HISTORICAL INFORMATION FOR THE CHINA LAKE PILOT PLANT HISTORIC DISTRICT A. General History of China Lake Pilot Plant This report describes the general character of the China Lake Pilot Plant and the history of its development, both in terms of its physical history and historical context. Please refer to HABS reports CA-2774-A to CA-2774-D for information on specific buildings addressed by this report. The China Lake Pilot Plant is significant for its role in development of the Navy rocket program during World War II and during the early years of the Cold War. The role differed greatly, before and after V-J day in the late summer of During World War II, the China Lake Pilot Plant was as much a factory as it was an experimental production facility.
Throughout World War II, California Institute of Technology (CalTech) scientists were employed to develop rockets with two objectives in mind: to deliver weapons to the fleet for use during the war, and to develop technologies that would be available for deterrence after the war was concluded. The plant was built around the 12" and 18" presses (the measurement refers to the exterior diameter of the press, not to the size of the grain). These presses were designed specifically to extrude grains for use in motors for rockets that had some potential for use during the war. These buildings for the presses were built with a very specific purpose in mind. What was then known as Building 1 housed a 12" press.
It was designed specifically to extrude the 5" propellant "grain" that would be used for the HVAR, or Holy Moses rocket, which was under development and testing elsewhere at China Lake. Building 51 housed an 18" Press. It was similar in function to Building 1, but was designed to extrude grains that were in diameter, for use in the much larger Tiny Tim rocket, also under development at NOTS during World War II. The HVAR (Holy Moses) and Tiny Tim were used by American Navy pilots during World War II. Holy Moses was first used in Europe in the summer of following D- Day. of the rockets were delivered, most of them used in air-to-surface attacks against German tanks, in support of General George Patton's tank columns in France.
1 The US Army Air Corps fired the first group of these Navy rockets. The HVAR was also used extensively by Navy pilots in the Pacific Theatre beginning in December 1 Gerard-Gough and Christman, The Grand Experiment at lnyokern, Naval Ordnance Test Station Inyokern, China Lake Pilot Plant (Naval Air Weapons Station, China Lake Pilot Plant) HABS No. CA-2774 (Page 3) These rockets were used chiefly against Japanese transport ships and against island fortifications. The Holy Moses was also used by Navy pilots in the Pacific. Tiny Tim, the largest rocket available to American forces during World War II, was used sparingly in the late stages of the war. Tiny Tims were fired from Navy aircraft during the invasion of Okinawa.
2 The China Lake Pilot Plant produced a large part of the propellant used in the aforementioned rockets that were launched during the war. The exact proportion of such propellant produced at China Lake has not been determined. It is known that massive amounts of ballistite was pressed and machined at China Lake, all to the specifications for these rockets. It is estimated that several hundred thousand rocket motors were produced at the plant during the last year of World War II, accounting no doubt for a substantial proportion of the total American production capacity for these rocket motors. 3 After V-J Day, the China Lake Pilot Plant (and NOTS generally) gradually underwent a transition to peacetime activities.
In many respects, the immediate post-war period was the busiest time of all for NOTS. The Navy pursued completion of the facility and completion of development and testing of rockets that were nearing completion at the conclusion of hostilities. The China Lake Pilot Plant was removed from production as part of this active period just after World War II. The activities included large-scale production of the specific motors for the immediate post-war rockets developed at NOTS. It also included experiments on the production of different rocket motor systems. In time, however, the production capacity of the plant was scaled back considerably as major private manufacturers, such as the Aerojet Corporation, developed the capacity for rocket motor production that had been missing during the war.
By the large production capacity of the plant far exceeded the demand or need of the base. This became especially true after when the Atomic Energy Commission abandoned the nearby Salt Wells Pilot Plant, which had been built in to produce and test processes for producing the non-nuclear lenses used in manufacturing atomic bombs. When the AEC left Salt Wells, the Navy and NOTS suddenly possessed almost twice the capacity for producing and testing propellants. After the entire China Lake and Salt Wells area were incorporated into a unified operation used for testing both explosive and propellants, but not for the manufacture of either.
Both areas are still used to some degree, but many of the buildings in both areas are essentially "mothballed." Among the inactive buildings is the 12" Press Building and many of the processing buildings in the 2 Gerard-Gough and Christman, The Grand Experiment at lnyokem, 3 Geran:l'-Gough and Christman, The Grand Experiment at lnyokern, Naval Ordnance Test Station Inyokern, China Lake Pilot Plant (Naval Air Weapons Station, China Lake Pilot Plant) HABS No. CA-2774 (Page 4) area. In addition, NOTS in re-oriented the operation at the China Lake Pilot Plant, abandoning work on the original 5" and grains. The combined facility was selected to conduct experimental work on the production of new propulsion systems, included double-base propellants and liquid-fuel rocket motors. B.
Construction of China Lake Pilot Plant Throughout World War II, CalTech was under contract with the Federal government to conduct research and development, as well as testing and evaluation, on all aspects of rockets for use by the Navy, particularly Navy aviation. As part of its broad program of research on rockets, CalTech in began to test methods to produce ballistite, the chief material used in solid rocket propellant. This work was initially conducted in Eaton Canyon, just outside of Pasadena. 4 The Eaton Canyon facility was designed to be a "pilot plant,'' to test manufacturing techniques that could be safely and efficiently adapted by private companies.
The presumption was that private firms would ultimately manufacture propellant, as was the case with nearly all other aspects of Navy ordnance. The major propellant manufacturers, however, were slow to respond to the Navy's demands. A few specialized manufacturers did develop during the war, including the Aerojet Corporation, located in Rancho Cordova, which was founded in by CalTech personnel. 5 Nonetheless, the Navy's demand for propellant, for testing purposes and for battlefield use, was so great that the Eaton Canyon plant was drafted into a role as a major propellant manufacturer. Between and the facility produced five million pounds of ballistite.
6 The fact that such volumes of highly-explosive material were being manufactured, stored, and transported at the edge of a major metropolitan area was, a matter of concern to all parties, including CalTech and the Navy. The decision by the Navy to establish Naval Ordnance Test Station (NOTS) at Inyokern allowed the Navy and CalTech to abandon use of Eaton Canyon for this purpose. 4 "History of China Lake Pilot Plant from January I, to July I 5, no author, no date, typescript in Technical Library, China Lake NA WS, 5 Aerojet Magazine, La Jolla: Corporate Office of Public Affairs, Aerojet General Aerojet Summer I 992 at the Technical Library, China Lake NA WS. This is a special historical issue of the magazine.
6 NAWS China Lake, "East of Eaton: The Story of the China Lake Propulsion Laboratories," script for videotape, This text was provided by Leroy Doig, base historian at NA WS China Lake. Naval Ordnance Test Station Inyokern, China Lake Pilot Plant (Naval Air Weapons Station, China Lake Pilot Plant) HABS No. CA-2774 (Page 5) The Naval Ordnance Test Station (NOTS), as the name implies, was established chiefly for the purpose of testing Naval ordnance, particularly rockets: Its isolated locale was selected to facilitate this early function. The decision to make NOTS into a permanent facility, however, gave the Navy the opportunity to include buildings that could be used in all aspects of rocket research, development/testing and evaluation.
Michelson Laboratory, for example, was contracted to facilitate needed research and development. Similarly, the large expanses at China Lake allowed for inclusion of a new site for the propulsion pilot plant. The China Lake Pilot Plant was something of an afterthought in the overall site planning for NOTS and was not designed under the master architect-engineer contract with Stafford, Davies, and Gogerty, designers of most of NOTS. Rather, the design work for this facility was handled under a separate A&E contract between CalTech and its consulting engineer, Oliver G. Bowen and the CalTech architect, Palmer Sabin. The Navy was represented directly by the engineering firm of Holmes and Narver. 7 Excluding the administrative buildings (see HABS Nos.
2774-A through CA-2774-D), all buildings at can be understood only with reference to their original functions. In a detailed history of the construction of this plant, a NOTS historian explained how the plant layout and building designs were developed. 8 The entire process was governed by a committee with representatives from the affected agencies or groups: the Bureau of Ordnance, which had strict safety regulations regarding ordnance processing facilities; CalTech, which would operate the facility; NOTS, which had ultimate control over the unit; and the consulting engineer, who had to design the plant.
CalTech had requested a plant that was in easy walking distance for its workers, and preferred a location in what is now the golf course at the site, adjacent to the officers' housing area. In when the building plans were about 50% complete and construction had commenced the Bureau of Ordnance halted the work, insisting that the plant be built miles away from any residences. The difference of opinions between the Bureau of Ordnance and Cal Tech had to do with disagreement about the explosive "class" of ballistite. The Bureau regarded it a more dangerous material and specified a much larger buffer between the plant and the hundreds of residences at NOTS.
The Bureau's classification of the ballistite and their plant location specifications were adapted and the facility was moved over 4 miles away. The relocation of the facility allowed the construction of larger buildings, greater safety features, and general enlargement of the operations. This, however, required abandoning all of the plans previously developed by Bowen. 7 "History of China Lake Pilot Plant," 8 "History of China Lake Pilot Plant," Naval Ordnance Test Station Inyokem, China Lake Pilot Plant (Naval Air Weapons Station, China Lake Pilot Plant) HABS No. CA-2774 (Page 6) Not wanting to repeat the earlier error, subsequent planning involved even closer cooperation between the Navy and CalTech. The planning for relocated project was governed from the outset by CalTech, with Dr.
Bruce H. Sage taking the lead. Funding for construction came, not from Navy appropriations, but from a contract between CalTech and the Office of Scientific Research and Development. 9 Oliver G. Bowen, under contract to CalTech, prepared the over-all plan and did much of the design of the complex. He was assisted by architect Palmer Sabin, also under contract to CalTech, who was involved primarily with the administrative area. Safety considerations and topography largely defined the layout of the facility (the new site was on an alluvial fan at the base of Lone Butte). The NOTS historian wrote: The new site plan was laid out in a semi-circular plan to better fit the topography.
The increased intra-plant spacing of buildings; the increased distance between press line areas and motor loading groups; the isolation of the Service Group and the Static Firing Group, have resulted in materially increased costs for roads and utilities. 10 The buildings at the complex were arranged into six groups based on function. Two principal production groups were known as the 12" press group and the 18" press group and in each case, the group included a large press building and dozens of small buildings for processing the propellant extruded from the press. The ancillary buildings were identified by function - sorting and blending, flaking, annealing, inhibiting, inspecting, curing, boxing, loading, and so forth. These two production groups account for the bulk of buildings.
Smaller groups of buildings were laid out for motor loading, static firing, and for a small "experimental line." The administrative area, separated from the others, was called the service group, which included the office building, firehouse, changing room, gate house, Marine barracks, lunch room, laundry, and assorted other shops, warehouses, and service buildings. The design of the buildings is attributed to Oliver G. Bowen who, as noted, was under contract with Cal Tech for design of buildings associated with the university's work in the Navy's rocket program. Minutes from meetings indicate that Palmer Sabin was also involved in this design work. Palmer Sabin was a private architect who worked in Pasadena. Credited chiefly with the design of residential buildings, Sabin was under 9 J. D.
Gerard-Gough and Albert B. Christman, History of the Naval Weapons Center, Vol. 2, The Grcind Experiment at Inyokern, Washington Naval History Division. 10 Gerard-Gough and Christman, The Grand Experiment at lnyokern, 5. Naval Ordnance Test Station Inyokem, China Lake Pilot Plant (Naval Air Weapons Station, China Lake Pilot Plant) HABS No. CA-2774 (Page 7) contract with CalTech throughout its work with the Navy during World War II. It is likely that Sabin was most heavily involved in developing the architectural theme or program for the administrative complex. The bulk of the buildings at the China Lake Pilot Plant, however, were engineered rather than designed. It would be a mistake, however, to attribute this design work to any one individual.
Published histories of the construction of the plant emphasize the degree to which CalTech scientists controlled the design process for this plant. In the production area, the buildings simply took the form that was required to accomplish this task. These buildings were sturdy reinforced concrete shells cast in place around the equipment inside. The buildings literally take the form of the machinery, except that the thick concrete walls give an exaggerated sculptural quality to the enclosures. The architects of record - the firm of Holmes & Narver and architect Palmer Sabin - were reasonably well-known designers in the Pasadena area, although there is no indication that either had attempted to design any structures before the war that approximated those found at the China Lake Pilot Plant.
In fairness to Bowen and Sabin, however, no architect or engineer in the world had undertaken a project of this sort; the assignment was unique.