The National Covered Bridges Recording Project is part of the Historic American Engineering Record (HAER), a long- range program to document historically significant engineering and industrial works in the United States. HAER is administered by the Historic American Buildings Survey/Historic American Engineering Record, a division of the National Park Service, U.S. Department of the Interior. The Federal Highway Administration funded the project. POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 2) Chronology America's first covered bridge built at Philadelphia Gold discovered in California John T.
Little builds California's first covered bridge Pierre Sainsevain erects sawmill at this site Henry van Valkenberg establishes San Lorenzo Paper Mill at this site John Baird of San Francisco organizes the California Powder Works. Robert W. Smith patents Smith truss California Powder Works expands complex Robert W. Smith obtains a second bridge truss patent. California Powder Works purchases the former San Lorenzo Paper Mill property. Bridges over San Lorenzo River destroyed by floods Powder Works Bridge built Robert W.
Smith dies Powder Works closes at Santa Cruz Paradise Park Masonic Club purchases property Railroad tracks removed from bridge Covered bridge plaque dedicated Extensive repairs to covered bridge Covered bridge centennial observed; sprinkler system installed Powder Works Bridge recorded by the Historic American Engineering Record POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 3) Introduction Within a year of the discovery of gold at Sutter's Mill at Coloma in the population of California tripled. The urgent demand for roads and bridges was initially met by the establishment of privately financed ferries, turnpikes and toll bridges. In John T. Little of Castine, Maine, built California's first covered bridge at Salmon Falls.
By there were at least one hundred toll bridges in the gold mining region of California. The majority of these were timber truss bridges and, presumably, many of them were covered. Overtime, however, the covered bridges were replaced with new structures, or lost to floods, fires, vandalism, neglect or decay. By there were still thirty covered bridges in California.1 That number dropped to 17 by Today there are 9 historic covered bridges in California:3 WG Bridgeport4 Nevada County, CA Howe truss Virginia Turnpike Co. WG Knight's Ferry5 Stanislaus County, CA Howe truss Schuylkill Construction Co. WG Powder Works Santa Cruz County Smith truss Pacific Bridge Co.
WG Wawona6 Mariposa County Queenpost truss Galen Clark WG Oregon's Creek Yuba County, CA Queenpost truss Thomas Freeman WG Felton Santa Cruz, CA Warren truss Cotton Brothers & Co. WG Honey Run7 Butte County, CA Pratt truss American Bridge Co. WG Berta's Ranch Humboldt County, CA Queenpost truss WPA WG Zane's Ranch Humboldt County, CA Queenpost truss WPA 1 S. Griswold Morley, The Covered Bridges of California (Berkeley: University of California Press, Richard Sanders Allen, "Covered Bridges in California," Connecticut River Valley Covered Bridge Society Bulletin 2 (June 5. 3 California also has several non-authentic or non-historic covered bridges that have appeared in recently published lists, including: Aptos Creek Bridge Jacoby Creek Castleberry Roaring Camp and Brookwood 4 See HAERNo.
CA-41, Bridgeport Covered Bridge (including Addendum) and HABS No. CA-1401, Covered Bridge. 5 See HAER No. CA-314, Knight's Ferry Bridge and HABS No. CA-158, Covered Bridge. 6 See HAER No. CA-106, Wawona Covered Bridge. 7 See HAER No. CA-312, Honey Run Bridge. POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 4) Description The Powder Works Bridge was originally built as a single-span Type 48 Smith truss wooden covered bridge. It is now supported at its center by an open-column pier, making it a continuous, two-span structure. The total length of the bridge is 164 feet.
The truss is high from the top of the upper chord to the bottom of the lower chord and wide overall, with a roadway width of The truss is fourteen panels long, each panel measuring approximately center-to-center. There is a concrete slab approach culvert at the westerly end and a concrete slab approach culvert at the easterly end. The trusses are framed in a manner designed in the mid-nineteenth century by Robert Smith of Ohio. The upper chord and lower chords are four lines of timbers in the upper chord; in the lower chord), laid flat and bolted together with shear blocks between them. The chords are connected by vertical endposts and paired wooden diagonal members with single wooden counter braces intersecting at opposing angles at mid-truss height the full length of the truss.
The trusses are bolted at each intersection with %" diameter threaded rods fastened with nuts. The diagonal members and upper chord are notched into each other and bolted through the chord. Diagonal iron rods (presumably a later addition) are paired with the single timbers and single with the paired timbers. Their diameter varies from %"to with no easily observable pattern (%" or 1" rods appear typical). Each rod passes through the upper and lower chords where it is fastened with a plate and nut. The floor system includes paired transverse wooden floor beams, spaced approximately 20" apart and seated on the lower chord. Wooden lateral cross bracing between the lower chords is secured with cast iron bearing blocks and bolts. There are no stringers.
Longitudinal flooring is laid directly on the floor beams, with running boards on top. There is a 3' wide walkway on the northerly side of the roadway inside the bridge. The truss is braced overhead with tie beams between the end posts and lateral bracing between the upper chords along the length of the truss. There are sway braces between the end posts and tie beams. Rafters are spaced at approximately 2 feet on center and frame onto the upper chord. A gable roof overhangs the eaves and portals and is covered with corrugated metal roofing fastened to wooden nailers on top of the rafters. Metal pipes for a sprinkler system run the length of the bridge and electric light fixtures have been installed at the center of the bridge and over the portals.
The exterior of the bridge is covered with board and batten siding to the eaves. The sheathing is fastened to wooden nailers on the outer faces of the trusses. There are three diamond windows with glass panes on each side of the bridge. The portals have slightly curved openings and bow forward over the approaches. Warning signs, headache bars and flashing traffic lights have been installed at both ends of the bridge. Robert Smith patented two different truss designs in (Type I) and (Type 2) and later developed a reinforced variation (Type 3) and another improved variation (Type 4). POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 5) The current abutments are poured concrete (the originals were reportedly heavy timber braced piles) with short angled wingwalls.
An open two-column poured concrete pier has been added to support the center of the span. There are wooden bolster beams over the pier. The bridge is still used by vehicles and pedestrians, and is currently load rated for 5 tons at 5 History The discovery of gold in California in brought a growing demand for blasting powder for mining and railroad construction. In a group of San Francisco capitalists incorporated the California Powder Works to provide blasting powder for the Central Pacific Railroad. The company purchased a former paper mill site on the San Lorenzo River at Santa Cruz on which to build the powder works.
The site offered relative isolation, water power, a good supply of timber, and proximity to a labor force.9 Construction at "Powder Mill Flats" began in February and by May the mill was producing kegs of powder.10 Demand for the company's products was so great that the complex was expanded in with the construction of seventeen new buildings.11 By the 200-acre site contained 21 powder mills, 10 shops, 10 wheelhouses, 6 magazines, a copper shop, a boarding house, a school, a powder house, and 35 other buildings.12 The first bridge at this site was a simple plank bridge built at an unknown date in the mid- nineteenth century.13 By an uncovered timber truss bridge had been constructed at this site.14 When that bridge washed out in a flood in December the company contracted with the Pacific Bridge Company of Oakland for a more permanent structure.16 The new bridge was fabricated in Alameda, shipped to the site by rail, and erected in the spring of by the Pacific Bridge Company of Oakland.17 At the time of its construction, it was the longest single- span bridge in Santa Cruz County and was sturdy enough to accommodate the narrow-gauge 9 Chamberlain, "California and the Three Bears: The History of the California Powder Works," The Gun Report, January 22.
10 E.S. Harrison, History of Santa Cruz County (San Francisco: Pacific Press Publishing Company, 11 Titus Fey Cronise, The Natural Wealth of California (San Francisco: Bancroft & Co., 12 Wallace W. Elliot, Santa Cruz, California, Illustrations with Historical Sketch of the County (San Francisco, 13 "Powder Mill Canyon," Santa Cruz Daily Surf, 12 May 6. 14 "Map of the California Powder Works, Erected 15 Santa Cruz Sentinel, 30 December 16 Bruce R. Way, The Life and Careers of William Henry Gorrill: (Lanham, Maryland: University Press of America, 17 J. Nelson, "Short History of the California Powder Works and Paradise Park Present), typescript, Collection of the McPherson Center Museum of Art & History, Santa Cruz, California.
POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 6) railway that ran through the company's property. On May 4, the Santa Cruz Sentinel reported the completion of the new Powder Works Bridge: As the bridge is 168 feet in length and has but one span it deserves something more than a passing notice. The bridge is a Smith patent high truss. The truss is 18 feet in height, with top chords of four leaves, each and bottom chords, same number of leaves The width of the bridge is 20 feet, enabling the Powder Company to put down a car-track without conflicting with wagon travel. The entire structure is of the best workmanship throughout.
It will sustain pounds to each lineal foot, which, distributed over its surface, would be more than 80 tons, and is capable of sustaining a moving load of much greater weight than will ever be required of it. The piers at each end are of very heavy piles, well driven, and capped and braced in the most thorough manner. ... We believe it is designed by the Powder Company to enclose and roof the bridge, thereby more than doubling the life of the entire structure. In Dupont Company purchased the California Powder Works. In the California Powder Works became part of the Hercules Powder Company, and operations were moved to a more modern facility at Hercules, California. Much of the powder works complex at Santa Cruz was subsequently demolished.
In the former California Powder Works property was purchased by members of the Fresno Masonic fraternity for the establishment of a summer cottage colony for its members. They named the site "Paradise Park," because of the beauty of the natural surroundings.19 Today, many residents live in Paradise Park year-round. Among the cottages and trees, a few vestiges of the former Powder Works complex remain, including the covered bridge. No primary written records have been found concerning repairs and alterations to the bridge, but some information is contained in secondary sources. The deck and roof have been replaced, and lights were installed at an unknown date. In the the railroad tracks were removed from the bridge.
Extensive repairs were undertaken in in anticipation of the bridge's centennial in The Powder Works Bridge remains in use as an integral part of a thriving residential community. Design In Ohio native Robert W. Smith patented a wooden bridge truss with parallel upper and lower chords connected by a series of diagonals and counter diagonals. The Smith truss was the most successful of several post-Civil War timber truss designs that, for a short time, made wood bridges competitive with iron bridges. Smith built his first covered bridge in in Miami County, Ohio, and shortly thereafter, established the Smith Bridge Company at Toledo.20 18 "California Powder Works Bridge," Santa Cruz Sentinel, 4 May 3. 19 "Powder Mill Canyon," Santa Cruz Daily Surf, 12 May 6. 20 Clark Waggona, ed.
History of Toledo and Lucas County (New York: Munsell & Co., POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 7) Bridges were prefabricated to order, shipped to the site, and erected under the supervision of a company agent. In addition to manufacturing the Smith truss, the company also built Howe and Warren trusses and was among the early builders of other combination wood and metal and all metal bridges. While not as popular as the Howe truss, perhaps hundreds of Smith trusses were built in at least nine states, being most popular in the Midwest and on the west coast. Gradually, there was increased competition from companies manufacturing iron bridges.
The cost-effectiveness of iron, which had a 60-percent longer service life, led to the eventual abandonment of the Smith truss design in the late nineteenth century. The Smith Bridge Company manufactured bridges (including iron ones) until when the works were sold to the Toledo Bridge Company. Robert Smith died in at the age of 63. In the mid-twentieth century, mechanical engineer Raymond E.
Wilson of Swarthmore, Pennsylvania, studied the Smith truss and categorized its variations as follows: Type 1 was based on the patent where the center panel had crossed diagonal members; Type 2 was based on the patent and had opposing diagonals meeting at the center panel; Type 3 was similar to Type 2, but was reinforced with extra diagonal braces at the center panel; and Type 4 had double diagonals the full length of the bridge intersecting with single counter diagonals.21 Types 3 and 4 were most commonly used.22 Of the twenty extant Smith truss covered bridges, 90 percent are located in Ohio and Indiana. There are no known surviving examples of Type 1.
The Powder Works Bridge is an excellent example of the Type 4 Smith truss, and the only surviving example of a Smith truss in the western United States. Builder Ohio lawyer William Henry Gorrill did legal work for the Smith Bridge Company in After suffering a bout of tuberculosis, Gorrill headed to California to regain his health, where he became an agent for the Smith Bridge Company. In Gorrill established the Pacific Bridge Company at Vallejo, advertising its specialty as "all kinds of wooden bridges on Smith's Patent truss plan."23 In April the company landed a significant contract for a 416-foot bridge at Oroville.
Following its successful completion, the company's business boomed and in they expanded their operations to include a permanent mill yard in San Francisco, where they could cut their own timbers.24 In the spring of the company began offering iron bridges as an option for their customers. Though they continued to build wooden bridges, the company eventually abandoned the Smith truss. 21 Miriam Wood, The Covered Bridges of Ohio: An Atlas and History (Columbus: Old Trail Printing Company, 22 Wilson, Raymond E. "The Story of the Smith Truss," Covered Bridge Topics 25 (April 5. 23 "The Smith Patent Truss Bridge," Mining & Scientific Press: An Illustrated Journal of Scientific and Industrial Progress, 11 March 24 Mining & Scientifc Press, 20 April 1.
POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 8) Following William Henry Gorrill's death September 12, his brothers took over the firm. In the they opened another office in Portland, Oregon, and established a partner firm, Pacific Construction Company, at San Francisco. The Pacific Construction Company remained a major contracting firm into the with contracts that included piers for the Golden Gate and Oakland Bay bridges and major highway bridges across the Willamette and Columbia rivers.25 The Pacific Bridge Company is noteworthy as a bridge-building firm that began building wooden spans in the nineteenth century and successfully made the transition to steel and concrete spans in the twentieth century.
25 Way, POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 9) Surviving Smith Truss Covered Bridges Kidd's Mill Bridge Mercer County, PA Smith 2 truss Smith Bridge Co.? Brushy Fork Bridge Jackson County, OH 74'Smith 2 truss J.G Stengall Locust Creek Bridge Pocahontas County, WV 116'Smith 4 truss Bruce Buckeye Furnace Bridge Jackson County, OH 59' Smith 3 truss Dency, McCurdy & Co. Powder Works Bridge26 Santa Cruz County, CA 180'Smith 4 truss Pacific Bridge Co. North Manchester Bridge Wabash County, IN 150'Smith 4 truss Smith Bridge Co. Byer Bridge Jackson County, OH 74' Smith 3 truss Dency Buckskin Bridge Ross County, OH 99' Smith 3 truss Smith Bridge Co.
Spencerville Bridge DeKalb County, IN 160'Smith 4 truss John McKay Otway Bridge Scioto County, OH 127'Smith 3 truss Smith Bridge Co. North Pole Road Bridge Brown County, OH 169'Smith 4 truss Smith Bridge Co. Vermont Bridge Howard County, IN 111'Smith 3 truss Old Red Bridge Gibson County, IN 170'Smith 4 truss Washer Mary Ruffner Bridge Perry County, OH 78'Smith 3 truss Rinard Bridge Washington County, OH 130'Smith 3 truss Smith Bridge Co. Cataract Falls Bridge Owen County, OH 140'Smith 3 truss Smith Bridge Co. Wheeling Bridge Gibson County, IN 164'Smith 4 truss Washer Engle Mill Road Bridge Greene County, OH 146'Smith 3 truss Stevenson Road Bridge Greene County, OH 98' Smith 3 truss Smith Bridge Co. Brown Bridge Brown County, OH 146'Smith 4 truss Smith Bridge Co.
George Miller Bridge Brown County, OH 154'Smith 4 truss John Griffith 26 See HAERNo. CA-313, Powder Works Bridge. POWDER WORKS BRIDGE (Paradise Park Bridge) HAERNo.CA-313 (Page 10) Sources "California Powder Works Bridge," Santa Cruz Sentinel, 4 May Elliot, Wallace W. Santa Cruz California Illustrations with Historical Sketch of the County. San Francisco, Harrison, E.S. History of Santa Cruz County. San Francisco: Pacific Press Publishing Company, "Map of the California Powder Works, Erected Moore, E.S. "The California Powder Works, Santa Cruz, California." Cincinnati: Strobridge & Co. Lithographers, Neff, Eldon M. "Highlights in the Life of Robert W.
Smith," Buckeye Bridge Briefs 4 (December "Powder Manufactory," Nevada Democrat, 1 January "The Powder Mill at Santa Cruz," Pajaro Times 1 Reedy, Thomas L. and Alice M. Reedy. In the Beginning: A History of the Paradise Park Site. Santa Cruz: Paradise Park Masonic Club, "Robert W. Smith Is Dead," Toledo Daily Blade, July 7, Santa Cruz Sentinel, Santa Cruz, California, Smith, Robert W. U.S. Letters Patent No. 16 July Smith, Robert W. U.S. Letters Patent No. 7 December "The Smith Patent Truss Bridge," Mining & Scientific Press: An Illustrated Journal of Scientific and Industrial Progress 22 (11 March Watkins, Rolin C. History of Monterey and Santa Cruz Counties, California. Chicago: Clarke Publishing Co., Way, R. Bruce.
The Life and Careers of William Henry Gorrill: Lanham, Maryland: University Press of America, Wilson, Raymond E. "The Story of the Smith Truss," Covered Bridge Topics 25 (April ADDENDUM TO: HAER CA-313 POWDER WORKS BRIDGE HAER CA-313 (Paradise Park Bridge) National Covered Bridges Recording Project Spanning San Lorenzo River, Keystone Way, Paradise Park Santa Cruz vicinity Santa Cruz County California REDUCED COPIES OF MEASURED DRAWINGS FIELD RECORDS HISTORIC AMERICAN ENGINEERING RECORD National Park Service U.S. Department of the Interior C Street NW Washington, DC