The Engineering Building is a contributing structure in the United Engineering Company Shipyard historic district that has been determined eligible for the National Register of Historic Places. The United Engineering Company Shipyard, established in to build and repair ships for the U.S. Navy, is the last surviving of several large World War II shipyards in Alameda. United Engineering built 21 tugboats and repaired hundreds of ships during the war. The facility was one of the largest employers in Alameda and played an important economic and social role in the city.
Built in part to provide facilities for 300 women, the Engineering Building represents both the effects of the war on the traditional labor supply in the Bay Area and also the contribution of women to the work of the United Engineering Company during World War II. In addition, the building represents the role of two essential functions in the shipyard complex: engineering design and sheet metal work. Description: The Engineering Building is a two-story rectangular-shaped building. It measures 200 feet across the east and west facades and 60 feet across the north and south facades. The structure has a total area of square feet. Like many of the buildings constructed at the yards from the Engineering Building is utilitarian in appearance and has little ornamentation.
The building rests on rows of wooden piers. The western piers are sunk in dry land and the eastern piers are sunk in the Wet Basin. As a result, the building sits partially on land and partially above water. The building is composed of a wooden post and beam structural system covered with wood channel rustic siding on the exterior. The roof is basically flat with a slight pitch ostensibly for drainage. Six vents and what appears to be a whistle are located on the roof. UNITED ENGINEERING COMPANY SHIPYARD, ENGINEERING BUILDING (Sheet Metal Shop, Building No. Building No. Building No. 18) HAER No. CA-295-J (Page 2) Most windows are double-hung, six-over-six divided lights with wooden sashes. Others are three-by-three divided light awning windows.
Several doorways have the original three-by-two divided light, half-glassed doors. However, many others have been replaced with wooden hollow core doors or covered with pressed board. There is a pair of large, wooden, garage doors on the east elevation. Historically there were staircases to the second floor on the west and south elevations. The south staircase has been removed. The building was fully plumbed and had steam heat. The first floor is divided into two sections. The smaller portion is located at the south end and is closed off from the rest of the building. It is only accessible from exterior doors on the south and west facades. The remaining portion of the first floor is a very large space that is open except for two small rooms in the southwest corner.
The walls and ceiling are unfinished with exposed structural members. The floors retain their original treatment, which is wood planking covered by 2 inches of asphalt. Two rows of wooden beams support the second floor. On both floors some of the original fluorescent light fixtures, which were hung on the diagonal, are still extant. The second floor is also composed principally of a large open space with small rooms on several sides. The north end has a long office, which contains what appears to be a blueprint machine circa The east side has a women's restroom, vault, and men's restroom. The vault is constructed of reinforced concrete and rests on reinforced concrete piers located on the first floor. The west side of the building has three small rooms surrounding the entrance.
The south end of the floor has five small rooms and a hallway (these room appear to be later additions). The floor is wood planking covered with linoleum in some areas. The building has been little altered and retains a high percentage of original fabric. However, the building is seriously deteriorated. Historical Context: In a memo from United Engineering to the Navy's Bureau of Ships dated 20 December was requested for this building for three purposes: Women's quarters, a sheet metal shop, and an engineering department. These purposes were justified as follows: 1. Women's Quarters. The man power labor supply has become limited in this district and this Company, like other ship-building companies in the vicinity, has found it necessary to employ women in the production department.
There are now no r sanitary or rest room facilities in the yard for UNITED ENGINEERING COMPANY SHIPYARD, ENGINEERING BUILDING (Sheet Metal Shop, Building No. Building No. Building No. 18) HAER No. CA-295-J (Page 3) women workers. It will be necessary to build such facilities sufficient to accommodate at least 300 women. 2. Sheet Metal Shop. The present Sheet Metal Shop... has been found entirely inadequate to accommodate both the ship repairing and the ship building work of the Sheet Metal Department, as it has developed that a very large quantity of sheet metal work is required in the repair and conversion of Navy vessels. It is necessary that sq. ft. be set aside for this purpose. 3. Engineering Department.
This department is now located in the second floor of a section of the main shop building. It is obvious that this space will be inadequate for the following reason - The United Engineering Company is the designing agent for Fleet Tugs and, because of major alterations in design, has found it necessary to r~, expand this engineering department extensively. It has also been found that the burden of engineering work in connection with repairs requires expansion of this department. Because of lack of space, outside engineering agencies have been employed to assist in expediting engineering work in connection with conversion and repairs. This arrangement is not satisfactory nor dependable.
The women's quarters and sheet metal shop were to occupy the ground floor and the engineering department was to occupy the second floor. The Engineering Building was built in during a construction campaign by United Engineering. The company quickly built numerous buildings to accommodate shipbuilding and repair necessitated by U.S. involvement in World War II. Plans for the Engineering Building were drawn on 1 March by Alben Froberg, a local architect practicing in Oakland, California. The U.S. Navy Bureau of Yards and Docks approved the building for construction just two days later. On the original plans, the building was designated Building The first floor was a sheet metal shop and the second floor was the ^~ engineering department.
Plans showed the northern two thirds of the ( first floor as a large open space called "shop" with rows of UNITED ENGINEERING COMPANY SHIPYARD, ENGINEERING BUILDING (Sheet Metal Shop, Building No. Building No. Building No. 18) HAER No. CA-295-J (Page 4) workbenches placed throughout. Along the edges were spaces for machines such as "shear," "rotary shear," "press," "seamer," "elbow machine," and "welding." At the south end there was a "tool room," "office," a small "boiler room," and a large "locker room" with a "rest room" and "women's lav."1 The second floor was also a large open room: it was used for drafting. At the north end there was a blueprint room.
In the middle of the building along the east wall, the plans called for three rooms - a "women's toilet", "vault," and a "men's toilet." Across the building on the west wall there was a small office and a reception room.2 In the Engineering Building was listed by Alameda County as building no. 41. By the end of the period of ownership by the Todd Shipyards Corporation, it was called building a designation that continues to be used today.