BlockBefore

Santa Susana Field Laboratory, Bravo Test Area, 5800 Woolsey Canyon Road, Simi Valley

Santa Susana Field Laboratory, Bravo Test Area, 5800 Woolsey Canyon Road, Simi Valley, Ventura County, CA. Surveyed as HAER CA-2284, with a 2,342-word written history.

From the record

“A portion of the site design was based on a World War II German rocket engine test site.”

Written record, HAER CA-2284 survey. Machine-read text.

Surveyed by the federal HAER program as HAER CA-2284 · the record runs 2342 words · one of 42 surveyed structures published for this county.

Sources: the survey record at the Library of Congress

Location

165 words

Source document Quoted word for word from HAER CA-2284. Not written, edited or summarised by this site.

Woolsey Canyon Road, Simi Valley vicinity and Santa Susana vicinity, Ventura County, California, and Canoga Park vicinity, Los Angeles County, California Coordinates: N 34 o 13' W 118o 41' USGS Calabasas, California There is no restriction on the release of the location information.

Background: Designed in mid-1955, Bravo Test Area included the third cluster of static test stands constructed during The design and construction of the test site was comparable to the four similar test sites at the Santa Susana Field Laboratory Dates of Construction: to Types of Structures: Concrete and structural steel test stands, substations, recording / control centers, pre-test buildings, observation bunkers, fueling facilities, well housings, pump stations Architect/Builders: The original Bravo complex was designed by the Los Angeles architectural-engineering firm of Daniel, Mann, Johnson & Mendenhall with the aid of German engineer Walter Riedel.

Original Owner Occupant and Users: North American Aviation Rocket Engine Test Site United States Air Force Leased to National Aeronautics & Space Administration Formally transferred to NASA in

Significance

85 words

Source document Quoted word for word from HAER CA-2284. Not written, edited or summarised by this site.

A portion of the site design was based on a World War II German rocket engine test site. The Santa Susana Field Laboratory, Bravo Test Area was one of the earliest test complexes in the United States. The Bravo site was an exceptional scientific research, development, test and evaluation site. During the latter half of the twentieth century, the laboratory supported rocket engine development for weapons and space vehicles including the Atlas B-3A, Atlas Saturn engine cluster, Navaho Engine and the Space Shuttle Main Engine.

Written history

1992 words

Source document Quoted word for word from HAER CA-2284. Not written, edited or summarised by this site.

The recording project is part of the Historic American Engineering Record (HAER), a long-range program to document historically significant engineering, industrial and maritime works in the United States. The HAER program is administered by the National Park Service, U.S. Department of the Interior. The Santa Susana Field Laboratory project was cosponsored by Marshall Space Flight Center with guidance and assistance by Ralph Allen, Joseph King, Melvin McKinstry, and Jennifer Groman from NASA Headquarters. The field word and measured and interpretive drawings were prepared under the general direction of Richard O Connor, Chief, Heritage Documentation Programs, National Park Service. The project was managed by Thomas Behrens, HAER Architect and Project Leader.

The measured and interpretive drawings were produced by John Wachtel, Jeremy Mauro, Ryan Pierce, Anne Kidd, Alex Matsov, and Daniel De Sousa. The large-format photographs were taken by Jet Lowe, HAER Photographer. The written historical and descriptive e data was produced by Robert Stewart. SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 3 Bravo Test Area The natural terrain of cliffs, slopes, and rocky outcroppings provided an ideal setting for the Bravo Test Area test stand complex. The landscape created a natural buffer zone for rocket engine fuel and deluge water, as well as blast and sound protection. The varying elevations allowed the observation bunkers to be placed at safe distances from the test stands, while providing an excellent visual advantage.

In addition, the water tanks and wells that fed Bravo were placed at higher altitudes than the test stands, allowing gravity to aid the water flow. The natural terrain also dictated the design of the manmade elements within the test complex site. The main road through the Bravo Test Area provides direct access to the First Deck of each test stand, as well as all contributing and noncontributing buildings and structures, except for the terminal house and the observation bunker. A small branch off the main road slopes down to the terminal house; the observation bunkers had wooden access stairs, which are no longer extant. Below this road level, roughly in line with the terminal house, are the stands flame deflectors.

Each test stand had a gunite channel, which directed run-off from the deflector to the earthen spillway. Each channel measures 50' long and 18' wide at the deflector, narrowing to a width of 10' where it meets the terrain. The channels are 4' deep with banked sides. The main road curves around the spillway area, and ends at the recording center. The Bravo test stands were the site of multiple static engine tests run between and These included experiments for Atlas ICBM thrust chambers in the and early Also in the developmental E-1 thrust chambers, F-1 thrust chambers, gas generators, heat exchangers, turbopumps, and components were evaluated. After Lunar Module Rocket Engine assemblies, Atlas and Delta vernier engines were tested.

In the and beyond, Atlas sustainer turbopumps, booster engines and Delta turbopumps underwent extensive runs. SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 4 The test stands, blockhouse, ancillary buildings and structures were also constructed by the Los Angeles architectural-engineering firm of Daniel, Mann, Johnson & Mendenhall, with consultant Walter Riedel, a German engineer and rocket engine expert who had worked with Dr. Wernher von Braun s team in Nazi Germany and had been assigned by to NAA in Los Angeles under Project Paperclip. Riedel s influence is apparent, as the Alfa site is representative of a static rocket engine test site of the late and early It echoes site planning and design principles modified from late World War II German installations.

Bravo Test Stand I Designed in the Bravo I Test Stand has overall dimensions of approximately 36' long, 36' wide and 46' tall, excluding the upper truss work. The entire test stand is built of structural steel and supported by concrete pile foundations at the four corners. The First Deck, considered to be ground level, measures 36' by and has a 24' by 24' opening in the center. The opening is covered with removable metal grating while stationary platforms are placed around the circumference. Approximately above the First Deck is the Second Deck. This level is slightly smaller, measuring roughly 30' by with a 14' by 14' opening in the center. Like the lower deck, permanent platforms surround the opening, which has removable platforms.

Historically, the fuel tanks would have been located on this level. A metal railing surrounds both decks. Above the second deck is a light metal truss system supporting the cranes and light fixtures. The north and south elevations take the form of upside-down trapezoids, while the east and west elevations are rectangular. On the north and south sides of the test stands are metal steps for access to the First and Second Decks. Additionally, there are steps to reach the intermediate platform level, which sits about 6' off the First Deck and projects over the east. This level is used for test firing in the horizontal position. Below the First Deck is the flame deflector.

The flame deflector measures approximately 16' in width, 30' in depth and 23' in height, overall, and has a separate foundation from the test stand. Across the interior surface of the deflector are numerous perforations for water to be injected onto the deflector surface during testing. This dissipates the heat and SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 5 prevents the steel from melting due to the heat produced by the engines. At the base of the deflector is a 50' long gunite run-off channel. The channel measures 18' wide at the deflector and narrows to a width of 10' where it meets the terrain. It is 4' deep with banked sides. To the northwest of the stand is a two-level instrumentation panel.

The upper level contains the valves for the systems, while the lower level has gauges that monitor the systems. To the north of this panel is the Electrical Control Shack. Bravo I was rated for testing engines producing relatively low thrust yields (rated in pounds) that characterized the rocket engines of The Los Angeles architectural-engineering firm of Daniel, Mann, Johnson & Mendenhall, with consultant Walter Riedel, designed the test stand. The base foundations of Bravo I are tied into the existing natural rock and reflect earlier construction techniques to a much greater extent than typically found after the early This replicates the design and engineering of similar test stands of in Nazi Germany. The design mitigated against explosions on the test stands.

The stand was over- engineered to accommodate the uprated rocket engines of the future. Bravo I has been modified during its operational period; these changes have reflected new technologies and the requirements for testing different engines. Bravo Test Stand II The original Bravo II Test Stand, designed in had approximate overall dimensions of 40' in length, 40' in width and 45' in height, excluding the fuel tanks. It was built of structural steel with reinforced-concrete footings and had a flame deflector that opened to the east. A 50'-long gunite channel directed the run-off to a small reservoir.

The upper half of Bravo II contained two metal decks, the First Deck (roughly 40' by and the Second Deck (roughly 30' x Each deck had an opening in the center for engine exhaust and/or fuel tank connections. Between these two decks was a mezzanine deck providing access to the engine s main compartments. Access stairs to the decks were on the north side of the stand. Above the Second Deck sat two vertical fuel tanks, one on top SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 6 of the other. A truss structure around the lower fuel tank supported a work platform. A second work platform sat at the top of the upper fuel tank and had support posts that projected from the tank. Bravo II was remodeled from to based on designs by Rocketdyne.

Much of the original stand was dismantled, including the flame deflector and its support mechanisms, the First Deck dolly and rails and the fuel vessels, as well as the stairs, handrails and ladders. The remainder of the original stand was incorporated into the new, larger stand. Bravo II currently measures approximately in length, 56' in width, and in height overall, inclusive of all components except for the crane. The base of the stand is composed of a steel truss support system to support the now stationary First Deck. The First Deck sits at ground level and measures roughly by It contains three separated test positions for various small engines and components. At the south end are stairs that lead to the base of the test stand.

About above this level is the Mezzanine, which measures approximately by Projecting from the west end of this deck is a 5-ton bridge crane. Placed across this level are the pressure transistor boxes and the electrical and mechanical valves. The Second Deck sits roughly above grade and measures about by This level holds four vertically set fuel tanks, in the middle of which is a support post for a crane. At the top of each fuel tank is an access platform, supported by steel brackets attached to the tank. The Mezzanine and Second Decks are set back from the eastern end of the First Deck approximately 9' and are accessed by metal stairs on the north elevation. The most distinct features of the Bravo II Test Stand are the three 24"-diameter Turbine Exhaust Pipes on the south elevation.

These pipes were part of the upgrades, and included one vent pipe, A, B, and C, for each test position. Test position A sits 24' north of the center point of the test stand; position B is 10' north and 27' east of the center; and position C is 10' south and 27' east of the center. The exhaust pipes stand roughly 6' high at each test position, through the First Deck and run along underneath to the south side. At the south elevation, they rise 76' where there is an access platform. From there, they angle 15 degrees to the east, and pipe A extends for an additional SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 7 pipe B for and pipe C for which allows the exhaust flames to be directed up and away from the test stand and fuel vessels.

By the late a fourth vent pipe was added to the test stand, located behind the original three. Additional features of the Bravo II Test Stand include the Electrical Control Shack to the northwest, a LOX and a vessel to the north and two kerosene tanks to the east, where the gunite channel once sat. The Bravo test stands were the site of multiple static engine tests run between and These programs included tests for developmental Atlas intercontinental ballistic missile engines, Navaho cruise missile engines, Thor and Jupiter intermediate range ballistic engines, Thor engines for space vehicle boosters, Atlas engines for space vehicle boosters, the uprated Thor, and engines for the Delta space vehicle.

Bravo II is associated with multiple static engine tests run between and including tests for the Atlas ICBM thrust chambers in the and early E-1 developmental thrust chambers were tested in the Thrust chambers for the gas generators and heat exchangers were also evaluated at this time. After turbopumps, and their components were tested. Operating characteristics of the Lunar Module Rocket Engine assemblies were documented in the late From the and beyond Atlas and Delta vernier engines were run. Atlas sustainer turbopumps and booster engines underwent development testing in the as well as Delta turbopumps.

Conforming to the Bravo I stand contracts, this test stand was designed by the Los Angeles architectural-engineering firm of Daniel, Mann, Johnson & Mendenhall, with consultant Walter Riedel. SANTA SUSANA FIELD LABORATORY, BRAVO TEST AREA HAER No. CA-2284 Page 8 Figure 1: Layout of Bravo Test Site and Stands

In context

Simi Valley, California The place record: every map, photograph and survey of this town.
Ventura County, California 247 topographic sheets across the county.
Library of Congress record The original filed report as the survey filed it.

Also surveyed in Simi Valley

19 records

The federal surveyors worked through Simi Valley building by building. These are the other structures they measured and filed a report on, longest report first.

SheetStructure SurveyReport
Grandma Prisbrey's Bottle VillageHALS CA-424,180 words
Santa Susana Field LaboratoryHAER CA-22853,913 words
Santa Susana Field LaboratoryHAER CA-22823,574 words
Santa Susana Field LaboratoryHAER CA-22832,465 words
Santa Susana Field LaboratoryHAER CA-2283-A49 words
Santa Susana Field LaboratoryHAER CA-2283-C49 words
Santa Susana Field LaboratoryHAER CA-2284-A49 words
Santa Susana Field LaboratoryHAER CA-2284-B49 words
Santa Susana Field LaboratoryHAER CA-2284-E49 words
Santa Susana Field LaboratoryHAER CA-2285-F49 words
Santa Susana Field LaboratoryHAER CA-228748 words
Santa Susana Field LaboratoryHAER CA-2285-B47 words
Santa Susana Field LaboratoryHAER CA-2285-C47 words
Santa Susana Field LaboratoryHAER CA-2285-D47 words
Santa Susana Field LaboratoryHAER CA-2285-E47 words
Santa Susana Field LaboratoryHAER CA-2283-B45 words
Santa Susana Field LaboratoryHAER CA-2284-C45 words
Santa Susana Field LaboratoryHAER CA-2285-A45 words
Santa Susana Field LaboratoryHAER CA-228644 words

Provenance

  • Written history. Quoted verbatim from HAER CA-2284. United States federal work, no copyright under 17 U.S.C. 105.
  • Text capture. Machine-read from the scanned typescript filed with the survey, so spelling and spacing follow the original page.
  • How this page is made. Documentary passages are quoted from the linked federal record; page labels and counts are clearly marked as site presentation or calculations.