The Walker Bridge is a steel Pennsylvania Petit truss, built in in Folsom, Sacramento County, California and moved to this site by the California Division of Highways (predecessor to Caltrans) in The bridge was determined eligible for listing in the National Register under Criteria C (as a very rare and distinguished example of a particular bridge type) and A (for its role as a transportation link at the Klamath River crossing). The appropriate period of significance for the bridge extends from (when it was built) to (when it began serving at the current location). Report Prepared by: Stephen D. Mikesell JRP Historical Consulting Services Drew Avenue, Suite 105 Davis, California Date: April 23, WALKER BRIDGE (Klamath Bridge No. HAER No.
CA-184 (Page #2) Description: The Walker Bridge is a steel Pennsylvania Petit truss bridge. As noted, the structure was originally erected in Folsom in at a location several hundred miles southeast of the current site. The bridge was disassembled and re-erected at this site in The truss itself the metal shell for the bridge includes a very high percentage of its original materials. Maintenance records indicate that incidental pieces of the bridge were replaced at the time of the relocation, including the bearings at the abutments. No doubt some "pins" (large connecting bolts) were replaced at the same time on an as-needed basis.
The bulk of the truss, however, is original, including the top and bottom chords, compression members, and substruts, which comprise the essence of the Pennsylvania Petit design. The integrity of the structure is very good for the truss itself, the principal basis for National Register eligibility, but poor in terms of integrity of location and setting because the bridge has been moved. At the Walker site, the crossing is wider than its original site at Folsom, requiring higher abutments and piers due to flooding dangers. As constructed at the Walker site in the truss span rests on piers, with timber stringer approach spans at either side. The bridge includes a 20' approach on the north side and five spans of approximately 20' each on the south.
The truss span was stripped of its floor system in Folsom; the contract called for the construction of a new timber deck. The bridge has undergone major modifications since its erection at the Klamath River site in all such modifications relating to its deck and approaches. The approaches and deck were completely rebuilt in At that time, the timber deck (a feature) was demolished and rebuilt to a single-lane capacity. The single-lane configuration resulted in an awkward appearance in which the 12' wide deck is only about two-thirds as wide as the metal truss, designed to accommodate an 18' deck. At the same time, the timber approach spans to the south were demolished and replaced with a raised berm.
Integrity for the bridge as a whole is fair, balancing the good integrity for the truss and poor integrity for other elements of the structure. Historical Context: The Walker Bridge was built in by Sacramento County to carry traffic across the American River near downtown Folsom on what is now Greenback Lane. The bridge was fabricated by the San Francisco Bridge Company, a pioneering metal truss fabricator in century California. It is a very rare example of the work of this important early bridge manufacturer. The steel bridge was essentially bypassed in when the county built a concrete arch bridge downstream from it. The concrete arch, locally known as the "Rainbow Bridge," still stands and it too has been determined eligible for listing in the National Register.
Although bypassed, the steel bridge remained on its original abutments until WALKER BRIDGE (Klamath Bridge No. HAER No. CA-184 (Page #3) The Division of Highways needed the bridge to serve as a temporary state highway structure pending reconstruction of Highway 96. Until the early the forerunner of Highway 96 (the "Pacific Highway") crossed the Klamath River near the Walker Bridge crossing site, continuing west (downstream) on the south side of the river. The highway bridge at that crossing was a single-lane suspension bridge, installed by the county. That bridge was posted at five tons and was beginning to fail by The state needed to replace it but was reluctant to spend a great deal on a bridge that would soon be bypassed.
As stated by Division of Highways bridge engineer, James Gallagher, "It was therefore imperative that a new bridge be built and at the same time desirable to invest as little money as possible in the new structure since it would only serve State Highway traffic till such time as the new highway is completed." The state Bridge Department, headquartered in Sacramento, learned of the steel bridge in nearby Folsom, which happened to be about the length needed in the Klamath River crossing at Walker Road. The department inspected the bridge, found it serviceable, and let a contract for it to be dismantled and shipped to Siskiyou County. The contract was let to the Gutleben Brothers.
The contractor built a timber truss scaffolding on timber bents which allowed it to disconnect the bridge from its abutments and dismantle it piece-by-piece. At its Folsom site, the bridge included no approaches, i.e., the single truss span rested directly upon the abutments, with no intermediate piers or shorter approach spans. At the Walker site, however, the crossing was wider and required higher abutments and piers due to flooding dangers, requiring that the truss span rest on piers, with timber stringer approach spans at either side. As constructed in the bridge included a 20' approach on the north side and five spans of approximately 20' each on the south.
In addition, the truss span had been stripped of its floor system in Folsom; the contract called for the construction of a new timber deck. The bridge has undergone major modifications since its erection at the Klamath River site in all such modifications relating to its deck and approaches. The approaches and deck were completely rebuilt in At that time, the timber deck (a feature) was demolished and rebuilt to a single-lane capacity. The single-lane configuration resulted in an awkward appearance in which the 12' wide deck is only about two-thirds as wide as the metal truss, designed to accommodate an 18' deck. At the same time, the timber approach spans to the south were demolished and replaced with a raised berm.
Shortly after that work was accomplished, the bridge was relinquished from state ownership to Siskiyou County. Additional deck work was accomplished in to lighten the dead load. WALKER BRIDGE (Klamath Bridge No. HAERNo. CA-184 (Page #4) The Walker Bridge is located in an isolated part of Siskiyou County, very near the Oregon border. It is immediately adjacent to Highway 96, several miles west of the small community of Klamath River. At the north bank, the bridge nearly abuts Highway 96 with only a short roadway separating the two. On the south bank of the river, Walker Bridge Road passes through a large alfalfa field, one of the few arable field anywhere along the Klamath.
As discussed, the 3 30' Walker Bridge truss span is the primary reason the bridge was determined eligible for listing in the National Register of Historic Places. The truss is a Pennsylvania Petit through truss. All-metal truss bridge design developed quickly in the late century, with bridge engineers and manufacturers devising more and more varieties of truss systems to handle different circumstances. All-metal trusses initially were adapted from the two most popular wooden truss forms, the Pratt and Warren trusses. The Pennsylvania Petit is a Pratt derivative. The Pratt truss, first developed in was the most common all-metal truss type, used in thousands of crossings which required individual spans of or less.
It included a horizontal top chord, vertical compression members and small diagonals. Many other well-known truss designs, developed to handle longer spans, were essentially variations on the Pratt. The Parker truss, for example, was simply a Pratt truss with a polygonal top chord. Parker trusses were built in great numbers in California and elsewhere. The Pennsylvania Petit design was in turn a variation on the Parker truss. Like the Parker, it had a polygonal top chord. It was different from the Parker, however, in that it included a scries of sub-struts and sub-ties. The Pennsylvania Petit truss was specifically designed for longer crossings, spans which were too great for the basic Pratt or even the more versatile Parker design.
A similar truss type is the Baltimore Petit, which is nearly identical to the Pennsylvania Petit except that the top chord is straight and parallel to the bottom chord. The Pennsylvania Petit was never built in great numbers and is now a very rare bridge type in California and elsewhere in the United States. In the mid-1980s (when field work was conducted for the Caltrans Historic Bridge Inventory), there were six Pennsylvania Petit truss bridges still standing in the state, including the Walker Bridge. Of these, the Walker Bridge had the distinction of being the oldest as well as the largest. WALKER BRIDGE (Klamath Bridge No. HAER No. CA-184 (Page #5)