BlockBefore

Taluga, Suisun Bay Reserve Fleet, Benicia

Taluga, Suisun Bay Reserve Fleet, Benicia, Solano County, CA. Surveyed as HAER CA-336, with a 4,106-word written history.

From the record

“The Taluga is significant as an example of the T3-type tankers, which were developed with steam propulsion rather than turbo-electric drives.”

Written record, HAER CA-336 survey. Machine-read text.

Surveyed by the federal HAER program as HAER CA-336 · the record runs 4106 words · one of 191 surveyed structures published for this county.

Sources: the survey record at the Library of Congress

Location

95 words

Source document Quoted word for word from HAER CA-336. Not written, edited or summarised by this site.

Suisun Bay Reserve Fleet, Benicia vicinity, Solano County, California Type of Craft: T3-S2-A1/Auxiliary Trade: Fleet oiler Class: Ashtabula Principal Dimensions: Length (oa): Beam (molded): 75' Draft: Displacement: long tons Deadweight: long tons Gross registered tonnage: tons Maximum continuous shaft horsepower: Service speed: knots (The listed dimensions are as built, but it should be noted that draft, displacement, and tonnages were subject to alteration over time as well as variations in measurement.) Dates of Construction: Keel laying: 23 December Launching: 10 July Commissioning: 25 August Designer: U.S. Maritime Commission Builder: Bethlehem Steel Company, Sparrows Point, Maryland

Significance

63 words

Source document Quoted word for word from HAER CA-336. Not written, edited or summarised by this site.

The Taluga is significant as an example of the T3-type tankers, which were developed with steam propulsion rather than turbo-electric drives. The ship is also significant as the first civilian-crewed oiler in the Military Sealift Command. The crew of this ship, known as the Taluga Tigers, set the standard for all civilian-manned naval auxiliaries to the present. Taluga HAER No. CA-336 Page 2

Written history

3877 words

The headings the report itself prints. Each one jumps to where it begins.

Source document Quoted word for word from HAER CA-336. Not written, edited or summarised by this site.

This project is part of the Historic American Engineering Record (HAER), a long-range program to document historically significant engineering and industrial works in the United States. The Heritage Documentation Programs of the National Park Service, U.S. Department of the Interior, administers the HAER program. The project was prepared under the direction of Todd Croteau (HAER Maritime Program Coordinator). Crystal Olin, (HAER Intern), generated the drawings. Jet Lowe (HAER Photographer) produced the large-format photographs. Special thanks to Erhard Koehler (U.S. Maritime Administration), whose help and assistance greatly benefited the project. Taluga HAER No.

CA-336 Page 3 BACKGROUND One of the first priorities of the United States upon entering World War II was the construction of ships. The global experience and ferocity of World War I taught the United States that World War II would be on a grander scale, in more places, involve more people, and require more equipment total war.1 During World War II, the U.S. Maritime Commission became a pivotal force in the development and construction of ships, much like the U.S. Shipping Board had been in World War I. Created in the Maritime Commission succeeded the Shipping Board, but it generally followed the same directive: the promotion of U.S. shipping interests.

After the United States entered World War II, the Maritime Commission established the Emergency Program, a massive ship construction plan that utilized new and existing shipyards across the United States.2 The need for the Emergency Program stemmed from the decline of the maritime industry in the inter-war years. Most of the ships in the Merchant Marine originated from the mobilization endeavor authorized by the U.S. Shipping Board to support American troops in World War I. The board had approved the construction of 470 ships to support the war effort. Between and however, the board added ships to the Merchant Marine, giving the United States a more robust presence in international shipping than it had had in seventy years. The U.S.

stock market crash in and the Great Depression were major setbacks to the maritime industry. Many steamship companies were unable to replace or update aging ships over 90 percent of the fleet was over twenty years old and had an average speed of between 10 and 11 knots.3 In the mid-1930s, the U.S. government intervened with new legislation to aid the beleaguered maritime industry. President Franklin D. Roosevelt s New Deal economic policies eventually helped revive the Merchant Marine when Congress passed the Merchant Marine Act of The act created the U.S. Maritime Commission, superseding the U.S. Shipping Board, and it infused new capital and ideas for rebuilding the fleet. In the U.S.

Maritime Commission developed a long-range program for building 500 ships that were both contemporary and economical over a ten-year period. In the Maritime Commission determined that the production quota of fifty ships per year was too low and doubled it.4 There were mounting concerns about the war in Europe and the success of the German U-boat campaign against English shipping, particularly since U.S. steamship companies traded with England and France. The U.S. also feared that Germany might next turn its attention to U.S. ships or U.S. trade routes. 1 Russell F. Weigley, The American Way of War: A History of United States Military Strategy and Policy (New York, NY: MacMillan Publishing Co., Inc., pp. xxi-xxiii. 2 Ren De La Pedraja, A Historical Dictionary of the U.S.

Merchant Marine and Shipping Industry since the Introduction of Steam (Westport, CT: Greenwood Press, pp. The Maritime Commission issued contracts for vessels during World War II. Private firms built an additional 111 ships while foreign firms built sixty-five for a total of 3 Brian J. Cudahy, Box Boats: How Container Ships Changed the World (New York, NY: Fordham University Press, pp. L.A. Sawyer and Mitchell, Victory Ships and Tankers: The History of the Victory Type Cargo Ships and of the Tankers Built in the United States of America during World War II (Cambridge, MD: Cornell Maritime Press, Inc., p. 15. 4 Cudahy, Box Boats, p. 3; Sawyer and Mitchell, Victory Ships and Tankers, p. 15. Taluga HAER No.

CA-336 Page 4 In response, the Maritime Commission raised its shipping quota once again in August to 200 ships per year.5

Fleet Oilers

Shortly after the signing of the Merchant Marine Act in U.S. oil companies became interested in constructing high-speed tankers, as did the U.S. Navy. Commissioner Emory S. Land, chairman of the U.S. Maritime Commission, proposed that the commission subsidize the construction of these vessels by paying for upgraded engines. On 3 January the Maritime Commission signed a contract with the Standard Oil Company of New Jersey to subsidize twelve oilers, designated T3-S2-A1. That same day, Standard commissioned four shipyards, including Sun, Federal, Bethlehem-Sparrows Point, and Newport News, to each construct three tankers.6 These new fleet oilers were similar to an earlier design used when Land was Chief of the Bureau of Construction and Repair with the U.S. Navy.

The bureau s Central Drafting Office had developed lines for a fleet oiler in that corresponded to those of the oilers being built two years later. Although the naval architect for Sun Shipbuilding, E.L. Stewart, is credited with laying out the design and specifications, the final lines appear to be a combination of those from Sun s engineering staff and the Maritime Commission s technical team since there is a clear difference between the final version and the early designs of the U.S. Navy for a twin-screw fleet oiler.7 The USS Cimarron, the first in its class of was launched on 7 January and entered naval service as a fleet oiler. This was the navy s first fleet oiler since the Kanawha, dating to and had the distinction of being one of the largest and fastest to date.

The addition of T3s to the navy s fleet coincided with the success of U.S. Navy operations in the Pacific. During this time, the navy shifted its campaign from an offensive-defensive posture to a more open offensive drive. The acquisition of the T3-S2-A1s corresponded to the needs of the navy. As military operations increased in the Pacific in the navy required more oilers to continue operations. The second round of T3-S2-A1s to be built was the Ashtabula class, comprised of eighteen ships, including the Taluga. Bethlehem Steel in Sparrows Point, Maryland, constructed the entire class from to CONSTRUCTION Bethlehem Steel in Sparrows Point, Maryland, laid the keel of the Taluga (AO-62) under a Maritime Commission contract (Hull No.

on 23 December Bethlehem Steel was an established firm in steel manufacturing, ship building, and ship repairing. The Maryland Steel Company originally built the Sparrows Point Shipyard in and delivered its first ship in 5 Sawyer and Mitchell, Victory Ships and Tankers, p. 16; Thomas Wildenberg, The Origins and Development of the T2 Tanker, American Neptune (Summer pp. 6 Wildenberg, Origins and Development, pp. 7 Wildenberg, Origins and Development, pp. 8 Sawyer and Mitchell, Victory Ships and Tankers, p. James L. George, History of Warships: From Ancient Times to the Twenty-First Century (Annapolis, MD: Naval Institute Press, p. Taluga HAER No.

CA-336 Page 5 In Bethlehem Steel purchased the shipyard, which by that point had produced 176 ships, almost all of which were commercial, aside from three destroyers and six naval colliers. In the period from to the Bethlehem-Fairfield yard built 116 ships, including sixty- eight tankers, twenty-six general cargo ships, ten refrigerated cargo ships, six ore carriers, and six passenger/cargo ships. The yard employed over people during the height of production in World War II.9

Description

The Taluga was in overall length with a 75' beam and draft of The American Bureau of Shipping rated the vessel at gross tons and deadweight tons. The ship displaced tons. The twin-screw propulsion plant created shaft horsepower for a top speed of knots, with an average cruising distance of around miles. The ship maintained a raked bow, cruiser stern, and the three islands. 10 The machinery space contained four steam turbines built by Bethlehem, as well as two Westinghouse generators on an intermediate deck that generated 400-kilowatts to produce a volt alternating current. Foster and Wheeler supplied the four boilers, which provided steam for the main turbines, auxiliaries, and pumps. The working steam pressure was 450 pounds per square inch at 750 degrees Fahrenheit.

Todd oil burners and Hagen controls provided combustion. Two Falk double helical reduction gears stepped the shaft power down. The aft steering compartment housed the quadrant steering gear manufactured by Hyde.11 The T3-S2-A1 design incorporated nine corrugated tanks. Tanks 2 through 9 were centered in the ship with side tanks on the port and starboard sides and cofferdams fore and aft. Tank 1 only had side tanks. The total cargo capacity was barrels of oil and gallons of gasoline. The upper deck held twenty-six cylindrical hatches with stairwells for access inside the tanks. Three pump rooms located aft, amidships, and forward were used to move the cargo. The main pump room was located aft and contained four pumps.

There were three main Ingersoll-Rand centrifugal pumps, rated at gallons-per-minute The electric motors to actuate the pumps were in separate compartments to prevent accidental ignition of the cargo fuel. The other pump was a Worthington vertical steam reciprocating pump used for stripping. The amidships pump room contained three pumps, including two centrifugal steam cargo pumps, rated at and manufactured by Pacific. The remaining pump was vertical steam- reciprocating and manufactured by Worthington Pump. It was rated at gpm and primarily used for stripping. The forward pump room contained one vertical steam-reciprocating pump manufactured by Worthington and rated at This pump was used solely for the 9 Sawyer and Mitchell, Victory Ships and Tankers, p.

28; Fairfield Shipyard, at accessed 13 March 10 U.S. Navy, Ships Data U.S. Navy Vessels: Auxiliary, District Craft, and Unclassified Vessels (Washington, DC: Government Printing Office, pp. 11 The description is based on the U.S. Navy, Ships Data, pp. and Booklet of General Plans (AO-62) in Record Group 19, National Archives and Records Administration College Park, Maryland. Taluga HAER No. CA-336 Page 6 transfer of cargo fuel. All the pump rooms were accessed through small pump houses on the upper deck that contained stairwells. The cargo deck held a variety of equipment. On the after deck were two kingposts located in the after well that handled the fuel and steam lines through 10-ton and 30' booms. There was also a boom located off the mainmast, like the kingposts.

In addition, two more kingposts were located just aft of the bridge that supported two booms for fueling and launching two 40' utility craft. Winches serviced the booms during refueling operations and launches. There were six fueling stations located on this deck, three per side. To help prevent accidents on the ship and to carry miscellaneous equipment, a wooden spar deck was built above the piping equipment. The foredeck included one 10-ton boom located off the foremast for handling fueling lines. Two winches serviced the boom. There were two fueling stations located on the port and starboard sides, just aft of the forecastle deck. An elevated catwalk connected the bridge deck to the forecastle deck so personnel could avoid the piping.

The storerooms and ballast compartments were beneath the foredeck, along with spaces for repair and parts, paint, electrical equipment, and clothing. The forepeak stored fresh water for the crew. Aft of the forepeak were two dual-purpose tanks that could store either ballast or fuel oil. The T3-S2-A1 was equipped with armament. One 5"/38-caliber dual-purpose gun was located on the stern, while four twin-mounted guns were atop the boat deck just forward of the stack. Lastly, four 3"/50-caliber twin-mounted guns were on the bow. Two ammunition lockers supplied the guns. The forward ammunition storeroom was below the chain locker and under the waterline for protection. The rear ammunition locker was aft of the after peak and also under the waterline.

The locker supplied the 5" gun on the poop deck. Elevators transported the ammunition while integrated flash protection prevented an internal explosion during an attack. Accommodations for the forty-four-person crew consisted of two berthing areas and a galley. The middle island contained accommodations for the officers while the aft island held the majority of the berths for the enlisted crew. The crew s mess for enlisted and officers was in the aft island. Navigation and communication equipment were located in the middle island. Standard navigation equipment on the bridge consisted of a steering station, binnacle, gyro repeater, gyro pilot, engine telegraph, charts, and a fathometer. Radar and Loran became standard after World War II.

The upper bridge deck housed the radio room and the cryptographic equipment. The pilothouse contained a second steering station, binnacle, and gyro repeater. Lifesaving equipment onboard consisted of small boats on either side of the tanker. There was enough space for the entire crew on each side because a sinking ship tended to list, and the elevated side prevented the crew from deploying the life-saving craft. The lifeboats (twenty- five-man-capacity) contained quick-release tackle on special skids. There were two additional life rafts suspended from inclined troughs. Emergency kick-out panels on divisional bulkheads Taluga HAER No. CA-336 Page 7 in the living quarters and chain ladders in the ventilation ducts provided egress from ship compartments.

Underway Replenishment

By the U.S. Navy began using underway support missions since warships were at sea for longer periods of time and using more ammunition. The U.S. Navy formed the Logistic Support Group, with ammunition and store ships utilizing underway replenishment techniques. Navy oilers, like the Taluga, supplied vessels-at-sea using underway replenishment, which involved two or more vessels reaching similar speed and course. With the ships on a parallel course and at a close distance, the oiler s crew would pass a line to the receiving ship. These high-strength lines allowed cargo and fuel lines to be pulled across to the receiving ship. The oiler s boom held the fuel hose through a saddle, and the receiving vessel attached the hose to the bunker for refueling.

Underway replenishment became standard procedure for replenishing the battle fleet in World War II.12

Operational History

The Taluga, named after a river in Florida, was launched on 10 July with Harvey Klemmer as sponsor. The ship arrived in Norfolk on 25 August under Commander Hans M. Mikkelsen and was commissioned that day. Mikkelsen sailed for the Pacific via the Panama Canal with a stop in Aruba. In December, the Taluga reached Ulithi, which became the center of its operations until the end of the war.13 The Taluga s mission consisted of taking oil and aviation gas to the ships in the Carrier Task Force. The ship provisioned the task force for eleven months while strikes and landings were conducted against the Japanese on Luzon, Okinawa, Formosa, and the last attack on Japan s home islands. In April and July the ship maintained station in and around Kerama Retto, the southwestern part of Okinawa.

In this area on 16 April, the Japanese launched a kamikaze attack on the formation. Ten Japanese aircraft struck, and one plane peppered the Taluga s decks before aiming for the bridge. The aircraft bounced off the side of the bridge and exploded on the deck into an adjacent compartment beside a tank carrying aviation gas. Twelve men suffered injuries, none fatal, and the ship resumed operations shortly thereafter. After the Japanese surrender in August the Taluga became a station oiler in Japan. The ship s primary base was on Yokosuka, but it did make runs to Tsingtao and Jinsen to support the occupation of China and Korea. At the end of January, the ship was put to sea and returned to the United States for an overhaul in San Pedro, California.

From July to June the Taluga transported oil and gasoline to various bases around the globe. In after the establishment of the Military Sea Transportation Service, the Taluga 12 George, History of Warships, p. A.S. Bussey, Skillful Technique Developed in Replenishment at Sea, Bureau of Ships Journal 7 (July pp. 13 The operational history is compiled from the U.S. Navy, Dictionary of American Naval Fighting Ships, Vol. VII (Washington, DC: Naval Historical Center, pp. Taluga HAER No. CA-336 Page 8 was assigned to the unit. The ship carried oil to the East Coast for several months before sailing to its homeport of Long Beach, California.

With the onset of the Korean War, the Taluga headed for the combat zone in summer The ship operated out of Sasebo, Japan, supplying vessels around the blockade and siege of Wonsan and Songjin. After the Korean settlement, the Taluga supplied the Seventh Fleet until the outbreak of hostilities in Vietnam. In the Taluga began resupplying ships directly participating in operations against the North Vietnamese. Most of the ship s deployments were in or around the combat sectors. During the six deployments, the ship spent a majority of time with the Seventh Fleet, providing replenishment for the larger ships within the carrier task force and the smaller ships associated with Operation Market Time an operation directed against North Vietnamese infiltration and logistics.

Shortly after, the ship returned to the United States for decommissioning. In May the Taluga joined the Military Sealift Command and was renamed the USNS Taluga (T-AO-62). The U.S. Navy began testing the viability of civilian-crewed oilers within the fleet. The Taluga participated in the pilot program, Operation Charter Log II, and the navy hailed it a total success. The small crew, made up of 105 civil service mariners, proved that a civilian crew could perform the same tasks more efficiently and with less capital. The select and highly-trained crew was known as the Taluga Tigers. Ship operating costs were reduced from million/year to million/year. Additionally, the success of Operation Charger led the navy to transfer additional oilers to MSC for operations in support of the fleet.

In the Taluga underwent an overhaul that enhanced fueling equipment. New kingposts with hose outriggers were added, along with ram tensioners. Electric-hydraulic winches supplanted old steam winches. The fueling points on the starboard side were fitted with 7 hoses and port side stations received dual probe fueling systems. After the overhaul, the ship began servicing the Third Fleet in the eastern Pacific until October Shortly after that date, the ship was decommissioned. CONCLUSION During its service from to the Taluga received four battle stars during World War II, four battle stars during the Korean War, and twelve during the Vietnam War.

The Taluga remains noteworthy as an example of a T3-S2-A1 fleet oiler as well as for its transitional role as a civilian oiler that helped promote more civilian-run ships within Military Sealift Command. Taluga HAER No. CA-336 Page 9 APPENDIX A: HISTORIC PHOTOGRAPHS Figure 1: Aerial photograph of the USS Taluga (AO-62), 6 October Negative Box Record Group 80, National Archives and Records Administration-College Park, Maryland. Taluga HAER No. CA-336 Page 10 Figure 2: Aerial photograph of the USS Taluga (AO-62) off Norfolk, VA, 2 September Negative (AO-62), Box Record Group 80, National Archives and Records Administration-College Park, Maryland. Taluga HAER No.

CA-336 Page 11 Figure 3: Aerial photograph of the USS Taluga (AO-62) refueling the aircraft carrier USS Hancock (CVA-19) and the destroyer USS Ingersoll 15 May Negative Box 14, 428-GX-AO 62, Record Group 80, National Archives and Records Administration-College Park, Maryland. Taluga HAER No. CA-336 Page 12 Figure 4: The USS Taluga (AO-62) refuels the USS Galveston 8 December Negative Box 14, 428-GX-AO 62, Record Group 80, National Archives and Records Administration-College Park, Maryland. Taluga HAER No. CA-336 Page 13 Figure 5: The USS Taluga (T-AO-62) refuels the aircraft carrier USS Kitty Hawk July Negative Box 14, 428-GX-AO 62, Record Group 80, National Archives and Records Administration-College Park, Maryland. Taluga HAER No.

CA-336 Page 14 APPENDIX B: LIST OF T3-S2-A1 OILERS CONSTRUCTED AND THEIR DISPOSITIONS Yard Hull # MC # Original Name Delivered Disposition Bethlehem 8 Platte 1-Dec-39 To USN as Platte (AO-24), converted to CVE 27 scrapped Bethlehem 9 Esso Annapolis 26-Jan-40 To USN as Chemung (AO- scrapped Bethlehem 10 Esso Albany 15-Sep-40 To USN as Sabine (AO- Bethlehem 717 Ashtabula 7-Aug-43 To USN as AO-51, sunk as target Bethlehem 718 Cacapon 21-Sep-43 To USN as AO-52, disposition unknown Bethlehem 719 Caliente 22-Oct-43 To USN as AO-53, Bethlehem 720 Chikaskia 10-Nov-43 To USN as AO-54, Bethlehem 721 Elokomin 30-Nov-43 To USN as AO-55, scrapped Bethlehem 722 Aucilla 22-Dec-43 To USN as AO-56, Bethlehem 723 Marias 12-Feb-44 To USN as AO-57, scrapped Bethlehem 724 Manatee 6-Apr-44 To USN as AO-58, disposition unknown Bethlehem 725 Mississinewa 18-May-44 To USN as AO-59, torpedoed and lost at Ulithi Island Bethlehem 726 Nantahala 19-Jun-44 To USN as AO-60, Bethlehem 727 Severn 19-Jul-44 To USN as AO-61, Bethlehem 728 Taluga 25-Aug-44 To USN as AO-62, Bethlehem 729 Chipola 30-Nov-44 To USN as AO-63, Bethlehem 730 Tolovana 24-Feb-45 To USN as AO-64, Taluga HAER No.

CA-336 Page 15 Federal 151 5 Markay Jun-39 To USN as Suwanee (AO-33), converted to CVE 27 scrapped Federal 152 6 Neosho Aug-39 To USN as Neosho (AO-23), bombed and scuttled off New Guinea Federal 153 7 Esso Trenton Dec-39 To USN as Sangamon (AO-28), converted to CVE 26 scrapped Newport 370 11 Esso Richmond To USN as Kaskasia (AO-27), scrapped Newport 371 12 Esso Raleigh To USN as Guadelupe (AO- scrapped Newport 372 13 Esso Columbia To USN as Salamonie (AO- scrapped Sun D&D 172 2 Cimarron To USN as Cimarron (AO-22), scrapped Sun D&D 173 3 Seakay To USN as Santee (AO-29), converted to CVE 29 scrapped Sun D&D 174 4 Esso New Orleans To USN as Chenango (AO- converted to CVE 28 scrapped Bethlehem Allagash 21-Aug-45 To USN as AO-97, Bethlehem Caloosahatchee 10-Oct-45 To USN as AO-98, jumboized scrapped Bethlehem Canisteo 3-Dec-45 To USN as AO-99, jumboized scrapped Bethlehem Chukawan 22-Jan-46 To USN as AO-100, scrapped Taluga HAER No.

CA-336 Page 16

Bibliography

Books Cudahy, Brian J. Box Boats: How Container Ships Changed the World. New York, NY: Fordham University Press, De La Pedraja, Ren . A Historical Dictionary of the U.S. Merchant Marine and Shipping Industry since the Introduction of Steam. Westport, CT: Greenwood Press, George, James L. History of Warships: From Ancient Times to the Twenty-First Century. Annapolis, MD: Naval Institute Press, Lane, Frederic C. Ships for Victory: A History of Shipbuilding under the U.S. Maritime Commission in World War II. Baltimore, MD: The Johns Hopkins Press, Sawyer, L.A. and Mitchell. From America to the United States: The History of the Merchant Ship Types Built in the United States of America under the Long-Range Programme of the Maritime Commission.

Kendal, UK: World Shipping Society, Victory Ships and Tankers: The History of the Victory Type Cargo Ships and of the Tankers Built in the United States of America during World War II. Cambridge, MD: Cornell Maritime Press, Inc., U.S. Navy. Dictionary of American Naval Fighting Ships. Vol. VII. Washington, DC: Naval Historical Center, Ships Data, U.S. Naval Vessels: Vol. III Auxiliary, District Craft and Unclassified Vessels. Washington, DC: Government Printing Office, Articles Bussey, A.S. Skillful Techniques Developed in Replenishment at Sea. Bureau of Ships Journal 7 (July pp. Wildenberg, Thomas. The Origins and Development of the T2 Tanker. American Neptune (Summer pp. Public Documents Booklet of General Plans (AO-62).

Record Group 19, National Archives and Records Administration-College Park, Maryland.

In context

Benicia, California The place record: every map, photograph and survey of this town.
Solano County, California 258 topographic sheets across the county.
Library of Congress record The original filed report as the survey filed it.

Also surveyed in Benicia

24 of 57 records shown

The federal surveyors worked through Benicia building by building. These are the other structures they measured and filed a report on, longest report first.

SheetStructure SurveyReport
American RacerHAER CA-34614,934 words
USNS CometHAER CA-3489,619 words
Benicia State CapitolHABS CAL,48-BENI,2-5,680 words
US Coast Guard Icebreaker GlacierHAER CA-3415,404 words
Esso GettysburgHAER CA-3545,367 words
WichitaHAER CA-3565,295 words
St. Paul's Episcopal ChurchHABS CAL,48-BENI,15A-4,754 words
General Edwin D. PatrickHAER CA-3444,661 words
Alaska StandardHAER CA-3474,624 words
Benicia ArsenalHABS CAL,48,BEN1,4-S-4,440 words
SperryHAER CA-3424,323 words
General John PopeHAER CA-3433,965 words
Mission Santa YnezHAER CA-3373,807 words
SS PetersburgHAER CA-23323,637 words
BolsterHAER CA-3553,326 words
Benicia ArsenalHABS CAL,48-BENI,4T-2,980 words
Crooks HouseHABS CAL,48-BENI,7-2,938 words
Riddell Fish HouseHABS CAL,48-BENI,8-2,747 words
Winthrop VictoryHAER CA-3452,735 words
MispillionHAER CA-3382,700 words
Benicia ArsenalHABS CAL,48-BENI,4P-2,542 words
Fischer-Hanlon HouseHALS CA-272,442 words
Carr HouseHABS CAL,48-BENI,6-2,067 words
Benicia ArsenalHABS CAL,48-BENI,4J-1,951 words

Provenance

  • Written history. Quoted verbatim from HAER CA-336. United States federal work, no copyright under 17 U.S.C. 105.
  • Text capture. Machine-read from the scanned typescript filed with the survey, so spelling and spacing follow the original page.
  • How this page is made. Documentary passages are quoted from the linked federal record; page labels and counts are clearly marked as site presentation or calculations.