BlockBefore

Weber Avenue Overcrossing, Weber Avenue above East Belmont Avenue, Fresno

Weber Avenue Overcrossing, Weber Avenue above East Belmont Avenue, Fresno, Fresno County, CA. Surveyed as HAER CA-2324, with a 2,653-word written history.

From the record

“The Weber Avenue Overcrossing is a pre-stressed concrete bridge designed by the California Division of Highways.”

Written record, HAER CA-2324 survey. Machine-read text.

Surveyed by the federal HAER program as HAER CA-2324 · the record runs 2653 words · one of 32 surveyed structures published for this county.

Sources: the survey record at the Library of Congress

Location

41 words

Source document Quoted word for word from HAER CA-2324. Not written, edited or summarised by this site.

N. Weber Avenue above E. Belmont Avenue, between N. Thorne Avenue and N. Farris Avenue, Fresno Fresno County, California USGS Quadrangle: Fresno North UTM Coordinates: Zone 11, mE, mN Present Owner/: City of Fresno Occupant Fresno Street, Fresno Fresno County, California

Significance

171 words

Source document Quoted word for word from HAER CA-2324. Not written, edited or summarised by this site.

The Weber Avenue Overcrossing is a pre-stressed concrete bridge designed by the California Division of Highways. Completed in the Weber Avenue Overcrossing was the second pre-stressed concrete bridge constructed in California. The first in the state was a pedestrian bridge built in over the Arroyo Seco Channel in Los Angeles. However, the Weber Avenue Overcrossing was the first such structure in California to support vehicular traffic.

Following an extensive research and evaluation process, the Weber Avenue Overcrossing is determined eligible for listing to the National Register of Historic Places at the state level under Criterion C as one of the pioneering examples of the use of pre-stressed concrete in California, and the first vehicular bridge in California to use this innovative construction technique. Historians: Madeline Bowen, MA and Patricia Ambacher, MA Historians AECOM L Street, Suite 400 Sacramento, CA Initial Draft: November Joel Levanetz, MA AICP RPA Senior Architectural Historian Chambers Group, Inc. Chesapeake Drive, Suite 202 San Diego, CA Revised Draft: May WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 2

Written history

2366 words

Source document Quoted word for word from HAER CA-2324. Not written, edited or summarised by this site.

The Level II Historic American Engineering Record (HAER) contained within this document was prepared for the California High Speed Rail Authority to record the property in partial fulfillment of mitigation measures outlined for Construction Package 1 of the project. The documentation was originally drafted in by AECOM. Madeline Bowen of AECOM served as principal investigator for the project. Patricia Ambacher of AECOM conducted primary research and assisted with document preparation. The original draft was then updated and revised by Joel Levanetz, a Senior Architectural Historian with Chambers Group, Inc., San Diego, California. The following HAER relies on documentation previously prepared for the undertaking.

All materials are properly cited to clearly indicate the source of the information. Stephen Schafer (Schaf Photo) created new contact prints from the negatives in February WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 3 Part I. Historical Information A. Physical History 1. Date of Construction: The property was originally constructed in by the California Division of Highways. 2. Engineers: Although the California Division of Highways is credited with implementation of the project, research failed to indicate a specific engineer or supervisor responsible for construction of the overcrossing. 3. Builder, Contractor, Suppliers: The historical record identified the builder as the Thomas Construction Company of Fresno, California. 4.

Original Plans: The original form and massing of the subject property is currently retained. An essential component of the property s original plan was the application of pre- stressed concreted to accommodate the heavier loads of vehicular traffic. As a result of its location, the original plans for the bridge had to address two specific constraints. This included an appropriate height for the structure to attain the required clearance under the bridge as well as an approach that would allow Belmont Avenue to remain operational during construction. Since cast-in-place concrete construction required closure of the Belmont Avenue corridor for the formwork, it was eliminated as an option. The next consideration was a steel girder bridge.

However, this was deemed too expensive and limited the overall clearance of the structure. Similarly, precast concrete girders were prohibitive due to the restrictive height limit they would create. As such, the original plans for the nearly 67 foot span required use of pre-stressed concrete. See Part II. Structural/Design Information for a detailed description of the features. 5. Alterations and Additions: According to the Department of Parks and Recreation 523 Forms from alterations appear to be limited to routine maintenance.1 B. Historical Context The Weber Avenue Overcrossing was constructed to carry southbound traffic on North Weber Avenue over old Highway 99 (North Golden State Boulevard) and East Belmont Avenue.

The overcrossing eliminated one portion of an existing three-phase traffic signal system. In Belmont Avenue carried vehicles every day. North Farris Avenue and North H Street end at East Belmont Avenue, and North Weber Avenue crossed East Belmont Avenue creating a five-point intersection that experienced a traffic volume of cars per day. It was dubbed 1 Hope, Andrew. California Department of Parks and Recreation 523 Forms for Weber Avenue Overcrossing. August WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 4 Fresno s worst bottleneck .2 The Weber Avenue Overcrossing is a prestressed-concrete bridge completed in by the California Division of Highways to alleviate this congestion.

As noted above, it represents the first prestessed-concrete bridge constructed in California to support vehicular traffic. During its early statehood, many of California s first bridges were constructed as toll roads by private individuals. In the California legislature enacted laws that allowed the counties to take control of road construction, and in the legislature mandated that county surveyors advise on bridge design and construction. This attracted trained and experienced engineers to these professional positions.

However, it was the development of the state highway system in the century that resulted in most of the bridge construction in California.3 While bridges found throughout the state vary in type, materials and methods of construction, common styles include metal truss and concrete bridges. Unlike on the East Coast, where steel mills provided a relatively inexpensive product that could be shipped easily, steel was expensive in early century California. However, high-quality cement was readily available throughout the West Coast.

Therefore, in California, constructing reinforced concrete bridges proved economically practical, and this type of bridge became one of the most prevalent types in the state.4 The concrete bridges of the early century typically fall into four categories: closed spandrel arch, open spandrel arch, concrete girder, and concrete slab. In highway construction, the concrete girder was the most popular, followed by the concrete slab bridge.5 Bridges constructed in the first half of the century were often built using reinforced concrete. In this technique, steel bars are embedded in concrete, forming a bond and increasing the tensile strength.6 This allows the concrete to withstand more weight and stress.

In bridge construction, the steel bars are placed in the lower section of the beam, which allows for the crossing of greater distances. The beam is progressively loaded until it reaches its tensile strength limit and begins to crack. The load is then transferred to the steel reinforcements, and the steel stretches as it bears its share of the load.7 This was the standard practice for the construction of bridges in the United States until the early when engineers began using the new technology of prestressed concrete. Pre-stressed concrete was first developed in Europe in the early century by Eugene Freyssinet, a French engineer.

In Europe, its use began to grow, particularly after World War II, when there was a shortage of steel and a high demand to rebuild bridges lost during the war.8 During the manufacture of prestressed concrete, the steel is placed in tension while the concrete is poured around it. When the concrete sets, the tension is released, which causes the 2 Bezouska, Thomas J. Precedent: First Pre-stressed Highway Bridge Planned for Fresno. California Highways and Public Works, September-October 3 Mikesell, Steven D. Historic Highway Bridges of California. Sacramento: California Department of Transportation, 4 Ibid. 5 Ibid. 6 Ibid. 7 Barton, Robert M. Prestressed Bridge: First of its Kind in State Is Built in Los Angeles. California Highway and Public Works, March-April 8 Dallaire, Gene.

The Birth and Growth of History s Most Exciting Building Material. Civil Engineering, October WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 5 steel to contract and causes a compression force in the concrete.9 Prestressing makes the concrete stronger and reduces cracks except under excessive loads. Fewer materials are necessary when using prestressed concrete because precast girders manufactured off-site can be used, and it is not necessary to build temporary timber frames.

Finally, unlike with most steel bridges, there is no need to paint bridges made of prestressed concrete.10 Among American engineers in the mid- century, there were generally five acceptable methods for prestressing concrete: using the seven-wire prestressing strand, plant pretensioning, using long- line steel casting beds, using high early strength concrete, and steam curing.

By there were more than 200 prestressing plants in the United States.11 In the United States, the first pre-stressed concrete bridge constructed was the Walnut Lane Bridge in Philadelphia in California introduced its first pre-stressed concrete bridge, a pedestrian bridge, in the Arroyo Seco Park near the city of South Pasadena the same year.12 By an estimated 100 projects were under construction using this new method, two-thirds of which were bridges.13 The Weber Avenue Overcrossing was the second bridge constructed in California using prestressed concrete, and the first to accommodate the heavier loads of vehicle traffic. Two issues specific to this location led to the choice of using prestressed concrete.

First among these issues was the need for a minimal depth of structure, so the Belmont Avenue would not need to be further recessed to get the required clearance under the bridge. The second consideration was the need to maintain traffic on Belmont Avenue during construction. Cast-in-place concrete construction was ruled out for this project since the necessary formwork would have required the closure of Belmont Avenue for an extended period. A steel girder bridge would have been more expensive than concrete and would have required a minimum superstructure depth of 46 inches. Precast concrete girders, without prestressing, were cheaper than steel but would have required an even deeper superstructure of 56 inches.

The technique that was ultimately chosen, using precast, prestressed concrete beams, proved to be the cheapest to build and had a depth of only 40 inches. In addition, the weight of the superstructure was reduced by pounds compared to regular concrete construction.14 The Weber Avenue Overcrossing demonstrated the efficiency, reliability, and cost-effectiveness of prestressed concrete, and marked the beginning of a new era in bridge engineering. The use of this technique grew rapidly in the following years, with 12 extant examples from and more than 20 each year in and and more than 70 each year in and The number of prestressed concrete bridges built in California continued to increase from 9 Hope, Andrew.

California Department of Parks and Recreation 523 Forms for Weber Avenue Overcrossing. August 10 Barton, Robert M. Prestressed Bridge: First of its Kind in State Is Built in Los Angeles. California Highway and Public Works, March-April 11 Precast/Prestressed Concrete Institute. Building Code Provisions for Precast/Prestressed Concrete: A Brief History. PCI Journal, 12 Barton, Robert M. Prestressed Bridge: First of its Kind in State Is Built in Los Angeles. California Highway and Public Works, March-April 13 Holley, Myle. Prestressed Concrete Makes Rapid Progress in the United States. Civil Engineering, June pp. 14 Bezouska, Thomas J. Precedent: First Pre-stressed Highway Bridge Planned for Fresno. California Highways and Public Works, September-October WEBER AVENUE OVERCROSSING HAER No.

CA-2324 PAGE 6 on, to a high of approximately 300 examples built in By 78% of the bridges constructed in California were made of prestressed concrete.15 Age, increased traffic, and increased vehicle weights have necessitated maintenance and rehabilitation of many of these bridges. Prestressed concrete, however, continues to be a popular, cost-effective, and durable method for bridge construction. The use of prestressing is now a standard part of modern infrastructure development with more than prestressed concrete roadway bridges currently in California. 15 Dallaire, Gene. The Birth and Growth of History s Most Exciting Building Material. Civil Engineering, October WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 7 Part II. STRUCTURAL/DESIGN INFORMATION A. General Statement 1.

Character: As one of the first examples of a prestressed-concrete vehicle bridges in California, the Weber Avenue Overcrossing is significant for its method of construction. The bridge s superstructure is composed of precast, prestressed, concrete T-beams. These elements most notably convey the significance of the bridge design. Refer to Section B. Physical Description below for detailed information on the T-beams. 2. Condition of fabric: Aside from minor cracking and spalling, the Weber Avenue Overcrossing appears to be in good condition. B. Description 1. Materials: The Weber Avenue Overcrossing is a single-span bridge that carries southbound vehicular traffic on North Weber Avenue over the Belmont Avenue Subway below.

The materials used in the creation of the bridge are almost exclusively concrete and asphalt at the roadway. The exceptions to this include minor, non-historic period metal components such as conduit installed along the west wall of the span and an overhead streetlight near the southern perimeter of the subject property. 2. Dimensions: The Weber Avenue Overcrossing is 66 feet, nine inches in length and 28 feet in width, including a six-foot-wide pedestrian walkway extending along the east side of the span. The superstructure is comprised of ten precast, prestressed concrete T- beans set on abutments. The T-beams are 36 inches high, 36 inches wide at the top, and 16 inches wide at the bottom, with six-inch thick vertical webs. 3.

Layout: The bridge crosses East Belmont Avenue at an approximately 41 degree angle. The bridge abutments are integrated into the Belmont Avenue Subway retaining walls, constructed in The street-side portion of the Weber Avenue Overcrossing is enclosed at the east and west by low concrete railings decorated with arched openings.16 Located adjacent to the west of the subject property is the Belmont Avenue Bridge (Bridge No. The Belmont Avenue Bridge is a reinforced concrete and steel-girder railroad bridge with a span of 42 feet that carries trains over Belmont Avenue below. Below the two bridges is the Belmont Avenue Subway. Further west is the Belmont Avenue Traffic Circle. 16 Hope, Andrew. California Department of Parks and Recreation 523 Forms for Weber Avenue Overcrossing.

August WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 8 C. Site Information The Weber Avenue Overcrossing is situated in an area of Fresno that represents the boundary between several distinctive land uses. To the north and south of the subject property are residential neighborhoods characterized by detached, single-family homes. Northwest of the resource is Roeding Park. This property includes a zoo and various other recreational facilities. Southwest of the overcrossing is a water collection basin under the authority of the Fresno Metropolitan Flood Control District. Parcels located further south and southeast of the overcrossing support heavy commercial and industrial uses. WEBER AVENUE OVERCROSSING HAER No. CA-2324 PAGE 9 Part III. Sources of Information A.

Primary Sources As-built plans, (Housed at Caltrans bridge record archives). Barton, Robert M. Prestressed Bridge: First of its Kind in State Is Built in Los Angeles. California Highway and Public Works, March-April Bezouska, Thomas J. Precedent: First Pre-stressed Highway Bridge Planned for Fresno. California Highways and Public Works, September-October Bids for Prestressed Bridge Opened. California Highways and Public Works, November December Bridge Report, July 28, (Housed at Caltrans bridge record archives). Precast/Prestressed Concrete Institute. Building Code Provisions for Precast/Prestressed Concrete: A Brief History. PCI Journal, B. Secondary Sources Dallaire, Gene. The Birth and Growth of History s Most Exciting Building Material. Civil Engineering, October Holley, Myle.

Prestressed Concrete Makes Rapid Progress in the United States. Civil Engineering, June Hope, Andrew. California Department of Parks and Recreation 523 Forms for Weber Avenue Overcrossing. August Mikesell, Steven D. Historic Highway Bridges of California. Sacramento: California Department of Transportation, C. Likely Sources Not Yet Investigated Other repositories that may contain historical background information relevant to the Weber Avenue Overcrossing include the following: Caltrans District 6 archives, which may contain historic photographs and additional historic drawings; and the Fresno Historical Society.

In context

Fresno, California The place record: every map, photograph and survey of this town.
Fresno County, California 484 topographic sheets across the county.
Library of Congress record The original filed report as the survey filed it.

Also surveyed in Fresno

14 records

The federal surveyors worked through Fresno building by building. These are the other structures they measured and filed a report on, longest report first.

SheetStructure SurveyReport
Fulton MallHALS CA-11610,914 words
Roeding ParkHALS CA-597,634 words
Ivan Carter McIndoo HouseHABS CA-28856,822 words
John G. Porter HouseHABS CA-28846,711 words
Matthew McIndoo HouseHABS CA-28766,575 words
Albert G. Wishon HouseHABS CA-28836,210 words
Charles H. Cobb HouseHABS CA-28775,371 words
Newman J. Levinson HouseHABS CA-29055,029 words
Lamb TownhouseHABS CA-28744,457 words
Ira H. Brooks HouseHABS CAL,10-FRES,1-4,276 words
Burnett Nurse's HomeHABS CAL,10-FRES,2-3,672 words
Belmont Avenue SubwayHAER CA-23253,412 words
O'Brien HouseHABS CA-28823,326 words
George H. Larsen HouseHABS CA-28753,087 words

Provenance

  • Written history. Quoted verbatim from HAER CA-2324. United States federal work, no copyright under 17 U.S.C. 105.
  • Text capture. Machine-read from the scanned typescript filed with the survey, so spelling and spacing follow the original page.
  • How this page is made. Documentary passages are quoted from the linked federal record; page labels and counts are clearly marked as site presentation or calculations.