerator for which it was built. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 47 Architecture of the Bevatron/Bevalac Building Complex The Bevatron/Bevalac at Berkeley Lab is a complex of buildings and machines located on a steep site on a hill east of the University of California at Berkeley main campus. Because of the steep topography, it is set among other buildings of the Laboratory that are situated on a limited number of buildable sites; at the same time, the buildings are grouped as much as possible by function. For most of its history, building at the Lab proceeded without the guidance of a master plan. Buildings 51/51A form the Bevatron Building core complex.

Building 71 (SuperHILAC Building), Buildings 51 B (External Proton Beam Hall) and 64 (Accelerator Design Building), and the Beam Transfer Line, are given brief descriptions below in the interest of establishing the architectural and physical context of the Bevatron Building (Building 51/51A). The Bevatron/Bevalac consists of two major building groups which were originally built for unrelated purposes and which were built on sites separated by 124 feet in elevation. These are linked by a transfer line, which contains an evacuated aluminum pipe within which accelerated particles traveled from the SuperHILAC (Building 71) above, to Building 64 and the Bevatron (Building 51 and 51A for the purposes of this report) below.

Building 71 and Buildings 51 and 64 were built without any design relationship to each other. Building 71 is oriented east-west; Building 51 is oriented in a scattered way northwest-southeast; Building 64, oriented north-south, is in a narrow space between the hill and the EPB Hall (Building 51 B) at the Bevatron. Buildings 51 and 71 have multiple additions which obscure the clarity of their images, orientations, and relationships to other buildings. As a result of the difference in elevation and orientation of the buildings, the route of the transfer line is indirect. The pipe of the transfer line is carried partly below ground and partly above ground on wooden frames.

In short, the complex developed over a period of time from independent actions rather than in a single rational planning effort such as occurred at some other accelerators (e.g., CERN in Switzerland). The overall appearance of the Bevalac buildings is disorderly. It has the character of a makeshift lab experiment blown up to the proportion of buildings. Because of the topography, it is difficult to grasp the complex as a whole from the site or from a distance. From a distance, portions of the Bevalac are visible (the EPB hall of the Bevatron is widely visible because of its height, Building 71 can be glimpsed from some vantage points), but nowhere is it possible to see it whole.

For anyone unfamiliar with the Bevalac, even when the different parts are seen, there is no obvious reason to understand these parts as a whole. The elements of the Bevatron/Bevalac are described below in functional order: the Bevatron Building (Building 51/51A), and then the ancillary buildings (Buildings 71, 51 B, 64, and the Beam Transfer Line). The descriptions which follow are intended to present a picture of the buildings as they are today, in contrast to the earlier section where the history of construction was presented (Fig. Bevatron Building (Building 51/51A) The Bevatron Building (Buildings 51 and 51A) today is a complex, irregularly shaped structure with five principal parts, the design being a consequence of several successive Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 48 building campaigns: the circular magnet room, the curving shop-and-office wing on the periphery of the magnet room (Figs. the curving experimental area also on the periphery of the magnet room (51A), the rectangular mechanical wing, and the larger rectangular EPB hall (Figs. 66, Inside and around the Bevatron Building are small structures associated with experiments. The magnet room is at the center of a larger circular area including the shop-and- office wing and the experimental area. Stretching away from this circle are the rectangular mechanical wing in a north-by-northwest direction, and the EPB hall in a northwest direction. The transfer line from the HILAC Building enters the Bevatron between these two wings.

The Bevatron is entirely a steel-frame structure above a much-rebuilt foundation of reinforced concrete (Figs. The foundation has been strengthened in places to support the magnet, the injector, the motor/generators and other electrical equipment, and various experimental machinery including the HISS. In addition, the foundation incorporates tunnels for access to the magnet, the accelerator tanks, and the various ducts-for cooling air coming from the fan room and the outside cooling towers to the magnet, for the vacuum pumping system, and for a variety of control-line conduits. Above this complex foundation, the steel frame is generally exposed inside. Outside, the building is clad in corrugated transite, with clerestory bands of metal sash windows and louvered ventilators.

Visually and functionally, the magnet room is the heart of the Bevatron building. This is a near-circular space (actually a 24-sided polyhedron) spanned by two tiers of trusses with a central column (Fig. 71 ). The lower tier of trusses is called the roof truss. The upper tier, called the monitor truss, lifts the center of the roof in order to provide space for a ring of ventilators. From the outside, this roof is a shallow cone in two sections. Two 30-ton cranes span the distance from a crane rail around the central column to the periphery of the magnet room. Beneath the cranes is the shielding structure of massive concrete blocks which completely encloses the magnet. Tangent to the magnet room and extending north by northwest is the mechanical wing.

At the north end of this wing is the high, open motor generator room (Fig. 72) where the power is produced to run the Bevatron. At the south end is the fan room for cooling the magnet. In between, the space of the magnet room is extended into this wing in order to house the injector. The space of the magnet room extends into a space designated on the plans as the experimental area for 10 bays (Building 51A) around the northwest periphery of the magnet room. This space is served by a 30-ton crane which runs along a curving path for its full length. Projecting beyond the experimental area is another experimental area, the large, high, open space of the EPB hall (Building 51 B) with its large craneway. The EPB hall is open at its base and clad in large vertical metal and plastic panels above.

On the south side of the magnet room is the curving two-story shop-and-office wing, including the control room (Fig. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 49 Future Plans Currently there are plans to use some of the office and laboratory space in Building 51 to meet space and facility needs to achieve Berkeley Lab's science and technology mission. The potential exists for use of this space for accelerators or other large experimental apparatus. For example, the laboratory is evaluating locations for experimental equipment for its heavy-ion fusion program. However, Berkeley Lab reserves the right to demolish the building in order to meet program and facilities needs, if necessary. Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 50 References and Bibliograph Adams, John. The evolution of big science. In: Proceedings of the Celebration of the Anniversary of the Lawrence Berkeley Laboratory. United States Department of Energy. Advisory Council on Historic Preservation. Balancing Historic Preservation Needs with the Operation of Highly Technical or Scientific Facilities. Washington, - - . Proposed Council Guidelines: Consideration of Highly Technical and Scientific Facilities in the Section 106 Process. Advisory Council on Historic Preservation and GSA lnteragency Training Center. Introduction to Federal Projects and Historic Preservation Law. Participants Course Book. Arlington, Virginia. Alonso, Jose. Current status and planned improvements of the Bevalac. In: S.

Elam, ed., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac Pp. Alonso, J. Howard, T. Criswell, W. Chu, F. Lothrop, and C. Weber. The Bevalac biomedical facility. In: Pirrucello and C.A. Tobias, eds., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Pp. Alpen, Edward and F. Lothrop. National biomedical heavy-ion research program at the Bevalac. In: S. Elam, ed., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac Pp. Alvarez, Luis. The hydrogen bubble chamber and the strange resonances. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Barklow, Timothy and Martin Perl. Elementary particle physics.

Encyclopedia of Physical Science and Technology Bernstein, Jeremy. The Tenth Dimension. McGraw-Hill Publishing Company, New York. Blewett, Hildred. Characteristics of typical accelerators. Annual Review of Nuclear Science 68. Blewett, John P. Recent developments in proton synchrotrons. Annual Review of Nuclear Science - - . Accelerator design and construction in the In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Bodvarsson, Mary. Bevatron goes down in history. Currents 1. Bradner, Hugh. Bubble chambers. Annual Review of Nuclear Science Brobeck, William. Personal communication. October 5, Brown, Max Dresden, Lillian Hoddeson, and May West, eds. Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge.

Butowsky, Harry. Personal communication. December 15, California Alumni Association. Students at Berkeley. California Alumni Association, Berkeley. California Monthly. Chimes from the Campanile. California Monthly (August-September) p. 22. Castro, Joseph R. et al. Heavy-ion therapy. In: S. Elam, ed., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Pp. Chamberlain, Owen. The discovery of the antiproton. In: Brown et al., eds., Pions to Quarks: Particle Physics i1 the Cambridge University Press, Cambridge. Pp. Chew, Geoffrey F. and Burton J. Moyer. High-energy accelerators at the University of California Radiation Laboratory. American Journal of Physics Childs, Herbert. An American Genius: The Life of Ernest Orlando Lawrence. E.P. Dutton and Company, New York.

Chinowsky, William. Strange particles. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Chu, E.L. and L.I. Schiff. Recent progress in accelerators. Annual Review of Nuclear Science 92. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 51 Cole, and M. Tigner. Particle accelerators. Encyclopedia of Physical Science and Technology Consodine, Douglas M., ed. Particles. Van Nostrand's Scientific Encyclopedia, Seventh Edition Courant, Ernest D. Early history of the Cosmotron and AGS at Brookhaven. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Dalitz, Richard H. K-meson decays and parity violation.

In: Brown et al., eds., Pions to Quarks: Particle Physics h the Cambridge University Press. Pp. Day, Lucille. Pulsed magnet will cut energy use at Bevalac. Currents Fretter, William B. Nuclear particle detection (cloud chambers and bubble chambers). Annual Review of Nuclear Science Galison, Peter. Bubbles, sparks and the postwar laboratory. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Gebhard, David. Lawrence Berkeley Laboratory, The Cyclotron Building. The Historical Significance of the Building: Recommendations in Regard to Proposed Alterations. Ira Fink and Associates, Inc., University Planning Associates, Berkeley. Unpublished. Gell-Mann, Murray.

Progress in elementary particle theory, In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Ghiorso, Albert. On the Origin of the Bevalac. Unpublished paper presented at Lawrence Berkeley Laboratory conference: The Bevatron!Bevalac: Its People and Science, October 25, Goldhaber, Gerson. Early Work at the Bevatron: A Personal Account. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. - - . Early emulsion work, K-mesons and antiprotons. Unpublished paper presented at Lawrence Berkeley Laboratory conference: The Bevatron!Bevalac: Its People and Science, October 25, Goldhaber, Judith. LBL to commemorate Bevatron's anniversary. Currents 11 (41 - - .

Proposal calls for replacing Bevatron with new machine. Currents - - . Bevalac detector finds first electron pairs. Currents 1. Gough, Richard. Personal communication. October 1, Grunder, Hermann A. Proton synchrotron. McGraw-Hill Encyclopedia of Science and Technology, Seventh Edition Grunder, Hermann A. and Frank B. Selph. Heavy-ion accelerators. Annual Review of Nuclear Science Heilbron, An historian's interest in particle physics. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Heilbron and Robert W. Seidel. Lawrence and his Laboratory: A History of the Lawrence Berkeley Laboratory, Volume 1. University of California Press, Berkeley. Heilbron, Robert W. Seidel and Bruce R. Wheaton.

Lawrence and his Laboratory: Nuclear Science at Berkeley. Lawrence Berkeley Laboratory and Office for History of Science and Technology, University of California, Berkeley. Hubbard, Edward L. Heavy-ion accelerators. Annual Review of Nuclear Science 11 Jones, Lawrence W., Luis W. Alvarez, Ugo Arnaldi, Robert Hofstadter, Donald W. Kerst, and Robert R. Wilson. Panel on accelerators and detectors in the In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Judd, David L. Conceptual advances in accelerators. Annual Review of Nuclear Science Jungk, Robert. The Big Machine. Charles Scribners and Sons, New York. Kahn, Jeffrey. Bevalac computing system boosts processing power. Currents Univ.

of CA Radiation Lab, Bevatron HAER CA-186-A Page 52 Kollath, Rudolf, ed. Particle Accelerators. Sir Isaac Pitman and Sons, London. Kapa, Adrienne. More precise delivery of radiotherapy beams made possible with new technique. Currents :1. - - . Bevalac draws users from around the world. Currents LaMacchia, Diane. Bevatron. Unpublished video script. Lawrence Berkeley Laboratory Office of Public Information. Lambertson, Glen R. The Bevatron. Unpublished paper presented at Lawrence Berkeley Laboratory conference: The Bevatron/Bevalac: Its People and Science, October 25, Lawrence, E.O. The evolution of the Cyclotron. In: M. Stanley Livingston, ed., The Development of High-Energy Accelerators. Dover Publications, New York. Pp. [Reprint of Nobel Prize acceptance lecture.] Lawson, and M. Tigner.

The physics of particle accelerators. Annual Review of Nuclear Particle Science Leposky, George. What's the best way to build a million atom smasher? Inland Architect Livingston, M. Stanley. High-energy accelerators: proton synchrotron. Annual Review of Nuclear Science - - . Particle Accelerators: A Brief History. Harvard University Press, Cambridge. Livingston, M. Stanley, ed. The Development of High-Energy Accelerators. Dover Publications, New York. Livingston, M. Stanley and John P. Blewett. Particle Accelerators. McGraw-Hill, New York. Lofgren, Edward J. The Bevatron. The Proceedings of the National Academy of Sciences - - . Synchrotrons and bevatrons. In: Charles Susskind, ed., The Encyclopedia of Electronics, Reinhold Publishing. Pp. - - .

Personal communication, September 20, McCulloch, Thomas. Personal communication. December 9, McMillan, E.M. The Synchrotron: a proposed high-energy particle accelerator. In: M. Stanley Livingston, ed., The Development of High-Energy Accelerators, Dover Publications, New York. Pp. [Reprint from: McMillan, E.M. The Synchrotron: a proposed high-energy particle accelerator. The Physical Review Piccioni, Oreste. On the antiproton discovery. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Riordan, Michael. The Hunting of the Quark. Simon and Schuster, New York. Ritson, David M., ed. Techniques of High Energy Physics. lnterscience Publishers, New York. Scharf, Waldemar H. Particle Accelerators-Applications in Technology and Research.

John Wiley, New York. Schweber, Silvan S. Some reflections on the history of particle physics in the In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Seidel, Robert W. Accelerating science: the postwar transformation of the Lawrence Radiation Laboratory. Historical Studies i1 the Physical Sciences - - . The post-war political economy of high-energy physics. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Slater, High energy accelerators: linear accelerators. Annual Review of Nuclear Science Stevenson, M. 1993a. The Berkeley programme. In: Conference on the Bubble Chamber and Its Contributions to Particle Physics, CERN. - - . Physics with bubble chambers.

Unpublished paper presented at Lawrence Berkeley Laboratory conference: The Bevatron/Bevalac: Its People and Science, October 25, Syversrud, Harvey. Personal communication. July 22, Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 53 Telegdi, Valentine L. The early experiments leading to the V-A interaction. In: Brown et al., eds., Pions to Quarks: Particle Physics in the Cambridge University Press, Cambridge. Pp. Thomas, J.E. , William L. Kraushaar, and I. Halpern. High-energy accelerators: synchrotrons. Annual Review of Nuclear Science Tobias, Cornelius A., Eleanor A. Blakeley and Ruth J. Roots. Cellular and molecular radiobiology. In: S. Elam, ed., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Division of Biological and Environmental Research, U.S.

Energy Research and Development Administration. Pp. - - . International cooperation in heavy-ion research. In: Pirrucello and C.A. Tobias, eds., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Office of Health and Environmental Research of the U.S. Department of Energy. Pp. United States Code. National Historic Preservation Act of as amended (16 U.S.C., United States Atomic Energy Commission. Radiation Laboratory, University of California, Berkeley. [Berkeley Lab Archive] United States Department of the Interior. 36 CFR Part 60, National Register of Historic Places. U.S. Government Publishing Office. - - . National Register Bulletin 15. How to Apply the National Register Criteria for Evaluation. U.S. Government Printing Office.

United States General Accounting Office. DOE's Physics Accelerators: Their Costs and Benefits. April 1, U.S. Government Printing Office. University of California Lawrence Berkeley Laboratory First acceleration of heavy ions at the Bevatron. The Magnet - - . 1972a. Cryopumping adds to Bevatron versatility. The Magnet - - . Research Highlights. [Berkeley Lab Archive] - - . Heavy ion facility, the Bevalac, is on the way. The Magnet - - . Bevatron Monthly Report for August [Berkeley Lab Archive] - - . 1977a. Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, S. Elam, ed., Division of Biological and Environmental Research, U.S. Energy Research and Development Administration. - - . The long ride. News Magazine Summer - - . Hot stuff. News Magazine Spring - - .

Enter HISS. News Magazine Spring - - . 1980a. LBL Overview. [Berkeley Lab Archive] - - . Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Pirrucello and C.A. Tobias, eds., Office of Health and Environmental Research of the U.S. Department of Energy. - - . The right kind of beam. News Magazine Fall - - . 1981a. Up to uranium. News Magazine Spring/Summer :4. - - . Accelerator and Fusion Research. [Berkeley Lab Archive] - - . Images in a plastic ball. News Magazine Winter - - . Physics in thin air. News Magazine Spring/Summer - - . Beam bonanza; beam for the future. Research Review - - . Bevalac detector. Currents - - . 1991a. Annual report. [Berkeley Lab Archive] - - . b. Cosmic ray questions. LBL Research Review :2. - - . 1992a. Creating quark matter.

LBL Research Review Summer - - . Bevalac slated to close. Currents University of California Lawrence Radiation Laboratory The Bevatron. Radiation Laboratory Bulletin Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 54 - - . 1958a. Cascade particles and antiprotons observed in propane bubble chamber. The Magnet - - . Status, Fiscal Year [Berkeley Lab Archive] - - . 1959a. Bubble chamber operating. The Magnet - - . Anti lambda seen in bubble chamber. The Magnet 1. - - . Segre and Chamberlain win Nobel Prize. The Magnet3(11):1. - - . Status, Fiscal year [Berkeley Lab Archive] - - . 1960a. Berkeley scientists investigate nuclear forces by studying pion interaction. The Magnet - - . Bevatron to be made more modern; big modification program is planned. The Magnet 1. - - .

Status Fiscal Year. [Berkeley Lab Archive] - - . Particle hunters bag a big one-the omega. The Magnet - - . Status, Fiscal Year [Berkeley Lab Archive] - - . 1963a. data points to major theoretical gains. The Magnet7(1):1. - - . Bevatron due back on job this month. The Magnet - - . 'Rebirth' of Bevatron acclaimed by scientists. The Magnet7(3):3. - - . 'Disciplined' protons are put to work in unique LRL developed target. The Magnet - - . Fiscal Year Report [Berkeley Lab Archive] - - . 1963e. New 25-inch bubble chamber completed. The Magnet - - . Information Sheet on Bevatron. [Berkeley Lab Archive] - - . The Bevatron. [Berkeley Lab Archive] - - . Status, Fiscal Year [Berkeley Lab Archive] - - . 1966a. 'Hail and farewell' to 72-inch bubble chamber. The Magnet [No issue number] - - .

Annual Report. [Berkeley Lab Archive] - - . 1967a. Bevatron is shut down for generator repair. The Magnet 11 (1 - - . Annual report. [Berkeley Lab Archive] - - . 1968a. Eta Zero-Zero. The Magnet. [No volume, Page 3] - - . Spark chambers blaze new trails in particle physics. The Magnet - - . The Magnet - - . Luis Alvarez wins Nobel Prize. The Magnet - - . 1968e. Annual Report. [Berkeley Lab Archive] - - . 1969a. The Bevatron. LRL Publication 2a/15M. - - . Computer now controls Bevatron's beam. The Magnet - - . Annual Year report. [Berkeley Lab Archive] Veksler, V. A new method of acceleration of relativistic particles. In: M. Stanley Livingston, ed., The Development of High-Energy Accelerators. Dover Publications, New York. Pp. [Reprint from: Journal of Physics [USSR] 9, Wenzel, William.

Bevatron. Unpublished paper presented at Lawrence Berkeley Laboratory conference: The Bevatron!Bevalac Its People and Science, October 25, Westfall, Catherine. The First 'Truly National Laboratory': The Birth of Fermilab, Vols. I and II. Unpublished thesis, Michigan State University. Wilson, Robert R. and Raphael Littauer. Accelerators: Machines of Nuclear Physics. Anchor Books, Doubleday and Company, Garden City, New York. Yang, Chen Ning. Particle physics in the early In: Brown et al., eds., Pions to Quarks: Particle Physics i1 the Cambridge University Press, Cambridge. Pp. Univ. of CA Radiation Lab, Bevatron HAER CA-186-A Page 55 Yang, Tracy, and Cornelius T. Gaffey. Space radiobiology. In: S.

Elam, ed., Biological and Medical Research with Accelerated Heavy Ions at the Bevalac, Division of Biological and Environmental Research, U.S. Energy Research and Development Administration. Pp. Yarris, Bevalac's radioactive beams allow new area of study. Currents - - . Kaan studies yield clues to changes in nuclear fireball. Currents 1. Zinenko, A.S. et al., Zdani/ia Uskorite/ei. Nanka, Moscow. ADDENDUM TO HAER No. CA-186-A UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON (Ernest Orlando Lawrence Berkeley National Laboratory, 51/51A) 1 Cyclotron Road Berkeley Alameda County California

Photographs Written Historical and Descriptive Data

Historic American Engineering Record National Park Service Department of the Interior Oakland, California HISTORIC AMERICAN ENGINEERING RECORD ) Addendum to University of California Radiation Laboratory Bevatron (Ernest Orlando Lawrence Berkeley National Laboratory, 51/SlA) HAER No. CA-186-A Addendum to 55 data pages previously transmitted to the.Library of Congress. The Bevatron was the most powerful accelerator in the world when it was built and was a leading research facility among particle accelerators during its period of significance. It is associated with significant contributions in the fields of particle and nuclear physics. In the late and four Nobel Prizes were awarded for particle physics research conducted in whole or in part at the Bevatron.

UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 57) This report is an addendum to HAER No. CA-186-A. It focuses on the architectural information for the Bevatron lA) as the original report contained extensive discussion of the building's historic context, significance, and construction. PART II. ARCHITECTURAL INFORMATION A. General Statement: 1. Architectural character: Building lA is a modem industrial building characteristic of its period in that its form directly reflects its function. It is typical of accelerator buildings in its materials; its plan, however, directly reflects the shape and mechanical support needs of the Bevatron it houses. 2. Condition of fabric: The current condition of the Bevatron 51/51A) is fair.

The removal of the External Proton Beam hall left much of Building 51A open to the elements and the removal of the generators from the generator room and part of the supplemental shielding block from the Bevatron itself have left the overall equipment in a state of disrepair. B. Description of Exterior: 1. Overall dimensions: The building consists of a circular (actually a 24- sided polyhedron) magnet room in diameter with a 34' -wide two- story shop-and-office wing in a quarter circle along the south side and a x 71. 5' rectangular two-story mechanical wing tangent to the circle on the northeast. 2. Foundations: Reinforced concrete foundation. The original foundation was designed by Huber & Knapik, Engineers.

It was a 1O'to13' ring of concrete caissons with an inner radius of 60'to Additional foundation support was poured to support additional concrete shielding during the Major Improvement Program of 3. Walls: The exterior cladding is corrugated asbestos-cement transite panels. 4. Structural system, framing: This is a steel-framed building (Fig. 1). 5. Porches, stoops: There are no porches or stoops. 6. Chimneys: There are no chimneys. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 58) 7. Openings: a.

Doorways and doors: The office-and-shops section has three exterior doorways: one single door on the east end of the section; the main entrance at the intersection with Building 5 lA on the south side, which is a double door with a 3-light window on each side and a pair of 6-light sashes above a wood awning; and a double doors in the center of the section. The mechanical wing has a single pedestrian door on the north end of each of the first- and second-story. The west side of Building 51A has a series of metal roll-up doors as well as pedestrian doors at either end. There is also a pedestrian door into the south comer of Building 51A from the second floor level (ground level on that side), which connects to a set of stairs down to the main floor. b.

Windows and shutters: Steel sash multi-light windows are used throughout. Clerestory bands of fixed sash windows circle the magnet room and the exterior wall of Building 51A. Bands of fixed sash windows extend along the second story of the east side of the mechanical wing. The second floor of the office-and-shops sections has paired sets of paired sets of nine-over-nine-light sash windows across the fa9ade. C. Description of Interior: 1. Current floor plans are attached as Figures 2, 3, and 4. Building lA forms a shelter and provides infrastructure support for the Bevatron, a weak-focusing proton synchrotron 1 centered in the building's large central high bay, known as the accelerator gallery or, more commonly, magnet room. a.

Building 51 consists of a large, circular, central area known as the magnet room; a two-story office-and-shop wing curving along the south periphery of the magnet room; and a rectangular mechanical wing extending north-by-northwest tangentially to the east side of the magnet room. b. Building 51A is the result of two additions and It curves along the northwest periphery of the magnet room from the mechanical wing south to the office-and-shops area. It was 1 A synchrotron is a particle accelerator that fixes the orbit radius by synchronizing the magnetic field and the accelerating radiofrequency with the particle velocity. UNNERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 59) originally designed to house equipment and experimental set-ups in ten bays. c.

In the years since the Historic American Engineering Record documentation of the Bevatron was completed, most of the non-eligible elements (including Building 5 lB-the External Proton Beam (EPB) hall-and the beamline that extended into it) of the Bevatron area have been removed. There also has been some renovation to the office-and-shops areas, converting the shops and control areas into additional office and computer support space, primarily for programs unrelated to accelerator science. The original Building 51 and the 51A addition remain, as does the body of the Bevatron and much of its supporting infrastructure. However, all of its exterior experimental equipment and controls are gone, as are the generators and related equipment from the mechanical wing. d.

The center support for the ceiling and roof of Building 51 is a steel center support column that bears on the center of the magnet room foundation (Fig. 5 and 6). The column extends through the center of the Bevatron, holding a variety of equipment (Fig. 7), and then proceeds through the center of the Bevatron shielding (CA-186-A-74). The column then serves as a support for the roof trusses and the internal attachment point around which the magnet room's two 30-ton radial cranes tum before it reaches the center of the roof structure (CA-186-A-75). e. The central round roof of Building 51 is supported by a series of radial roof trusses that span from the central support column to structural columns at the perimeter.

These trusses incorporate a raised monitor that creates a ring of windows, allowing natural light into the center of the building (Fig. 8). The truss beams are assembled with rivets (CA-186-A-76). f. The roof of Building 51A is supported by a Pratt truss. 2. Stairways: There are multiple stairways in and around the building, of metal, concrete, and wood; they provide access between the main floor of the building and the second-floor office section and mechanical area, as well as from the basement-levels. Access is also provided from the main magnet room floor to the basement tunnel that leads to the center of the Bevatron, as well as from the main level to a deep tunnel that extends under the Bevatron in the foundation.

A stairway is also installed between the basement (lower) floor and beamline level tangent sections within the center of the Bevatron. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 60) a. Exterior access to the second floor of the mechanical section is provided by a quarter-tum concrete stairway with metal handrails that reaches from the ground level to the concrete pad outside of the mechanical section (Fig. 9). A concrete flight of stairs then extends to mechanical section (Fig. b. A concrete flight of stairs also leads from the concrete pad to the main level of the mechanical section (Fig. 11 ). c.

In the interior of the mechanical section, a metal stairway with metal handrails provides access from the second floor electrical mezzanine to the catwalk above the switchgear area (CA-186-A- d. Two metal stairways with metal handrails access the second floor of the machine area, one from the main floor generator room up to the switchgear area and one from the main floor of the magnet room, near the local injector control room (Room up to the mezzanine outside of the fan room (Fig. 12 and e. A flight of metal stairs with metal handrails connects the basement (generator pit area) under the generator room to the main floor of the generator room (Fig. f. A quarter-tum metal stairway with metal handrails and landings extends from the fan room mezzanine to the filter banks (Fig. g.

In the a stairway for emergency egress was added between the magnet room floor and the catwalk, near Room 9B. This stairway has three flights of steel half-tum stairs with metal handrails and steel halfspace landings (Fig. h. Two metal stairways with metal handrails provide access from the second-floor office section to the main floor of the building. One stands in the corner joining the Building 51A addition to the office-and-shops section of Building 51 and provides access from the building's exterior (CA-186-A-78). The other, more frequently used, is a half-tum metal stairway extending from the center of the office-and-shops second floor to the main level (CA-186-A-79). UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 61) i.

A metal stairway with a mid-level landing and metal handrail allows access to the top of the Bevatron from the main floor near the west straight section (CA-186-A-80). J. Two sets of wood stairs with shared wood landings and wood handrails lead from the top of the outer edge of the Bevatron shielding to the top of the roof block shielding (CA-186-A-81). k. Ladder access is provided from the top center area of the Bevatron shielding into the center of the Bevatron (Fig. 1. The tunnel extending under the main floor into the center of the Bevatron is accessed by a concrete stairway (CA-186-A-82). m. A wood double-return stair provides access to the beam level from the foundation level within the Bevatron (Fig. 18 and n.

Small wood or metal equipment-access stairs of 3-8 steps are attached to equipment at various points throughout the building (CA-186-A-83 and CA-186-A-84). o. The utility tunnels are accessed from the main level, where Building 51A meets to the shops-and-offices section of Building 51. Tunnel access is provided by a metal ladder with metal handrails (Fig. p. The deep tunnel added in the Major Improvement Program and providing access into the Bevatron's foundation is accessed by a steel spiral staircase with metal handrails around a steel newel (Fig. 21 ). This stairway enters a short concrete tunnel that leads to the actual deep tunnel entry. At that point, there is a metal stairway up to the former EPB hall, now a blocked access door (Fig. 22) and down to the deep tunnel (Fig. 3.

Flooring: The main floor is concrete, as are the floors of shops and mechanical areas. The office area floors are covered in vinyl asbestos tile and, more recently, carpet. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 62) 4. Wall and ceiling finish: a. With the exception of the office-and-shop area, the interior walls of the main and second floors of Buildings 51 and 51A are unfinished, leaving the steel framing exposed. b. The walls of the office-and-shop area are corrugated transite, although the offices currently in use as offices have finished walls of drywall and soft-sided panel dividers to separate the space into office cubicles.

The wall between the second-floor office section and magnet room is corrugated transite and includes windows overlooking the Bevatron (CA-186-A-85). c. The walls of the basement (generator pit area) under the generator room are concrete with thick-walled concrete areas providing foundational support for the generators in the room above (CA-186-A-86 and CA-186-A-87). d. The ceilings of the magnet room and mechanical section are dressed redwood lumber. In the magnet room, the ceiling planks are installed in twenty-four sections parallel to the room's twenty-four polyhedral sides (CA-186-A-88). e. The ceiling of the Building 51A addition is metal decking designed to replicate the wood ceiling of the original Building 51 (CA-186-A-89). f.

The offices in current use have drop ceilings of acoustical tile. 5. Openings: a. Doorways and doors 1. Building 51 predominantly has metal doors throughout, although some offices have wood doors. These are single- leaf doors. The building's pedestrian entrances enter the second-floor of the offices-and-shops section and through the mechanical section. There is a double-leaf door at the main entrance to the office-and-shops section and a single- leaf door further to the south. A single-leaf door near the main entrance provides access to a stairwell into Building SIA. Pedestrian doors also enter the north end of the mechanical section. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 63) 2. The north end of the mechanical wing has a large roll-up steel door. 3.

Building 51A has a series ofroll-up doors along the exterior wall. Roll-up doors and wall panels in five exterior wall sections were removed when the EPB hall was built. With the removal of the EPB hall, the wall remains open to the north (CA-186-A-90). Three roll-up doors provide access to the west side. b. Windows: 1. Building 51 has clerestory bands of fixed metal sash windows around both the central magnet room and the mechanical wing. 2. Building 5 lA has bands of fixed steel sash windows above the roll-up doors, matching the original Building 51 design. The windows are in sets of five with two 18-light sash windows on each side of a 24-light sash. There are strips of twelve single-light sashes in the roof of Building 5 lA, near the join with Building 51. 3.

The office-and-shop section has no openings on the exterior of the main floor, as it is built into the hillside, but has paired sets of nine-over-nine-light sash windows. There is a pair of six-light fixed sash windows above the main entrance. On the interior, the second floor of the office-and- shop section also has pairs of metal nine-light sash windows overlooking the magnet room. 4. The mechanical wing has bands of louvered ventilators. A large array of louvers for the main air intake of the Bevatron's cooling system is located on the southeast side. 6. Decorative features: There are no decorative features. 7. Hardware: There is no historic hardware. 8. Mechanical equipment: a. Utilities: The utilities for the Bevatron rest in utility racetracks below the clerestory windows (Fig.

24 and CA-186-A-91). Covered utility trenches that radiate in lines out from the Bevatron are also visible in the flooring. During the building's UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 64) modifications, some of the cabling has been removed and the trenches filled with concrete (Fig. b. Power: 1. Generators: Two flywheel motor generators with sound shrouds were placed on the east and west sides of the north end of the generator room in the mechanical section. The room also held the rectifiers to feed the power to the Bevatron. Both the generators and rectifiers have been removed and the room currently serves as storage space for an program unrelated to accelerator research (CA- 186-A-92). 2.

Switchgear: The switchgear feeding the power through the system is located on the second floor of the mechanical section (CA-186-A-93, CA-186-A-94, CA-186-A-95, and CA-186-A-96). The racks of switchgear were manufactured by Westinghouse. c. Cooling: The Bevatron is air-cooled via a fan system located in the mechanical section of Building 51. 1. Two large centrifugal fans supply cool air through ducts that extend into the passageways under the east side of the Bevatron. The fans sit at the north and south ends of the fan room, on the mezzanine level east of the magnet room. 2. The high speed fans are approximately 15' in diameter and were manufactured by American Blower Corporation of Detroit (CA-186-A-97, CA-186-A-98, CA-186-A-99, and CA-186-A-100).

The pumps and most of the hydraulic fixtures to support the cooling function have been removed from the room, although the motor mounts and the piping remain (CA-186-A-101 and CA-186-A-102). 3. The cooled air was pumped down into the passageways under the Bevatron via large ducts that extended through Room 10 of the main level, directly below the fan room (CA-186-A-103, CA-186-A-104, and Fig. 4. Cooled air entering the passageways under the Bevatron was forced upward through spacings in the magnet laminations; it exited the machine into the magnet room through the shielding block maze entries. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 65) d. Cranes: 1.

Magnet Room: Two 30-ton Moffett radial cranes are installed below the roof trusses of the magnet room to move Bevatron equipment and components, most notably the magnets and shielding block (Fig. 8). The cranes rest on a support track at the outer wall of the magnet room and in a steel-beam ring above the Bevatron (CA-186-A-105). 2. Mechanical Room: A 5-ton crane that originally ran the length of the mechanical room high bay (Room 8) was modified to only serve the first two northernmost bays. A new 15-ton crane was installed in that runs over the basement pit area for the superconducting magnet program. 3.

Building 51A: A 30-ton crane extends across the width of the ceiling of 5 lA, moving along track installed on the interior of the outer wall of 51 A and the exterior of the outer wall of Building 51 (CA-186-A-89). 9. Bevatron: The Bevatron is located in the center of the magnet room and is fully integrated with the infrastructure and foundational support of the building itself. The Bevatron is formed in four 90 curved quadrants of 50' centerline radius, each separated by a 20' field-free gap or straight (tangent) section. The tangents are identified as the north, east, south, and west straight sections. The quadrants consist of magnets, mounted in steel yokes resting on a concrete foundation. The beamline, or particle "racetrack," lies in the center of the magnets in a vacuum chamber.

The straight sections are field-free apertures, across which the beam flows to the next quadrant. Particles were injected into the Bevatron at the east straight section, bent into the circular orbit by an inflector, and accelerated in the north straight section. a. Injectors: 1. Local injector: Although it has had several parts removed and no longer connects to the original Cockcroft-Walton or other source, the local injector is still located outside of the shielding of the northeast quadrant of the Bevatron. It is a linear accelerator providing source particles to the Bevatron-it enters at the east straight section (Fig. 30, CA-186-A-106, and CA-186-A-107). UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 66) 2.

HILAC injection point: In the Bevatron was linked to the SuperHILAC via a beamline that traversed the hillside through the 50 MeV proton injection transport line and entered Building 51 between the mechanical section and Building 51A. The beamline entered the Bevatron shielding near the north straight section and was injected into the Bevatron itself at the east straight section-the same injection point used by the local injector. When operated in this mode, with the HILAC injecting the Bevatron, the facility was known as the Bevalac. The Bevalac operated for the first time on August 1, Most of the transport line from the SuperHILAC has been removed in recent years, leaving a small portion of the hillside transport line. Only a stub of the beamline remains in Building 51 (CA-186-A-108). b.

Control functions: 1. Room 24: Operators ran the Bevatron beam from the control room in Room 22, which held racks of control equipment (Fig. 31 ). Room 22 was remodeled in the late as Building 51 underwent partial conversion for use as office space. The room is now Room 24, and is formed into conventional office space divided by partitions into . cubicles and bearing no trace of its past role in Bevatron operations (CA-186-A-109). 2. Room 11: Room 11 was the control room for the local injector (Fig. It is currently used for storage. Most of the original equipment has been removed and the room does not reflect its original purpose (Fig. c. Shielding: 1.

Exterior Bevatron shielding: Shielding blocks of various sizes surround the Bevatron in two layers, forming the exterior wall of the machine (Fig. The blocks are steel-reinforced poured concrete tapering from a wider outer edge to a narrower inner edge to form an even barrier around the Bevatron's circular shape. Most have a block number and mass printed on the side. Some blocks appear darker gray than the others; the darker color reflects the presence of iron in those blocks, which are consequently heavier and provide more shielding. The darker, heavier blocks are placed along the level of the beamline, where UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 67) more shielding is required (CA-186-A-110).

After the Major Improvement Program extended the beamline into the EPB hall, with associated shielding, the shielding block structure exterior was painted white. When the EPB hall and beamline were removed, the unpainted portion of the Bevatron shielding was revealed (CA-186-A-1l1 ). 2. Entries into shielding block structure: There are three pedestrian access openings through the shielding block, providing access into the magnet areas of each of the northeast, southeast, and southwest quadrants. These openings are designed in a maze configuration to retain shielding protection-the pathways extend between two layers of blocks and then tum into the central area (Fig. 2, 3.

Roof shielding blocks: As part of the Major Improvement Program to increase the beam intensity, additional shielding block was placed around the Bevatron. Shielding blocks were made of poured concrete and placed on top of the magnet ring, becoming a roof to the entire machine (Fig. The roof shielding blocks over each quadrant are placed in two layers-the lower layer of flat blocks have raised edges at the interior and exterior ends, forming a saddle into which the upper layer blocks fit. (Fig. and The upper layer blocks have been removed. The roof blocks over the straight section areas are bordered by taller, single-layer blocks (CA-186-A-112). All blocks are wider at the outside edge and taper in toward the center. d. Magnets: 1.

Foundation: A double ring of concrete walls with gaps for the four straight sections was poured on top of the foundation (Fig. The double ring of walls serves as the magnet foundation (Fig. The magnets rest on these concrete walls, the space below the magnets forms a passageway beneath each quadrant (CA-186-A-113). The air ducts from the fans in the fan room extend into the passageways beneath the quadrants to either side of the east straight section. The north fan feeds air into the passageway under the northeast quadrant of the Bevatron; the south fan ductwork reaches the passageway under the southeast quadrant (CA-186-A-114 and CA-186-A-115). UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 68) 2.

Magnets: The Bevatron magnet is formed in144 sectors, each 2.5 . They were built independently and are bolted together (Fig. 61 and CA-186-A-116). The magnets' bottom clamp beams rest on jack bolts on top of their foundation; the jack bolts allow for adjustment of the magnet (CA-l 86-A-117). The magnets surround a central aperture, which holds the pole tip and the vacuum chamber through which the beam runs (Fig. 62 and 3. Targets: Experimenters using the Bevatron after the Major Improvement Program could set up experiments in the EPB hall, using the primary beam or secondary beams. It was also possible to place targets in the internal beam within the Bevatron using the Bevatron Travel Target System (referred to as "flipper targets").

Targets were attached to the system, which flipped the target up into the beam during acceleration. The target mechanisms could flip two different targets into position (Fig. 68 and e. Center of Bevatron: The interior wall of the magnet ring is concrete and there is a platform around the interior, providing access to the straight sections (CA-186-A-118). The magnet ring then leaves an open space in the center of the machine. At the center of this space is the center support column for the roof of the building. The column is surrounded by a cast concrete igloo built during the Major Improvement Program to support the roof shielding and the radial crane support structure. 1. Tunnel: The primary access to the center of the Bevatron is via a tunnel from the main floor of Building 51.

The tunnel is accessed by a set of concrete stairs that lead to a poured concrete hallway, which enters the shielded area under the west tangent (CA-186-A-l 2. Igloo: To support the mass of the roof shielding blocks added in the Major Improvement Program, a concrete igloo was poured in the center of the Bevatron, inside the center ring of the magnet (Fig. The igloo is a round poured concrete room with 5' thick walls and a flat roof (CA-186- A-120). 3. Structural support: Steel I-beams form additional support within the center of the Bevatron (CA-186-A-121). They surround the igloo and provide support for the roof shielding blocks in the space between the igloo and the UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 69) interior walls of the magnet.

The beams do not come into contact with any of the equipment or other support structures within the area, maintaining electrical insulation from the magnet itself. 4. Foundation and Deep Tunnel: Major additions to the original foundation were made during the Major Improvement Program to stabilize the machine and support the increased load of the shielding and igloo. To assist in this, a deep tunnel was excavated that circles below the center of the Bevatron to access column bearing points and pour foundations for the roof block support structure. The deep tunnel is accessed by a short spiral staircase that enters a poured concrete tunnel (Fig. 71) that extends to the stairwell to the deep tunnel itself. The deep tunnel houses a rail-and-cart system for transporting equipment (Fig.

72 and CA-186-A-122). f. Tangent Sections: There are straight sections, or tangents, between each of the magnet quadrants. Each of these is a large tank with access ports from the interior of the Bevatron (Fig. g. Vacuum chamber: At the center of the magnets is an aperture into which a metal liner was placed. A vacuum was maintained in the chamber, through which the particles flowed (the internal beamline ). The chamber housed the pole tip magnets and the beam aperture. The original beam aperture was 1' x 4' (Fig. 1. Extraction: As originally built, the Bevatron primary beam remained within the vacuum chamber racetrack and targets were placed inside of it.

One deliberate result of the Major Improvement Program was the ability to extract the beam from the Bevatron and into the EPB hall, where a series of experiments was set up along an external beamline. The EPB hall and the experimental areas in Building 51A have been removed, although the beam extraction point from the west straight section is still apparent with the magnet coil visible outside of the shielding block on the southwest quadrant. a. The beam was extracted by moving it to the edge of its orbit. Magnets were used to manipulate the beam, first spatially recombining the beam particles at the east straight section and deflecting the beam inward to the south straight section. There, it was UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 70) again deflected, sending it to the outer edge of its path where it was extracted before arriving at the west straight section (Fig. However, obtaining an extracted beam with maximum intensity required allowing the beam to accelerate within the Bevatron before moving it out. Internal magnets were plunged into the east and south tangents after the beam was injected and accelerated. Two hydraulic plunging mechanisms were designed and placed at the east and south straight sections (CA-186-A-123, CA-186-A-124, and CA-186-A-125). Known as the mice, they consisted of a long mechanism in a plastic and metal tube on a steel stand extending inward from the inner wall of the straight section toward the concrete igloo (CA-186-A-126 and CA- 186-A-127). b.

The beam emerged from the Bevatron at the entrance to the west straight section and emerged from the exterior shielding structure just past (north of) the west straight section (CA-186-A-128). The stub of the beamline emerging from the shielding structure reveals the magnet casing and the copper coils in epoxy of an external magnet (built ca. (CA-186-A-129, CA-186-A-130, and CA-186-A- 2. Maintaining vacuum: a. Diffusion Pumps: A set of diffusion pumps is visible below the west straight section. The vacuum in the vacuum chamber through which the particle beam moves originally was maintained by twenty- four 32-in oil diffusion pumps (CA-186-A-132).

After the Bevatron was connected to the SuperHILAC to form the Bevalac the vacuum pressure was no longer adequate for acceleration of the heavier beams. These heavier ion beams did not survive long during acceleration and, by the vacuum's limitations were preventing the study of heavier particles, such as uranium. b. A new cryogenic vacuum liner was installed in Made of copper-clad fiberglass in three layers it created an ultrahigh vacuum in the beam orbit UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 71) space of the magnet. Several layers of aluminized Mylar were added outside of the triple-walled vacuum liner to reduce the heat load.

The addition of the three walls to the vacuum and of the layers of insulation reduced the overall inner aperture of the accelerator by about 2.5 cm. D. Site: The Bevatron lA) is built into the hillside with Cyclotron Road splitting on the southwest into Alvarez Road, which continues around to the west, and Lawrence Road, which curves around the south side of the building. The first floor is accessible from the outside on the north and west, while the south side is below ground level on the first floor and only accessible from the exterior on the second floor. There is no significant effort at landscaping. The space between the building and nearby structures to the north is poured concrete, most of it representing the foundation for the former EPB hall.

The hillside rises next to the building's parking areas on the south and east sides. The hillside is covered in grass and scattered trees. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 72) PART III. Sources of Information D. Supplemental Bibliography Alvarez, Luis W. "Recent Developments in Particle Physics." Nobel Lecture. December 11, Bevatron Experimenters Handbook. UCRL 2nd ed. Berkeley: Lawrence Radiation Laboratory, Bevatron Experimenters Handbook. UCRL 2nd ed. Berkeley: Lawrence Radiation Laboratory, rev. Brobeck, William M. Design and Construction of the Bevatron. UCRL-3912. Berkeley: University of California, Radiation Laboratory, Chupp, T. Elioff, and W. A. Wenzel. The Improved Bevatron and Its Performance at High Intensity. UCRL-16228.

Berkeley: University of California, Lawrence Radiation Laboratory, Dobkin, Marjorie, and Michael Corbett. Bevatron and Bevalac, Lawrence Berkeley Laboratory: Historic Architectural Evaluation Report. Report for Purchase Order No. San Francisco: Marjorie Dobkin, Galison, Peter. "Bubble Chambers and the Experimental Workplace." Observation, Experiment, and Hypothesis in Modern Physical Science. Ed. Peter Achinstein and Owen Hannaway. Cambridge, Mass.: MIT Press, UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 73)

Part Iv. Project Information

This report was prepared by Rebecca Ullrich of Sandia National Laboratories under Agreement No. It was created as an addendum to the existing HAER documentation of the Bevatron (Building 51/51A) as part of the mitigation documentation stipulated by the Memorandum of Agreement among the Advisory Council on Historic Preservation, the Department of Energy Oakland Operations Office, and the California State Historic Preservation Office. Dr. Elaine Jackson-Retondo, National Register Programs, National Park Service, West Regional Office stipulated the use of the outline format for this report. It includes only supplemental information for the HABS Outline format, Parts II (focusing on the interior), III, and IV.

In Lawrence Berkeley National Laboratory and the Department of Energy (DOE) completed consultation with the California State Historic Preservation Office and a Memorandum of Agreement with the Advisory Council on Historic Preservation regarding the Bevatron Building. The Bevatron Building lA was found eligible to the National Register of Historic Places. Historic American Engineering Record (HAER) documentation of the Bevatron was prepared in and submitted in That documentation clearly articulated the original conception of the Bevatron and historical information about its design, architects, builders, and historical context. It also made a strong and detailed case for the historic significance of the property.

Additional large-format photographs were taken by photographer Roy Kaltschmidt as part of the HAER documentation. Sabah Hassan provided additional research into and reproduction of building drawings and photographs. Al Smith supplied detailed information about the Bevatron based on his extensive technical experience with it. Dan Kevin, Rick Gough, Al Smith, Jack Heffernan, Nick Peterson, Margaret Goglia, Fred Angliss and Sabah Hassan reviewed the first draft of the report and offered extensive feedback. Margaret Goglia of Facilities Division oversaw the first phase of the project. Sarah Morgan provided administrative support, John Patterson undertook reproduction of building drawings, and Joseph Harkins oversaw the project during the final phase.

June UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 74) FIGURES The following figures are referenced in the text of the report above. Figure 1 BEV-244 (original negative located in Photo Lab Collection). Photographer unknown. April 14, GENERAL VIEW, SOUTH SIDE, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 75) Figure 2 51 key plan (CAD drawing in Facilities Division). April 28, PLAN OF MAIN FLOOR B-51-51A. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 76) Figure 3 51 key plan (CAD drawing in Facilities Division). November 24, PLAN OF SECOND FLOOR lA. z 0 (f) > 0 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 77) Figure 4 51 key plan (CAD drawing in Facilities Division). May 5, PLAN OF BASEMENT LEVEL B-51-51A. ., CQ I , a.. i a: I I {!) i lO ,JI ~ : f ~;; - <' !i '-' ..i\ )~ ifc , z Q (/) > 0 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 78) Figure 5 BEV-203 (original negative located in Photo Lab Collection). Photographer unknown. February 8, CONSTRUCTION OF CENTRAL COLUMN FOR BEV BUILDING. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 79) Figure 6 BEV-323 (original negative located in Photo Lab Collection). Photographer unknown. September 29, INTERIOR MAGNET ROOM, BEVATRON BUILDING. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 80) Figure 7 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, BASE OF CENTER COLUMN, INNER IGLOO AREA, LOWER LEVEL, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 81) Figure 8 BEV-247 (original negative located in Photo Lab Collection). Photographer unknown. April 22, INTERIOR OF BEVATRON BUILDING, CRANES. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 82) Figure 9 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, EXTERIOR STAIRWAY TO CONCRETE PAD, MECHANICAL SECTION, BUILDING 51, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 83) Figure 10 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, EXTERIOR STAIRWAY TO MECHANICAL SECTION, BUILDING 51 BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 84) Figure 11 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, EXTERIOR STAIRWAY TO MECHANICAL SECTION, BUILDING 51, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 85) Figure 12 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, STAIRWAY FROM MAIN FLOOR GENERATOR ROOM TO SECOND FLOOR SWITCHGEAR AREA, MECHANICAL WING, BEVATRON.

UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 86) Figure 13 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, STAIRWAY FROM MAIN FLOOR OF MAGNET ROOM (NEAR LOCAL INJECTOR) TO FAN ROOM MEZZANINE ON SECOND FLOOR OF MECHANICAL SECTION, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 87) Figure 14 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, STAIRWAY BETWEEN BASEMENT (GENERATOR PIT AREA) TO FIRST FLOOR OF MECHANICAL SECTION, GENERATOR ROOM, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 88) Figure 15 Photograph (digital image maintained in Photo Lab Collection).

Roy Kaltschmidt, photographer. June, STAIRWAY BETWEEN FAN ROOM AND CATWALK, SECOND FLOOR, MECHANICAL SECTION, BEV ATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 89) Figure 16 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, EMERGENCY EGRESS STAIRWAY BETWEEN MAIN FLOOR OF MAGNET ROOM AND UTILITY CATWALK, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 90) Figure 17 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, TOP OF LADDERWAY FROM TOP OF BEVATRON ROOF SHIELDING BLOCK INTO CENTER OF BEV ATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 91) Figure 18 BEV-3302 (original negative located in Photo Lab Collection). Photographer unknown. February4, BEVATRON ALTERATION COMPLETE INSIDE IGLOO, STAIRWAY TO BEAM LEVEL ON RIGHT. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 92) Figure 19 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, STAIRWAY BETWEEN BEAM LEVEL AND LOWER LEVEL OF BEVATRON CENTER. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 93) Figure 20 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, LADDER TO UTILITY TUNNEL, MAIN FLOOR, BEV ATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page 94) Figure 21 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, STAIRWAY BETWEEN MAIN LEVEL AND ENTRANCE TO DEEP TUNNEL, EXTERIOR BUILDING 51, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 95) Figure 22 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, BLOCKED ENTRANCE AND STAIRWAY TO DEEP TUNNEL BELOW MAIN FLOOR, BUILDING 51, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 96) Figure 23 Photograph l (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, STAIRWAY BETWEEN ENTRANCE TUNNEL AND DEEP TUNNEL TO FOUNDATION, BUILDING 51, BEVATRON.

UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 97) Figure 24 BEV-1797 (original negative located in Photo Lab Collection). Photographer unknown. May 11, SHIELDING FOR NEUTRONS; CABLE RACEWAYS UNDER WINDOWS ON LEFT, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 98) Figure 25 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, UTILITY TRENCHES, MAGNET ROOM FLOOR, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page 99) Figure 26 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer.

June, UTILITIES SUPPORTING COOLING SYSTEM BETWEEN FAN ROOM AND PASSAGEWAY UNDER BEVATRON, ROOM 10, MAIN FLOOR, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 27 No. 8Q9074A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). February 19, Indicates which sections of the drawing have been reproduced as Figures 28 and 29. BEVATRON SHIELDING, STUDIES FOR 10 13 PARTICLES/PULSE PROTECTION, INJECTOR SHIELDING, STUDY #1. Figure 29 Figure 28 l ' 1. i t I 'I UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 28 Section ofDwg. No. 8Q9074A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection).

February 19, BEVATRON SHIELDING, STUDIES FOR 10 13 PARTICLES/PULSE PROTECTION, INJECTOR SHIELDING, STUDY #1. / / .. - .Ill' BliH!N?ll UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 29 Section ofDwg. No. 8Q9074A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). February 19, BEVATRON SHIELDING, STUDIES FOR 10 13 PARTICLES/PULSE PROTECTION, INJECTOR SHIELDING, STUDY #1. I UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 30 BEV-680 (original negative located in Photo Lab Collection). Photographer unknown. February 5, IN\CTOR IN PLACE, TANK CLOSED-GENERAL VIEW, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO.

CA-186-A (Page Figure 31 BEV-3769-C (original negative located in Photo Lab Collection). Photographer unknown. April 1, BEV ATRON CONTROL ROOM. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 32 BEV-819 (original negative located in Photo Lab Collection). Photographer unknown. December 15, INJECTOR CONTROL UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 33 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. March, ENTRY TO ROOM 11, INJECTOR CONTROL ROOM, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 34 No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection).

April 23, Indicates which sections of the drawing have been reproduced as Figures 35, 36, 37, and 38. BEVATRON 10 13 SHIELDING, WALL BLOCK ASSEMBLY, DEVELOPED VIEW, UADS I II & IV SOUTH & EAST TANGENTS. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 35 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). April 23, BEVATRON 10 13 SHIELDING, WALL BLOCK ASSEMBLY, DEVELOPED VIEW, QUADS I, II, & IV, SOUTH & EAST TANGENTS. .l l. i ~ ~ ~ '. ~ :i. y' \!I~ { ~ @, 0 ' ! ., t. . t . t,z ~ ~ J ~ ' ~ i ~ UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 36 Section ofDwg. No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). April 23, BEVATRON 10 13 SHIELDING, WALL BLOCK ASSEMBLY, DEVELOPED VIEW, QUADS I, II, & IV, SOUTH & EAST TANGENTS. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 37 Section of No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). April 23, BEVATRON 10 13 SHIELDING, WALL BLOCK ASSEMBLY, DEVELOPED VIEW, QUADS I, II, & IV, SOUTH & EAST TANGENTS. ~ s ,,J i ~!1 ! ~ ~ . J ~ ~- ~l~ .-~ + c:i. ' ~ ~ ~ ".; ... .; ~ l t! ~ ~ ~ "~ ~"' -- :. ,. ~ ;~:i ~ . ,., .. ~ ~'l>i;: , --, ff';:r.;Yl:I UNNERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 38 Section ofDwg. No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). April 23, BEVATRON 10 13 SHIELDING, WALL BLOCK ASSEMBLY, DEVELOPED VIEW, QUADS I, II, & IV, SOUTH & EAST TANGENTS. . .t cy ~fl ~ ~~ " ~ " ,_ I> f i UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 39 No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). June 21, Indicates which sections of the drawing have been reproduced as Figures 40, 41, 42, and 43. SHIELDING WALL 10 13 WALL & EXIT TYPE A, STUDY NO. 1. Figure 41 Figure 40 Figure 42 Figure 43 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 40 Section of No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). June 21, SHIELDING WALL 10 13 WALL & EXIT TYPE A, STUDY NO. 1. - . f. . " - .~ - ... ~- ... ' .. . . . ... ' , \ \ \ \ \ '\ \ , \\. \'. \ ~ .. \ . ~ :\ ~. :r/ - . :. ~)I,~1 . t . .. ~ ' .! .J l. UNNERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 41 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). June 21, SHIELDING WALL 10 13 WALL & EXIT TYPE A, STUDY NO. 1. ,.. - ... ~ ~ ~ - .. ~. -- - I \ \ UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 42 Section of No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). June 21, SHIELDING WALL 10 13 WALL & EXIT TYPE A, STUDY NO. 1. \ . "' -~. . ,r:t.IB~=: . ; , 1/ UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 43 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). June 21, SHIELDING WALL 10 13 WALL & EXIT TYPE A, STUDY NO. 1. ,. 3. ' ~~I I 'I ,I :. ~ ., I _J . ..~ ~1 , .. II) UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 44 No. Engineering drawing (original drawing location in Architecture and Engineering As-Built Collection).

September 28, Indicates which sections of the drawing have been reproduced as Figures 45, 46, 47, and 48. BEVATRON 10 13 SHIELDING, ROOF BLOCK ASSEMBLY, PLAN. Figure 48 Figure 46 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 45 Section of No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 28, BEVATRON 10 13 SHIELDING, ROOF BLOCK ASSEMBLY, PLAN. ~ .._ - - - - - - - <: "' //Y"?o' .I ?. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 46 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 28, BEVATRON 10 13 SHIELDING, ROOF BLOCK ASSEMBLY, PLAN.

/N '' .it'-!." / UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 47 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 28, BEVATRON 10 13 SHIELDING, ROOF BLOCK ASSEMBLY, PLAN. I; I ~~I I 1 "( \ ~ ~ UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 48 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 28, BEVATRON 10 13 SHIELDING, ROOF BLOCK ASSEMBLY, PLAN. ~ ' ~ ~~ i(j ." ~ ~ ~11 ~ :~ " " / UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 49 No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 29, Indicates which sections of the drawing have been reproduced as Figures 50, 51, 52, and 53. BEVATRON 10 13 SHIELDING, OUTER RING ROOF,

Block No

Figure 52 UNNERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 50 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 29, BEVATRON 10 13 SHIELDING, OUTER RING ROOF, BLOCK NO. . \:. \\\ r~ 11 ~ jl ~ ' ~ ' i . i~ . ,,; . " :.. :.. .. . . . '}. . UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 51 Section of No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 29, BEVATRON 10 13 SHIELDING, OUTER RING ROOF, BLOCK NO. I, .. '"I l ! : I i i I i I j I -~, . 1-- ' I I ... UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 52 Section of No.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 29, BEVATRON 10 13 SHIELDING, OUTER RING ROOF, BLOCK NO. i'\ ti. ~~ ' ~ :I ~ - ! " ! I .. . : /. I I I n 11 ."' ~ .3i" ~ ~ ~ / --" ' \_ \ .. I .. '- "- f n"" '- I I I - - - - ~ - - -- - ..l i i I i-<- J':f{I.? J iI ~ . -- 1 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 53 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). September 29, BEVATRON 10 13 SHIELDING, OUTER RING ROOF, BLOCK NO. ~~ ~+ I ' --. - -I- - - ~-- I ~i I : .i~ I I . I ' I . i~~ I ; "" { I ~~~ ~~ ~ I ~ I \ ' I c ~- ' I ' I I 'l I I I:-:- /. /_ ' . - -. I I .. ~ I I ;'i 1 i " "- I j :I' ! .~ ~ ., I I , . J.

k - ' - \ I~ fi- ,f .j: ::. .: -.. ' ' I ~~ l j\ y i '; l - J - ~ -~ ' ! - ;I c'- --- -l- --I - i- c-- ~ ) -- UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 54 No. 9N6266A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). November 10, Indicates which sections of the drawing have been reproduced as Figures 55, 56, 57, and 58. BEVATRON 10 13 SHIELDING, TANGENT AREA ROOF,

Outer Ring Roof Blocks-Sections

Figure 56 Figure 55 Figure 57 UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 55 Section of No. 9N6266A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). November 10, BEVATRON 10 13 SHIELDING, TANGENT AREA ROOF, OUTER RING ROOF BLOCKS-SECTIONS. --- - - - - - - - I .3 .; J! p .. j'. " :. -t . , ~~ . ' . . -:. _, ' .:: = UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 56 Section ofDwg. No. 9N6266A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). November 10, BEVATRON 10 13 SHIELDING, TANGENT AREAROOF,OUTERRINGROOF BLOCKS-SECTIONS. I I . I I I I I \I I I i: I I 1 ! \\ /I \\ I I ;l I I .. ."' 0" ~ ' ~ l .(~ I!!

,, ~~ i .l :;" % ~ 0 ~. ... -> J 0- --. \ / ,; .~ :. ~. :. :~~ UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 57 Section of No. 9N6266A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). November 10, BEVATRON 10 13 SHIELDING, TANGENT AREA ROOF, OUTER RING ROOF BLOCKS-SECTIONS. ' ;~ .. .., " -~ i UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 58 Section ofDwg. No. 9N6266A. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). November 10, BEVATRON 10 13 SHIELDING, TANGENT AREA ROOF, OUTER RING ROOF BLOCKS-SECTIONS. ' ; .: . "' . . .f .~ .. . .' ' ,.. : .. ').:i .. r . .:; . 'i % ~l. ~ ~ . ;;" . ~ .

.,s :, UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 59 BEV-288 (original negative located in Photo Lab Collection). Photographer unknown. August 1, MAGNET ROOM INTERIOR, BEV A TRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 60 BEV-295 (original negative located in Photo Lab Collection). Photographer unknown. August 25, BEVATRON, INTERIOR OF MAGNET ROOM. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 61 BEV-1653-C (original negative located in Photo Lab Collection). Photographer unknown. October 20, OVERALL OF BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 62 No. 3Ll 93 lB.

Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). December 14, BEVATRON MAGNET TERMINOLOGY . i!.1'!:.. < , , In. . ., nr .Jq -ot,.i .I ""' 2 ~li :I ILf'., \.I 4i ~. .<if !l. ~ ~ w ~ :;. ~ W, < ;lt 9 ., r ~iU r~ f - 1 ' UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 63 No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). August 25, Indicates which sections of the drawing have been reproduced as Figures 64, 65, 66, and 67. BEVATRON, MAGNET CORE,

Erection Drawing

Figure 66 Fig ire 67 ' ~ l 4 I i I UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 64 Section ofDwg. No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). August 25, BEVATRON, MAGNET CORE, ERECTION DRAWING. ~ - O:;t>Clliorj ; ~ : < :., ,.. "i (1) ,:. .1, 0 a a 11 ~ .. : ,.. . ?:' P-' = tn ~.. 0 '"! ~: . " (1) "~ t, tn~o ' ?:' i= H; Ul tn (il u () !>" ~ >-l p (Jq >-< . 0 tn zp z 0 (Jq u ... w ?:' ~ ~ ~ s ~ 0\ I tn to s. o.s. ()~ .,---i.1NEi. D-D D AJ?e pvNc/fED ON 0 :1. . Bif.J;ltYtfC. C0Nse,evrtve .. ;.,G!f6E Pourrs/JlfES AT it.94.,,, . PO/NiS D SO A SJ:lf:AIGHT LIN!:. (1) (Jq ~Fvilc11 P..01im D ~ "i J<IJ"r t 0 !>" ~ ~- ... ~ >.~ 3 i= ~~ 4 (Jq 0 [/J ~~ i= ff '\STRAIN rn "i !.& . eT"tN' -: .!

(Jq i--J I ~ W!:ENt:H,.. INGE't:tSOi...t: ~~A!:iD !" N 5 -: _. -~- . ~H ~ 7 . ~~ ~ --< - d ..fi&:..ii<r 'HJ:ENCH,..llf"G. . -RA,Y~S.s=~:.-r-. - -:-.~i >ro :..E~Hl!TN'P.~I~~- - -. : . l.O "i trJ > Ul !>" 2; o~ ~ to n . .+ :~~;:i:~~~~;~r1~6;z~;~.i.,.. :. .. zo> f : -rPOWER~~SiiDiii'Vl~.~ .~ , till.fr:--:::.. : Ct; s 0 ~ t: .. : tn~ . > =~ . ! .. , <o n i--J o > >-l ..+ >o~ ?:' 8.. ~~z , ~. ~; ~'- ;: /{: .. :Ji'. r 00 --< ,. . . z " r I '"to~> ~!till~ ~-~ > trJ >r ~< ~ (TO ._] > (D i--J woo ~zz UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 66 Section of No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). August 25, BEVATRON, MAGNET CORE, ERECTION DRAWING . .i :i '. ' .. ~ : ... . .. ~.: . . ~ . . . .

IJ.J8" ~ .. s i.J~~ ~ ; ' ~Q, " ~ .. .., ... ~.~ ~- IJ~ ' 4 Ii ~ ; " IU ~ ~ S:B ~ ~ta~~'<' " . er~~~; a:; .. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 67 Section of No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). August 25, BEVATRON, MAGNET CORE, ERECTION DRAWING. UNNERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 68 BEV-1455 (original negative located in Photo Lab Collection). Photographer unknown. February, DRAWING OF FLIP-UP TARGET, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 69 BEV-3551 (original negative located in Photo Lab Collection). Photographer unknown. April 22, TRAVELING TARGET ASSEMBLY.

UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 70 Cross section illustrates roof trusses, Bevatron roof shielding over quadrants, and igloo (at center). Digital image of drawing. Nick Peterson, architect. April 11, CROSS SECTION SCHEMATIC OF BUILDING 51 WITH IGLOO AT CENTER, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 71 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer. June, TUNNEL TO DEEP TUNNEL ACCESS, VIEW OF STAIRWAY ENTRANCE, BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 72 Photograph (digital image maintained in Photo Lab Collection). Roy Kaltschmidt, photographer.

June, DEEP TUNNEL INTO FOUNDATION UNDER BEVATRON. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 73 No. Engineering drawing (original drawing located in Architecture and Engineering As-Built Collection). January 15, BEVATRONMISC. GENERAL, TANGENT AREA PLATFORMS, EAST TANGENT AREA PLATFORMS, STAIRS & RAILS. 'fi "D J) M . "" ~ ~ ~ . g ., ii. D ~.r u I.I li(> t- "i uti.. ] (j 0"" ~Yi~ i~J ~ ~~ ill J. l1 I) ( ~l ~~ t~~ ua ~~ [l_ '\1 G C ! ~ i J. .. 1 !J ~'~ ~ I ""~ ' ,, 11! 11i , V ~I{' ,. < 1 J. ~ '""'i.< ,, " J .( 1 ~~. ~ ~ i l p !l" , Il " I d 2 )_ ~~ " << ~ :2 , ;~ ~1~ ". ;~ ; '" . ,:: l !. fl i.1( < .J ti , I ' t ::: "' ! '.: ~ .} 0 fl "' 0 ~ ~ ~ ~) i ~ r ,~4 t;: ~ f} ., n I [I " ~~I .j 0 &1 (_; .z ('i Ill ,, ) ; ~ , j.

L UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 74 BEV-1474 (original negative located in Photo Lab Collection). Photographer unknown. February 27, FLIP-UP TARGETS AT NORTH OUTLET. UNIVERSITY OF CALIFORNIA RADIATION LABORATORY,BEVATRON HAER NO. CA-186-A (Page Figure 75 Figure 1 from Bevatron Experimenters Handbook, UCRL ed. (Berkeley: University of California, Lawrence Radiation Laboratory, LAYOUT OF THE INTERNAL DEFLECTION SYSTEM. f T ! r -1 B:i Pi~~:. ~ .~J1ternn: d~fle~:tJ_or; Tne circuJ:tLting b(.:._az; r,;avels . " . ' .' - LT: t c._oc1,:w1G{: c:1 :cc::~::)IL

In context

Berkeley, California The place record: every map, photograph and survey of this town.
Alameda County, California 231 topographic sheets across the county.
Library of Congress record The original filed report as the survey filed it.

Also surveyed in Berkeley

10 records

The federal surveyors worked through Berkeley building by building. These are the other structures they measured and filed a report on, longest report first.

SheetStructure SurveyReport
Fleming GardenHALS CA-4327,081 words
Berkeley Public LibraryHABS CAL,1-BERK,5-8,536 words
Marsh-Sperry GardenHALS CA-1726,679 words
University of California Radiation LaboratoryHAER CA-186-B5,575 words
Berkeley Women's City ClubHALS CA-464,816 words
Davis-Byrne BuildingHABS CAL,1-BERK,3-4,695 words
Piedmont Way & the Berkeley Property TractHALS CA-23,878 words
Berkeley City HallHABS CAL,1-BERK,2-2,601 words
Greenwood CommonHALS CA-12842 words
Peralta HallHABS CAL,1-BERK,1-34 words

Provenance

  • Written history. Quoted verbatim from HAER CAL,1-BERK,4-. United States federal work, no copyright under 17 U.S.C. 105.
  • Text capture. Machine-read from the scanned typescript filed with the survey, so spelling and spacing follow the original page.
  • How this page is made. Documentary passages are quoted from the linked federal record; page labels and counts are clearly marked as site presentation or calculations.